ECOTRIKES ET4 User manual

Owner’s Manual
ET4 ET6
Email: [e-mail]
www.EcoTrikes.com
EcoTrikes

Table of Contents
Technical Information-----------------------------------1
Warning Statement--------------------------------------2
Read Before Riding-------------------------------------3
List of Parts-----------------------------------------------4
Front Bar---------------------------------------------------6
Tool Kits In The Tool Bag------------------------------7
Assembling The Multi-Point---------------------------8
Charging The Batteries-------------------------------12
Charging The Batteries Outside Scooter---------13
Riding The Multi-Point--------------------------------15
Folding The Multi-Point-------------------------------19
Maintenance---------------------------------------------21
Wiring Diagram-----------------------------------------22
Trouble Shooting Guide------------------------------24

Warranty-------------------------------------------------26
Instructions for optional attachments-------------31

1
T
Te ec ch hn ni ic ca al l I In nf fo or rm ma at ti io on n
EcoTrikes
Model No.
EcoTrikes ET4 and ET6
Product size
45 L x 27 W x 44 H inch
(115 x 68 W x 113 cm)
Type of motor
Permanent-magnet
brushless DC wheel motor
Motor power
500 w Wheel motor, 48 V
Battery type
sealed lead acid battery
Battery capacity
48 Volt, 12Ah
Charger
110V-240V, UL approved
Charging time
4-6 hours
Max. speed
Up to 16 MPH ( 26 km/h)
Single charge
Up to 31 MILES (50 km)
Max capacity
310 LBS (158 kg)
Net weight
101 LBS (46 kg)

2
W
Wa ar rn ni in ng g S St ta at te em me en nt t
EcoTrikes
Do not ride this scooter until you read thoroughly understand
the owner’s manual. It contains information critical to your safety. If you
have any questions about the operation of the scooter, you should consult
your authorized dealer
It is extremely important that you follow the safety guidelines
contained in this manual in order to ensure maximum safety.
Failure to comply with the standards outlined in the manual
could result in fire and/or serious injury.
EcoTrikes LLC is not liable for any damage or injuries
caused by unsafe or faulty repairs. Any repairs made to this product by
unauthorized service technicians are the sole responsibility of the owner.
Our products are designed to be ecologically conscious;
please dispose of used battery in compliance is with the local laws.
IMPORTANT!
Before you operate your ET4, please read
carefully:
YOUR EXISTING INSURANCE POLICY MAY
NOT COVER FOR ELECTRIC VECHILCES;
YOU SHOULD CONTACT YOUR INSURANCE
AGENT TO DETERMINE IF YOUR COVERAGE
IS PROVIDED.

3
R
Re ea ad d B Be ef fo or re e R Ri id di in ng g
EcoTrikes
WARNING
THE EcoTrikes Scooters are NOT A TOY AND SHOULD
NOT BE OPERATED BY ANYONE UNDER 12 YEARS
OLD.
Safety Instructions:
(Please take note of the following before each ride)
The maximum weight capacity is 310 lbs.
Only one person at a time should ride.
Always wear protective gear including knee and elbow pads and
an approved safety helmet when riding the EcoTrikes scooters
Before riding, be sure to check that all pivot points, locking
buttons, quick releases, and latches are secured properly.
The power switch lock must be in the “off” position when the
EcoTrikes Scooter is being charged.
Do not use the EcoTrikes Scooter when it is raining.
Do not place the battery near heat or fire.
Do not expose the charger to water or any moisture.
Check if batteries are properly charged and installed.
Charge Batteries after each use.
Always ride on dry paved surfaces. Gravel, wet, extreme
incline, and uneven surfaces are a hazard.
C
Ch he ec ck k i if f a al ll l t ti ir re es s a ar re e p pr ro op pe er rl ly y i in nf fl la at te ed d. .

4
L
Li is st t o of f P Pa ar rt ts s
EcoTrikes

5
L
Li is st t o of f P Pa ar rt ts s
EcoTrikes
1 Throttle
2 Multi-function Instrument
3 Brake lever
4 Alloy handlebar tub
5 Quick release
6 Connecting tube
7 Seat
8 Charger port
9 Footboard
10 Rear wheel
11 Battery
12 Power connecting plugs
13 Allen set screw
14 Front fender compartment
15 Front fork
16 Motor
17 Front wheel
18 Basket

6
F
Fr ro on nt t B Ba ar r
EcoTrikes
1 Brake lever
2 Lock mechanism switch
3 Horn switch
4 Multi-function Instrument
5 Key switch
6 USB port
7 Throttle

7
T
To oo ol l K Ki it ts s I In n T Th he e T To oo ol l B Ba ag g
EcoTrikes
1 Screwdriver
2 Allen wrench （2.5mm）
3 Allen wrench （3mm）
4 Allen wrench （5mm）
5 Allen wrench （6mm）
6 Wrench (8 x 10mm)
7 Wrench (16 x 18mm)
8 Wrench (16 x 18mm)
9 Charger

8
A
As ss se em mb bl li in ng g T Th he e E Ec co oT Tr ri ik ke es s U Un ni it t
EcoTrikes
1. Unpack the EcoTrikes scooter carefully so
that you do not misplace any of the parts.
2. Place the EcoTrikes unit on a flat, level
surface. Block the front up 3.5''. This will
make the next step easier
3. Remove the bolts and nuts from the
connecting tube clamp (B). Place the
connecting tube into the top opening (A).
After aligning the holes, place the two bolts
through the connecting tube and neck
assembly. Twist the bolts, do not hammer
them through. Tighten these two bolts with the
nuts provided.

