edelkrone TARGET User manual
TARGET MODULE
Before operating your edelkrone,
please watch the users manual video.
USER’S MANUAL
TABLE OF CONTENTS
WHAT’S IN THE BOX & THE BASICS.
MOUNTING YOUR TARGET MODULE TO YOUR SLIDERPLUS
TARGET GROUND MODE
TARGET TRIPOD MODE
PANAROMIC MODE
AUTO PAN MODE
CAUTIONS AND TIPS
1.
2.
3.
4.
5.
6.
7.
1. WHAT’S IN THE BOX & THE BASICS
1
10
2
3
4
8
9
5
611
7
15
13
12
14
Target Encoder Module
DC socket
Screen
Control button
On/O switch
1/
2/
3/
4/
5/
6/
7/
8/
9/
10/
Data Port
Motion control belt
Target pan/tilt module
Data port
AC-DC adaptor*
11/
12/
13/
14/
15/
Allen wrench
Attachment screws
Battery bracket screws
Data cable
Battery bracket
*The shape of the plug adapter varies with the country or region
2. MOUNTING YOUR TARGET MODULE TO YOUR SLIDERPLUS
1/
2/
3/
4/
Attach the motion control belt.
Place the Target Module on the
end of the SliderPLUS.
Use the thumb screws to tighten the
module in place.
If the Target Module is going to be
powered by batteries, place the battery
bracket in its position & attach the screws.
Place the Target Pan/Tilt Module in its position and
tighten it.(Be sure that data port of the Target Head
is placed on the same side as the lock of the
SliderPLUS.
Connect the data cable to data ports of the Target
Encoder Module and Target Pan/Tilt Module.
5/
1
2
3
6
4
5
6/
*Detailed video explaining how to attach this belt and mountaing details can be found
from : manuals.edelkrone.com
Detailed video explaining how to attach this belt and mountaing details can be found
from : manuals.edelkrone.com
SET TO
00
1. Use LEFT/RIGHT buttons to make your lens perpendicular to the slider rails. Then press OK.
3. “TARGET GROUND MODE”
2. Use LEFT/RIGHT buttons to turn the Target Pan/Tilt head to your target. Then use a measurement tool to
measure the distance between the Target Head and your target. To enter the distance use UP/DOWN buttons.
Then press OK to proceed.
While measuring the distance please be sure to measure from the Target Head’s middle point as shown in
the gure above to get the perfect results.
3. When you see the :”TARGET ACTIVE”on the screen you can start your slides. Target Module responds to
your slides and it keeps your target in the frame automatically. The speed of the Target Head will depend on
the speed of your slide.
CM:50
IN: 19,6
TARGET
ACTIVE
In Target Ground Mode you can lock onto your target while using the SliderPLUS on its feet.
For this mode, put your SliderPLUS on a at surface and select the mode by pressing OK, then follow
the steps below to lock on your target.
50 cm
4. 5. ”PANORAMIC MODE”
“TARGET TRIPOD MODE”
SliderPLUS could travel twice its own length when
it is mounted on a tripod. That is the only dierence
between Target Tripod Mode and Target Ground
Mode. So while using on a tripod please be sure to
follow the same steps with the Target Ground Mode.
In Panoromic Mode Target Module will perform a convex movement as shown in the gure. Turn o and
turn on the system in order to navigate between modes. Select the Panoromic mode, then follow the steps
below. In Panoromic Mode you don't need to make the Target Head perpendicular to the rails of the
SliderPLUS.
Be careful when following objects above or
below the horizon. This can cause a Dutch
angle.
SET TO
00
1. Use LEFT/RIGHT buttons to choose your start angle. Then press OK.
2. Use UP/DOWN buttons to set the amount of degrees to turn per centimeter. Use LEFT/RIGHT buttons to
change cm to inch.
3. Panoram. slide means system is active now. You
can start your slide and the Target Head will turn.
DEG/CM
8.0
PANOROM.
