Eddyfi Technologies INUKTUN SPECTRUM 90 User manual

2569 Kenworth Road, Suite C
Nanaimo, BC, V9T 3M4
CANADA
+1.250.729.8080
[e-mail]
www.eddyfitechnologies.com
INUKTUN SPECTRUM 90™

Spectrum 90™Camera
Document: UMAD007298.docm
Revision: A10
Created by: KJB
Date: 27 Sep 2019
IPN: 3041348-A10
Source Location: C:\ePDM\ISLEng\products\ad-spectrum90\manuals\UMAD007298.docm
Page 2 of 19
User Manual
Table of Contents
About This Manual........................................................................................................................................4
Description ....................................................................................................................................................4
Specifications................................................................................................................................................5
Certification...............................................................................................................................................6
Connector Pin-Out....................................................................................................................................6
Laser Lines ...............................................................................................................................................6
Safety............................................................................................................................................................7
System Setup................................................................................................................................................8
Unpacking Components ...........................................................................................................................8
Mounting the Camera ...............................................................................................................................9
Galvanic Corrosion Control.....................................................................................................................10
Connector Handling................................................................................................................................11
SubConn Connector: Lubrication and Cleaning ..................................................................................11
Attaching the Drop Cone Assembly (Optional).......................................................................................12
Flow Thru Cooling (Continuous Purge) ..................................................................................................13
Schrader Valve .......................................................................................................................................13
Nitrogen Purge and Pressurization.........................................................................................................13
Operation.....................................................................................................................................................14
Camera control .......................................................................................................................................14
Pre-Operations Check ............................................................................................................................14
Post-Operations Check...........................................................................................................................15
Troubleshooting ..........................................................................................................................................15
Camera Control Problems......................................................................................................................15
Video Problems.......................................................................................................................................15
Maintenance................................................................................................................................................16
Tether Re-termination.............................................................................................................................16

Spectrum 90™Camera
Document: UMAD007298.docm
Revision: A10
Created by: KJB
Date: 27 Sep 2019
IPN: 3041348-A10
Source Location: C:\ePDM\ISLEng\products\ad-spectrum90\manuals\UMAD007298.docm
Page 3 of 19
User Manual
Rinsing and Cleaning..............................................................................................................................16
Inclinometer Calibration..........................................................................................................................16
Factory Maintenance ..............................................................................................................................17
Parts and Repairs .......................................................................................................................................17
Ordering Parts/Customer Service...........................................................................................................17
Warranty Repairs....................................................................................................................................17
Factory Returns to Canada.....................................................................................................................18
Product/System Drawing Package Availability.......................................................................................18
Limited Warranty Policy ..............................................................................................................................19

Spectrum 90™Camera
Document: UMAD007298.docm
Revision: A10
Created by: KJB
Date: 27 Sep 2019
IPN: 3041348-A10
Source Location: C:\ePDM\ISLEng\products\ad-spectrum90\manuals\UMAD007298.docm
Page 4 of 19
User Manual
About This Manual
This manual has been prepared to assist you in the operation and maintenance of your Eddyfi
Technologies Inuktun equipment. Correct and prudent operation rests with the operator who must
thoroughly understand the operation, maintenance, service and job requirements. The specifications and
information in this manual are current at the time of printing.
This product is continually being updated and improved. Therefore, this manual is meant to explain and
define the functionality of the product. Furthermore, schematics or pictorials and detailed functionality
may differ slightly from what is described in this manual.
Eddyfi Technologies reserves the right to change and/or amend these specifications at any time without
notice. Customers will be notified of any changes to their equipment.
Information in this manual does not necessarily replace specific regulations, codes, standards, or
requirements of others such as government regulations.
This manual copyright © 2019 by Inuktun Services Ltd. All rights reserved.
Description
The Inuktun Spectrum 90™ (SP90) pan-tilt-zoom is an industrial video camera system for use in pipe
inspection systems, harsh industrial environments and underwater. Standard features include 360o
continuous pan, 260 o tilt, zoom and a 60m or 300m depth rating. It is designed to fit into a 120mm ID
space and still be able to tilt and pan throughout its full range. The camera is made from anodized marine
grade aluminum or stainless steel. Installation options include integration into a larger inspection system
(such as a Versatrax 150™ (VT150) pipe inspection system) or independent use as a drop camera or
static system. Typical applications include:
•Toxic environment, confined space or underwater inspections
•Small diameter pipe inspection
•Dam and lock inspection
•Reactor vessel inspection
•Foreign object search and retrieval
•Robotics and remote tooling
•ROV integration
•Remote and/or continuous monitoring
•Drop camera

