ECO Spot C20PCE User manual

ECO Spot LED C20PCEUser Manual
Copyright ©2020 Globus NewMedia LLC Page 1
Package Contents
Projector with driver and power cord, lens
Test Welcome Gobo
Gobo Holder
Allen key for yoke adjustment
Safety Information
Electrical Safety
Warranty
One Year from Date of Purchase. Keep your receipt for reference and
contact your dealer in case of warranty issues.
ECO Spot™ LED C20PCE User Manual
Thank you for choosing an ECO Spot™ Gobo projector. This manual
covers the ECO Spot C20PCE.
Please read this manual before installing or operating this fixture,
follow the safety precautions listed below and observe all warnings.
•Place your fixture at a suitable place with good air flow.
•Keep flammable materials away from the fixture.
•Minimum distance to flammable material = 1 ft (0.3m).
•Provide a minimum clearance of 4 in (10cm) around air vents.
•Use only genuine spare parts for part replacement.
•Do not look directly into the lamp; it can result in eye damage.
•Always unplug the unit from the power mains before any service is done.
•Light fixtures should be installed and maintained only by qualified personnel with
experience in lighting equipment and general electrical experience.
•Disconnect the fixture from AC power before handling the fixture.
•Always ground (earth) the fixture electrically.
•Use only a power source
that complies with local building and electrical codes and
has both, overload and ground-fault protection.
•Do not use the fixture if the power cable or power plug is in any way damaged,
defective or wet, or if they show signs of overheating.

ECO Spot LED C20PCEUser Manual
Page 2 Copyright © 2020 Globus NewMedia LLC
Handling Instructions
Projection Lenses
The projector accommodates interchangeable projection lenses to allow optimizing the
projection size and resulting brightness at varying distances. The narrower the lens, the
smaller and brighter the image will be at a given distance.
Focusing
Gobo Rotator
This Model does not have Gobo rotation.
Dimming
This Model doesn't support dimming or brightness adjustment.
Yoke
•Before the initial start-up, please unpack and carefully check for damage caused
during transportation.
•Place your fixture at a suitable place with good air flow.
•Make sure there are no flammable materials close to the lamp.
•When suspending the fixture above ground level, verify that the structure
can hold
at least 10 times the weight of all installed devices.
•Verify that all external covers and rigging hardware are securely fastened and use
an approved means of secondary attachment such as a safety cable.
•Power up theprojector by pressing the power switch in the back.
•Focus the projection by twisting the lens in and out until the image is well focused.
When used for the first time, the lens will often need to be twisted outwards many
rotations toreach the focusing point.
•Re-adjust the focus if necessary.
•The projector is mainly designed for wall and ceiling mounting but in many cases,
it can also be placed on a table or shelf.
•The yoke allows projector movement inone direction:
Up/down.

ECO Spot LED C20PCEUser Manual
Copyright ©2020 Globus NewMedia LLC Page 3
Gobo Placement (see Specifications for Gobo Dimensions)
The projector uses E-Size gobos. See the Specifications for exact dimensions.
•Unscrew the thumbscrew and screw into gobo holder to remove.
•Push the two pins ofthe gobo retaining ring together and pull out the retaining
ring. Carefully remove the old gobo and replace itwith the new gobo.
•If you have a glass gobo, place the more reflective side towards the light bulb.
•Replace the retaining ring and make sure it evenly pushes the gobo all the way
back.
•Place the gobo holder in the slot and unscrew the thumb screw to lock it. Screw
the thumb screw into thread in front of gobo holder so it is not lost. Adjust the
focus by screwing the projection lens in or out until you reach a focal point, then
fine tuning focus can be down with single turns to achieve full focus.

ECO Spot LED C20PCEUser Manual
Page 4 Copyright © 2020 Globus NewMedia LLC
Power Supply
100-240/277V, 50-60Hz, 25W
Dimensions / Weight
Base: 2.75" x 3"
Total Length: 8 - 10" - depends on lens
Total Height: 5.5" (incl. yoke)
Weight: 2.4lbs
The projection lens adds 0.5 to 2in (12 to
50mm) to the length.
Gobo Dimensions
Metal or Glass Gobos and Dichroic filters
with up to3.3mm thickness. Film Gobo
Life - 2 - 5 days.
Standard gobo size (E-Size):
Outer Diameter (OD): 37.5mm
Image Diameter (ID): 27mm (max 32mm)
The recommended gobo image diameter
for best focusing is up to 25mm. An
image diameter of upto32mmis
possible with some yellowing and
focusing weakness in the outer
projection area.
LED Lamp
Lens Options
The projector can be equipped with
standard ECO Spot projection lenses.
A larger focal length (f) makes a smaller
projection angle and therefore a smaller
but brighter image. Currently these
lenses are available:
Ambient Operating Temperature
-22 to 122°F (-30 to 50°C)
•Power: 20W
•Rated luminous flux: 1,800lm
•Effective luminous flux: 1,000lm
•Rated Bulb life 30,000h
•Color Temperature 7,000k,
+/-500k
•Wide f=56mm, 25º
•Semi-Narrow f=100mm, 15º