ECO Spot LED B90E User manual

ECO Spot LED B90E/B150E/B300E User Manual
Copyright © 2015 Globus New Media LLC Page 1
Thank you for choosing an ECO Spot™ Gobo projector.
Please read this manual before installing or operating this fixture,
follow the safety precautions listed below and observe all warnings.
WARNING! - To prevent damage to the LED, always
connect the driver to the projector FIRST before
powering up the driver.
Package Contents
Projector with Projection Lens
External LED Driver
Test Gobo mounted
Thread ring with silicone seal for the projection lens
Safety Information
Electrical Safety
•Disconnect the fixture from AC power before handling it.
•Follow all local building and electrical codes and apply both, overload and
ground-fault protection.
•Do not use the fixture if the power cable or power plug is in any way damaged,
defective or wet, or if they show signs of overheating.
•The fixtures have power plugs for testing and for indoor use but exterior
installations usually require hard-wired connections. Follow all related codes.
ECO Spot
™ LED B90E/B150E/B300E
Exterior User Manual
•Place your fixture at a suitable place with good air flow.
•Keep flammable materials away from the fixture.
•Minimum distance to flammable material = 1 ft (0.3m).
•Provide a minimum clearance of 4 in (10cm) around air vents.
•Do not look directly into the lamp; it can result in eye damage.
•Always unplug the unit from the power mains before any service is done.
•Light fixtures should be installed and maintained only by qualified personnel with
experience in lighting equipment and general electrical experience.

ECO Spot LED B90E/B150E/B300E User Manual
Page 2 Copyright © 2015 Globus New Media
LLC Page 2
Outdoor Use
The projector and external driver are designed for outdoor use. The rear, perforated
cooling part of the projector including the fan is rated for water exposure. To extend the
projector life, an external hood can be placed above the projector but this measure is not
mandatory.
Handling Instructions
Warranty
One Year from Date of Purchase. Keep your receipt for reference and contact your dealer
in case of warranty issues.
Projection Lenses
The projector accommodates interchangeable projection lenses to allow optimizing the
projection size and resulting brightness at varying distances. The more narrow the lens,
the smaller and brighter the image will be at a given distance.
Focusing
Gobo Rotator
If the fixture is equipped with a gobo rotator, it can be turned on/off with the silver push-
button on the front plate underneath the lens. There are no controls for rotating speed or
direction. Even when not used, the gobo rotator comes handy for straightening the gobo
image after a gobo was installed.
•Before the initial start-up, please unpack and carefully check for damage caused
during transportation.
•When suspending the fixture above ground level, verify that the structure
can hold
at least 10 times the weight of all installed devices.
•Verify that all external covers and rigging hardware are securely fastened and use
an approved means of secondary attachment such as a safety cable.
•Power up the projector.
•If the fixture is equipped with a gobo rotator, turn it on and then off again once
the gobo projects in the desired position.
•Loosen the outer ring around the lens that acts as a water seal.
•Focus the projection by twisting the lens in and out until
the image is well focused.
When used for the first time, the lens will often need to be twisted outwards many
rotations to reach the focusing point. When in doubt, keep going.
•Re-tighten the outer ring with the seal to ensure the lens won’t leak water.

ECO Spot LED B90E/B150E/B300E User Manual
Copyright © 2015 Globus New Media LLC Page 3
Multi-functional Yoke
Gobo Placement
The Projector uses M-Size gobos, (see Specifications for Gobo Dimensions).
The yoke can slide over the fixture body to accommodate a wide range of pointing
directions. It can serve as stand or can be mounted to a wall, ceiling or truss.
•Pointing position UP: With the long-hole pointing towards the back of the
projector, the main pointing position is UP.
•Pointing position DOWN: Remove the yoke screws and flip the projector so the
long-hole points to the front plate.
•If the projector is on, turn it off.
•Even though this is a LED projector, the gobo gets hot, please wait a few minutes
for the gobo to cool down if the projector was on.
•Unscrew the thumbscrews to remove the front cover with the projection lens.
Keep the rubber seals and re-use them with the thumb screws to prevent leakage.
•Push the two pins of the gobo retaining ring together and pull out the retaining
ring. Carefully remove the old gobo and replace it with the new gobo.
•If you have a glass gobo, place the more reflective side towards the light bulb.
•Replace the retaining ring and make sure it evenly pushes the gobo all the way
back.
•Replace the front cover and rubber seals and tighten the thumb screws well.
•Adjust the focus by twisting the projection lens in or out.
•Re-tighten the lens retaining ring towards the front plate so the silicone ring
makes a water tight seal.

ECO Spot LED B90E/B150E/B300E User Manual
Page 4 Copyright © 2015 Globus New Media
LLC Page 4
Power Supply
90-265V, 50/60Hz
B90E: 110W, B150E: 180W, B300E: 360W
Ambient Operating Temperature
-13 to 104°F (-25 to 40°C)
Dimensions / Weight
Fixture Body: 7.5in x 5.5in x 14.5in
(190mm x 140mm x 370mm)
Total Length: 18in (460mm) with 25deg.
lens, 20in (510mm) with 15 deg. lens
Yoke Base: 6.4in x 7.8in (163 x 198mm)
Yoke Height: 7.5in ( 190mm) (from base
to center)
Total Height: 10in ( 254mm) (from base
to top)
Weight: B90E:12lbs (5.4kg), 150E:13lbs
(6kg), B300E: 17lbs (7.7kg)
Gobo Dimensions
Metal or Glass Gobos and Dichroic filters
Standard Gobo Size: M-Size
Outer Diameter (OD): 66mm
Image Diameter (ID): 48mm
Max Thickness:4mm
LED Lamp
Rated Bulb life:40,000h
Color Temperature:6,000k, +/-500k
Rated luminous flux:
B90E: 7,500lm, B150E: 12,000lm,
B300E: 20.000
Effective luminous flux:
B90E: 6,200lm, B150E: 8,900lm,
B300E: 11,500lm
CRI: 75
Lens Options
The projector can be equipped with
standard ECO Spot projection lenses.
A larger focal length (f) makes a smaller
projection angle and therefore a smaller
but brighter image. Currently these
lenses are available:
IP-Ratings
LED Driver: IP65, Fixture: IP55
•Medium-Narrow f=115mm 25º
•Medium f=140mm 20º
•Semi-Narrow f=140mm 15º