Spectrum 90™Camera
Document: UMAD007298.docm
Revision: A10
Created by: KJB
Date: 27 Sep 2019
IPN: 3041348-A10
Source Location: C:\ePDM\ISLEng\products\ad-spectrum90\manuals\UMAD007298.docm
Page 5 of 19
User Manual
Specifications
Operating Voltage
36 –70 VDC
Operating Power
65 W Peak
Operating Current
1.8 A Peak
Depth Rating
Standard
60 m (200 ft)
Deep Water
300 m (1000 ft)
Speed
Pan
0 –26 °/s
Tilt
0 –9 °/s
Range
Pan
360 ° Continuous
Tilt
260 ° (+/- 130 ° )
Dimensions
Standard
90 x 273 mm (3.5 x 10.8 in)
Deep Water
90 x 298 mm (3.5 x 11.7 in)
Weight
Aluminum
2.8 kg (6.1 lb)
Stainless Steel
5.5 kg (12.2 lb)
Imager
Sensor
1/2.8in Exmor R CMOS (NTSC or PAL)
Lens
f = 5.1 to 51 mm
120x Zoom (10x Optical, 12x Digital)
Focus
Manual or Auto
Horizontal Resolution
720 TVL
Minimum Illumination
0.5 lux
HFOV
54° (air)
Depth of Field
10 mm (0.4in) to infinity
Lights
3 x High intensity LEDs
Lasers (optional)
2 x Laser Lines, 635 nm, 30 mm (1.18 in) Spacing
Controls
Pan, tilt, zoom, focus, lights, lasers, exposure
Maximum Tether Length
500 m (1,650 ft)
Operating Temperature
0 –50 ºC (32 –122 ºF)
Storage Temperature
-20° –60 ºC (-4 –140 ºF)

Spectrum 90™Camera
Document: UMAD007298.docm
Revision: A10
Created by: KJB
Date: 27 Sep 2019
IPN: 3041348-A10
Source Location: C:\ePDM\ISLEng\products\ad-spectrum90\manuals\UMAD007298.docm
Page 6 of 19
User Manual
Certification
The product is built in accordance with:
Machinery Directive 2006/42/EC, and
Electromagnetic Compatibility Directive 2004/108/EC and Directive 2014/30/EU
Connector Pin-Out
The Spectrum 90™ connects to power and communications through a Subconn MCBH8M connector on
the back of the camera. Note: Pin-out is shown for the Bulkhead Connector on the camera.
Pin
Function
1
70 VDC GND (-)
2
70 VDC (+)
3
RS485A (+)
4
RS485B (-)
5
SpareA
6
SpareB
7
Video1 (+)
8
Video1 (-)
FIGURE 1: CONNECTOR PIN-OUT
Laser Lines
The Spectrum 90™ camera may be optionally equipped with vertical laser lines (red Class 2 lasers at 635
nm, 1.5 mW). Laser line separation is 30mm (1.18 in).
•CAUTION: Class II Laser: Do not intentionally stare
into the beam. Typically, Class II relies on the blink
reflex to limit exposure to no more than ¼-second.
Intentionally staring into the beam can cause eye injury.
•When performing maintenance or functional checks of
the lasers and camera lights, take precautions to protect
nearby personnel from unintended exposure which
could be temporarily blinding.

Spectrum 90™Camera
Document: UMAD007298.docm
Revision: A10
Created by: KJB
Date: 27 Sep 2019
IPN: 3041348-A10
Source Location: C:\ePDM\ISLEng\products\ad-spectrum90\manuals\UMAD007298.docm
Page 7 of 19
User Manual
Safety
In order to be able to use this product properly and safely, every user must first read these operating
instructions and observe the safety instructions contained therein. Take care of these operating
instructions and keep them in a place where they can be accessed by everyone.
CAUTION: Failure to follow these safety instructions may result in injury or
equipment damage.
WARNING: High Voltage 36-70 VDC. If the equipment is powered from a
source other than an Eddyfi Technologies provided controller, the power supplied
to the product must have reinforced isolation from the mains with no reference to
earth ground.
WARNING: Spark Hazard - Under no circumstances should this equipment be
used in a potentially explosive atmosphere.
WARNING: Intense Optical Radiation - The Spectrum 90™ camera lights are
extremely bright. Never look directly at the lights. Use a welding filter (shade #8
or higher) if inspecting the LEDs.
•CAUTION: Class II Laser: Do not intentionally stare into
the beam. Typically, Class II relies on the blink reflex to limit
exposure to no more than ¼-second. Intentionally staring
into the beam will cause eye injury.
•When performing maintenance or functional checks of the
lasers and camera lights, take precautions to protect
nearby personnel from unintended exposure which could
be temporarily blinding.
•The Spectrum 90™camera is an industrial product. All personnel operating or maintaining this
equipment must be competently trained.