9
A
As ss se em mb bl li in ng g T Th he e E Ec co oT Tr ri ik ke es s U Un ni it t
EcoTrikes
4. The two Allen set screws on the front of the
connecting clamp are for removing any play
after the bolts have been tightened. First,
back off the nuts, second, set the screws,
third, tighten the nuts to prevent the screws
from backing off.
5. Extend the handle bar tube to full upright
position, and slide it into connecting with the
front fork.
*Note: The tube shaft is intentionally off center to
allow handlebars to fold to the side. Be sure to
Two Allen
set screws

10
A
As ss se em mb bl li in ng g T Th he e E Ec co oT Tr ri ik ke es s u un ni it t
EcoTrikes
align release button to pivot on brake handle side
6. Ensure that the handlebar is facing front, the
brake on the left side and the throttle on the
right, then tighten the handlebar tube collar
clamp using the enclosed 5mm wrench.
7. Plug in the two power connecting plugs into
the sockets. The design of each plug and
socket is different. Connect the ones which
best fit each other to finish the assembly.
8. Match the pins of the plugs to the holes of
the sockets. Note the alignment notches.

11
A
As ss se em mb bl li in ng g T Th he e E Ec co oT Tr ri ik ke es s u un ni it t
EcoTrikes
NOTE: Handle bar height adjustment. Handle
bar height can be easily adjusted by opening the
quick release on the handlebar tube to preferred
height, then firmly closing quick release.

12
C
Ch ha ar rg gi in ng g T Th he e B Ba at tt te er ri ie es s
EcoTrikes
●Before you ride the EcoTrikes unit for the first
time you must charge the batteries for 4-6 hours
or until charge light turns green using only the
supplied charger.
●To charge the batteries, plug the charger into
the charger socket located on the rear side of the
battery/controller compartment. Then plug the
charger into a wall outlet. Red light on charger
indicates charging, green light indicates charged.
Warning: Never charge scooter longer than
10 hours.

13
C
Ch ha ar rg gi in ng g T Th he e B Ba at tt te er ri ie es s O Ou ut ts si id de e S Sc co oo ot te er r
EcoTrikes
1. Turn off the key switch.
2
2. .
Lift the floor mat. Unscrew two bolts that
secure the battery cover and remove it.
3
3. .
Unplug the battery connection plug, unlock the
battery case, remove the battery, and charge
using the optional external charge wire and
provided charger.

14
C
Ch ha ar rg gi in ng g T Th he e B Ba at tt te er ri ie es s O Ou ut ts si id de e S Sc co oo ot te er r
EcoTrikes

15
R
Ri id di in ng g T Th he e E Ec co oT Tr ri ik ke es s u un ni it t
EcoTrikes
●Once you have completed the initial charge you
are ready to ride. Remember, this is not a toy.
The EcoTrikes unit can reach speeds up to 16
mph depending on the terrain and the weight of
the rider. You must wear a helmet and protective
pads. Be aware of all local laws and ordinances
that govern and/or restrict the use of powered
scooters. The laws and ordinances vary greatly
from municipality to municipality. It is your
responsibility to know and abide by your local
restrictions.
●To ride, insert the key into the key switch and
turn the key in clockwise direction till the first click.
The battery gauge will be illuminated indicating
that the battery is in operation. If you want to turn
on the front light, please turn the key to the
second click in clockwise direction.
●Hold onto the front bar with both hands. Your
left hand will control the brakes and your right

16
R
Ri id di in ng g T Th he e E Ec co oT Tr ri ik ke es s U Un ni it t
EcoTrikes
hand will control the throttle. As you turn the
throttle towards yourself, the speed will be
increased. Release the throttle and apply the
brake to stop the scooter. You will control the
speed of the scooter by using both the throttle
and the brake. When the brake handle is
squeezed it cuts power off the throttle.
NOTE 1: WARNING: Never try stunts. Always
maintain a safe speed.
NOTE 2: When scooter is parked, please remove
the key, this will avoid anyone from accidentally
turning the throttle causing the scooter to speed
forward. Failure to do this could lead to an
accident.
NOTE 3: If you need to stop in an emergency or
kill power quickly, you can turn the key off.
NOTE 4: Depending on skills of the driver, the
EcoTrikes unit comes equipped with an
adjustable speed switch located under the left
front side of the scooter under the 2 wire
connectors which allows you to limit speed to
8mph or switch to max speed of 16 mph.

17
R
Ri id di in ng g T Th he e E Ec co oT Tr ri ik ke es s U Un ni it t
EcoTrikes
NOTE 5: When you use reverse, the scooter
must be stopped, and then push the reverse
switch to “R”, the horn will send out a noise, then
GENTLY turn the throttle to back up. Warning,
do not twist throttle to full power when in
reverse. When finishing reverse, push the
reverse switch back to “F”.