SLIDE
If the value is entered negative, Target Head will turn in the opposite direction.
*Before operating your product, please watch the users manual videos from the link:
manual.edelkrone.com
*Before operating your product, please watch the users manual videos from the link:
manuals.edelkrone.com
*Before operating your product, please watch the users manual videos from the link:
manual.edelkrone.com
*Before operating your product, please watch the users manual videos from the link:
manuals.edelkrone.com
6.
Notice
”AUTO PAN MODE”
Auto pan mode is not a responsive mode so it could be triggered wthout sliding your SliderPLUS.
SET TO
00
1. Use LEFT/RIGHT buttons to choose your start angle.
Then press OK.
2. Use UP/DOWN buttons to set the amount of degrees of turn for each seconds. Then pres OK.
3. Use UP/DOWN buttons to set the range of the turn.Then press OK.
DEG/SEC
10.0
RANGE
DEG:120
4. It will start panning and let you know once it has completed.
AUTO
PANNING
*Before operating your product, please watch the users manual videos from the link:
manual.edelkrone.com
*Before operating your product, please watch the users manual videos from the link:
manuals.edelkrone.com
7. CAUTIONS & TIPS
Use fully charged batteries or
AC-DC adaptor to get better
results.
Do not attempt to disassemble
to the module to protect your
warranty.
Hot swapping : It is possible to
change a battery while
powering the module with
another battery.
To adjust the tension of the tilt on the Target
Head, tighten/loosen the 2 screws on the head
as shown below.
Rotating the Target Head manually is not
recommended. If you need to rotate please
be sure the data cable is unplugged.
*Before operating your product, please watch the users manual videos from the link:
manual.edelkrone.com
*Before operating your product, please watch the users manual videos from the link:
manuals.edelkrone.com
Target Module work great with the Action Module to make super steady shots. Action Module
helps the Target keep its position.. This add on is sold separately.
Target Module has a really important add on called L bracket. Information about L Bracket can
be found on its own manual videoes and users manual sheets. This add on is sold separately.
Add On: Action Module
Add On: L Bracket
*Before operating your product, please watch the users manual videos from the link:
manual.edelkrone.com
*Before operating your product, please watch the users manual videos from the link:
manuals.edelkrone.com
DISPOSAL OF THE PRODUCT
DISCLAIMER
Should the product become damaged beyond repair, or if you wish to dispose it, it must be disposed
separately from the municipal waste stream via designated collection facilities appointed by the
government or the local authorities. Observe the regulations of your area and country that relate to
the disposal of electronic products.
edelkrone cannot be responsible for damage caused by improper use or modication of the product.
►Keep your electronic Motion Control Unit away from all sorts of liquids.
►In order to preserve your Motion Control Unit and battery performance at their best, use exact same type of
batteries with equivalent level of charge during dual-battery operation.
►Do not attempt to disassemble or modify any internal parts of your Motion Control Unit. If the device appears to
be malfunctioning, discontinue use immediately and contact support for qualied service.
►Never force a dierent type of connector into a port.
►Never use or store your Motion Control Unit in areas subject to extreme temperatures, or high levels of vibration.
►If your motion control unit becomes unresponsive, disconnect and re-connect the power source. Make sure your
AC/DC adapter is plugged in or your batteries are properly charged. If the problem persists, contact
our support team.
►Environmental factors may aect your Motion Control Unit’s performance. Keep your product away from
environmental hazards such as dust or heavy resonance. Do not use chemical materials to clean your product.
►Only use included battery plate, AC/DC adapter or equivalent power sources. Use of an inappropriate power
source may permanently damage your Motion Control Unit.
►If there is an impairment on the power or connector cable, stop using the Motion Control Unit immediately.
►Avoid dropping or causing physical damage to your Motion Control Unit.
►Do not place heavy objects on top of your Motion Control Unit.
© 2016, edelkrone www.edelkrone.com