Spectrum 90™Camera
Document: UMAD007298.docm
Revision: A10
Created by: KJB
Date: 27 Sep 2019
IPN: 3041348-A10
Source Location: C:\ePDM\ISLEng\products\ad-spectrum90\manuals\UMAD007298.docm
Page 8 of 19
User Manual
•There are no user serviceable parts inside. This product may be serviced only by qualified
technicians or trained personnel.
•Edddyfi equipment is used in many varied environments from hot/dry to confined spaces to deep
underwater. Such diverse environment risks must be addressed by the operators who are trained
to work in such surroundings. As such, the operator is responsible to determine safe site setup
and appropriate personal protective equipment (PPE) for operation and maintenance of the
equipment.
•Do not use the product or any component exposed to pressures higher than the rated working
pressure.
In addition, observe the following precautions when cleaning or servicing the Spectrum 90™ camera:
•Do not operate the camera with a damaged connector or cable. Inspect connectors and cables
regularly for damage.
•Call the Eddyfi Technologies service department for assistance or service if needed.
CAUTION: Disconnecting the camera while the power is on can cause damage to
the camera. Disconnect the power source before servicing the product.
CAUTION: Do not over-pressure the camera through the Schrader valve.
Applying pressure beyond 15 psi through the Schrader valve may cause the
camera to burst resulting in injury and equipment damage. When re-purging, use
a regulated, gauged supply and apply no more than 10 psi pressure.
System Setup
Unpacking Components
The Spectrum 90™ camera is shipped in a rugged case or is installed on an integrated system.
Packaging is selected to protect the camera from damage during shipping or storage. Upon receiving
your system, check the case and contents for any damage that may have occurred during transport.
Should any of these components be missing or damaged, please notify your vendor. We suggest that
when the system is re-shipped or stored for any length of time, it should be re-packaged in its original
case or be put in a cardboard box encased in high-density foam. It is also strongly advised that the case
be placed in a cardboard box again for shipping purposes. This measure greatly reduces rough handling
and subsequent shipping damage.
CAUTION: The Schrader cap installed on your camera is a proprietary cap
rated to 300 m (1000 ft) depth. Do not install any other Schrader cap. Doing
so may result in flooding and destruction of the camera or in personal injuries
from electrical shorts. Standard automotive style Schrader valve components
will be forced open below 40 m (130 ft) depth by the water pressure.

Spectrum 90™Camera
Document: UMAD007298.docm
Revision: A10
Created by: KJB
Date: 27 Sep 2019
IPN: 3041348-A10
Source Location: C:\ePDM\ISLEng\products\ad-spectrum90\manuals\UMAD007298.docm
Page 9 of 19
User Manual
Mounting the Camera
The Spectrum 90™ camera can be mounted at the back plate using the three threaded M6x1 x 13mm
deep blind holes. These holes are also utilized for mounting the optional drop cone. Use M6x1 SS SHCS.
The length of the screws will depend on the thickness of the mounting bracket. Refer to the figures below.
The camera may be mounted in any orientation as the camera has continuous pan.
Alternatively, the cameras may be mounted by a clamp around the 89 mm (3.5 in) diameter stationary
portion of the barrel. Note the standard (60 m / 200 ft) and deep water (300 m / 1000 ft) cameras are
different lengths as illustrated.
CAUTION: Avoid forcing the TILT or PAN mechanisms by hand. It will wear the
clutch discs and could cause premature failure.
FIGURE 2: SPECTRUM 90™ STANDARD CAMERA MOUNTING DIMENSIONS

Spectrum 90™Camera
Document: UMAD007298.docm
Revision: A10
Created by: KJB
Date: 27 Sep 2019
IPN: 3041348-A10
Source Location: C:\ePDM\ISLEng\products\ad-spectrum90\manuals\UMAD007298.docm
Page 10 of 19
User Manual
FIGURE 3: SPECTRUM 90™ DEEP WATER CAMERA MOUNTING DIMENSIONS
Galvanic Corrosion Control
We strongly recommend stainless steel cameras for salt water environments or other corrosive
environments. The camera warranty is conditional when aluminum body cameras are deployed in these
kinds of applications.
Cathodic protection is required whenever the camera is being deployed in a salt water environment,
either submerged or in salt spray, regardless of camera material.
Eddyfi Technologies Inuktun cameras use aluminum marine anodes for both stainless and aluminum
cameras. Aluminum anodes are common in the marine industry and are replacing zinc anodes in many
areas. For cameras systems that are often pulled in and out of the water, aluminum anodes are especially
important, as zinc anodes tend to scale over when exposed to air and may not reactivate when
submerged again. An aluminum anode will always reactivate.
It is required that the structure to which the camera is mounted also be protected by aluminum anodes.
If the structure is of a dissimilar metal, the camera mount must be isolated from the structure. Do not mix
anode types (zinc and aluminum) on the assembly. There must be only one anode type throughout the
structure. Magnesium anodes must never be used with Spectrum™ camera installations.
Anodes are installed onto the camera as illustrated below. The small anode is installed onto the mounting
bracket using an M5 x 10mm 316 SS SHCS. A large disk anode is attached to a mounting bracket for the
base using an M6 x 12mm 316 SS SHCS. Contact your sales representative for replacements.