EDAN MT-206 User manual

I
Table of Contents
目录
Installation Guide .......................................................................................1
安装指南 ....................................................................................................9

MT-206/MT-207 Trolley Installation Guide
- 1 -
WARNING
1 Assembling or disassembling of the Trolley should be performed by service
personnel authorized by the manufacturer.
2 The maximum load of the top splint is 8 kg. Do not put heavy objects on it
or lean on it.
3 The overall check of the Trolley, including the safety check, should be
performed only by qualified personnel once every 6 months, and each
time after fixing up.
4 The Trolley and accessories are to be disposed of according to local
regulations after their useful lives. Alternatively, they can be returned to the
dealer or the manufacturer for recycling or proper disposal.
5 Use a crosshead screw driver to secure all the screws tight when
assembling the Trolley.
CAUTION
When adjusting the stand post, be careful not to trap your fingers.
NOTE:
1 The following figures take M3 for example. The Trolley can also be used
for M3B, iM9 series, iM8 series, iM50, iM60, iM70, and iM80 monitor by
using a proper link board.
2 Make sure the casters can rotate normally before the setup.
3 Make sure the Trolley is firmly assembled and is in good condition before
applying the monitor to it.

MT-206/MT-207 Trolley Installation Guide
- 2 -
Chassis Handrail basket
Stand post
Top splint and link board
Caster

MT-206/MT-207 Trolley Installation Guide
- 3 -
Major Parts
Accessories
M3/M3B top splint assembly iM9/iM8 series top splint assembly
Handrail basket Lower basket (optional) Basket flange(optional) Stand post
M3/M3B link board assembly iM9/iM8 series link board assembly
A B C D.E.F G H I (M3) I (iM9) J

MT-206/MT-207 Trolley Installation Guide
- 4 -
Accessories:
Item Description Qty. (pcs) Spares (pcs)
A Ф12 Normal type spring washer 5 1
B Ф12 Normal type plain washer 5 1
C 3-inch Medical caster 5 /
D M10×50 bolt 1 /
E Ф10 Normal type spring washer 1 1
F Ф10 Normal type plain washer 1 1
G M6×25 spacing bolt 1 1
H Cross recessed pan head screw M5×14 4 2
I
M4×25 Cross recessed countersunk head
screw (only applicable to iM9 series, iM8
series, iM80 patient monitor)
4 2
M4×20 Cross recessed countersunk head
screw (only applicable to iM60, iM70
patient monitor)
4 2
M3×12 Cross recessed pan head screw
(only applicable to M3 series, iM50
monitor)
3 2
J 17# normal open spanner 1 /
NOTE：
1 Choose the appropriate I screws for different monitors.
2 The lower basket and flange should be used at the same time.
3 More screws are provided for standby in the package. Refer to the above
table for the actual numbers of screws required in installation.

MT-206/MT-207 Trolley Installation Guide
- 5 -
Procedure for Assembling Trolley:
1 Open the package and collate all the
parts with the packing list.
2 Take the chassis assembly out and
upturn it on the packing foam. Put an
A washer and then a B washer on the
bolt for each caster. Tighten the five C
casters to the chassis using the
provided spanner.
3 Tilt the chassis, and insert stand post
assembly into the groove of the
chassis. Make sure they are fixed well.
Install the D bolt, E washer and F
washer, then tighten them from the
center hole in the chassis.
4 For MT-207 trolley, a balancing
weight is installed on the chassis.
After installing the stand post as
shown in step3, install the D bolt, E
washer and F washer, then tighten
them from the countersink in the
chassis.
NOTE:
The caster has a pedal on it. You can
step on it to stop the Trolley, while push
it up to move the Trolley.
B
A

MT-206/MT-207 Trolley Installation Guide
- 6 -
5 The top splint and link board are
assembled together in package. Pull
downwards the pin on the top splint, hold
to slide them apart.
6 Loosen two screws on the top splint to take
off the rotary axis, then pull the rotary axis
through the flange hole of lifter rod.
Insert the L-shape angle adjustment handle
and a G screw into the two holes of flange,
but do not tighten them.
NOTE:
Put the L-shape angle adjustment
handle at the thinner side, while the G
screw on the other side.
7 Put the top splint on the flange of lifter
rod. Make sure it faces the hole of
rotary axis, then fix them well with
two screws taken off in step 6.
Tighten the L-shape angle adjustment
handle and the G screw.
A
ngle adjustment