Edge Tub Elite User manual

v 1.0
The Edge Tub Elite User Manual

PAGE - 01
WARNINGS
PAGE - 02
CONTROL PANEL
PAGE - 03
PARTS REFERENCES
PAGE - 05
SETUP INSTRUCTIONS
PAGE - 08
WIFI  APP SETUP
PAGE - 11
TAKEDOWN INSTRUCTIONS
PAGE - 13
WATER MAINTENANCE
PAGE - 14
RECOMMENDED ROUTINE MAINTENANCE
PAGE - 15
TROUBLESHOOTING
PAGE - 17
LIMITED WARRANTY
PAGE - 18
RECOMMENDED ACCESSORIES
TABLE OF CONTENTS
EDGETHEORYLABS.COM
EDGE TUB USER MANUAL

YOU MUST CONSULT WITH A MEDICAL PROFESSIONAL to ensure you are
medically fit prior to using your Edge Tub. It is important you understand
the relevant risks, seriousness of risks and potential consequences of using
the tub, either with cold or hot water. As with any receptacle for water, there
is the risk of drowning which can be fatal. It is your responsibility to ensure
minors are always properly supervised in the Edge Tub and anyone who
enters can safely stay above water. The Edge Tub should never be used when
impaired under any substance, which could aect your ability to remain
awake, conscious and operating with a clear mind. With cold water, there is
the risk of hypothermia and anyone using the tub should exercise extreme
caution and sensible judgment to exit the Edge Tub before the onset of any
such complications. Extreme caution should be used because as your body
becomes colder, movements and circulation in your body may slow down.
The use of the Edge Tub with hot water can result in nausea, dizziness and
light-headedness. Caution and sensible judgment must be used to prevent any
such side eects. Always leave the tub before you are experiencing any such
symptoms. You also understand that by using the Edge Tub, you will be solely
responsible for its hygiene, sanitation and maintenance. The Edge Tub is only
to be used for the explicit purpose of being a recreational cold or hot tub and
for no other purposes. The best way to avoid any of the risks of using the Edge
Tub is to remain aware of how you are feeling and err on the side of caution.
WARNING:
This product can expose you to chemicals including lead, which is known to the
State of California to cause cancer.
For more information, go to www.P65Warnings.ca.gov
DROWNING
• To reduce the risk of injury, do not permit children to use this product unless
closely supervised at all times.
• Risk of Accidental Drowning. Extreme caution must be exercised to prevent
unauthorized access by children.
• Tub Cover is not a Safety Cover.
ELECTRICAL
• This product is provided with a ground-fault circuit-interrupter integrated. The
GFCI must be tested before each use. To perform the test, first ensure the blue
Power Switch on the back of the Chiller is up in the “on” position and then press
the orange “T” Test Button above the Power Switch. The Power Switch should flip
to the down “o” position. Now flip up the Power Switch to the “on” position. If
this test does not cause the Power Switch to turn o, do not proceed, and contact
support for assistance. DO NOT USE IF THIS TEST FAILS.
• Do not handle electrical outlet with wet hands.
• Do not permit any electric appliance within 5 feet of this product.
• Only use this product with 120v/60hz electrical circuit; outlet must be grounded
appropriately.
• Never submerge machine or expose to direct water spray.
HEALTH
• Elderly persons, pregnant women, infants, and those with health conditions
requiring medical care - especially cardiovascular and neurological - should
consult with a physician before using this product.
• Hot and Cold Water Immersion while under the influence of alcohol, narcotics,
drugs or medicines may lead to serious injury and is not recommended.
• Do not use alone.
• Long exposure may result in hyper or hypothermia, nausea, dizziness, or fainting.
• Do not exceed 5 minutes in cold or 30 minutes in hot water; excessive exposure
may be harmful to health.
• Always enter and exit the tub slowly and cautiously. Wet surfaces are slippery.
ADVISORY:
• Pool owners may need to comply with local or state laws relating to childproof
fencing, safety barriers, lighting, and other safety requirements. Customers
should contact their local building code enforcement oice for further details.
• Keep hair, fingers, towels, and other items away from the fan.
• Only professional technicians may work on the system.
PAGE - 01
EDGETHEORYLABS.COM
WARNINGS
EDGE TUB USER MANUAL

PAGE - 02
EDGETHEORYLABS.COM
CONTROL PANEL
1 - POWER BUTTON
Press for 2 seconds to turn the Chiller
On or O.
5 - UP ARROW
Press to increase temperature aer
pressing Setting Button.
12 - COOL/HEAT SYSTEM INDICATOR
Shows if Chiller is actively cooling
(“Cool”), heating (“Heat”), or on
standby (blank).
8 - SET TEMPERATURE
Shows the desired temperature
setting for the Tu b .
2 - MODE BUTTON
Press for 5 seconds to switch between
Fahrenheit and Celsius.
6 - DOWN ARROW
Press to decrease set temperature
aer pressing Setting Button.
13 - COMPRESSOR STATUS
Shows when compressor is running.
9 - WATER FLOW INDICATOR
Shows the water flow of Chiller in
liters per minute.
3 - SETTING BUTTON
Press for 1 second to change
temperature setting.
5 + 6 - CHILD LOCK
Press both for 5 seconds to engage
Child Lock.
14 - WIFI INDICATOR
Shows Wifi status. Solid for
connected, blinking for setup mode.
Blank for disconnected.
10 - MODE INDICATOR
Shows mode Chiller is operating in
(“Default” is normal function).
4 - WIFI ACTIVATION BUTTON
Press for 5 seconds to engage WiFi
setup mode.
7 - TUB TEMPERATURE
Shows temperature of water coming
from the Tub.
11 - DEFROST INDICATOR
Shows if Chiller is defrosting. Will
display “On” or “O.”
System
S W
Set
T1
L
Defrost
Mode
Default
OOn
Cool Heat
43.5
40.0
17.5
F
F
1
9
2
10
3
11
4
12
5
13
6
14
7
8
EDGE TUB USER MANUAL

PAGE - 03
EDGETHEORYLABS.COM
PARTS REFERENCES
CHILLER
The main unit which chills/heats, circulates, and filters the water.
CHILLER DRAIN
The drain with cap at the middle bottom on the rear of the chiller. This is meant
to be opened to allow the machine to drain water out when the Chiller is being
moved or packaged.
PROTECTIVE CAPS
The protective caps that thread on the Chiller Inlet and Outlet ports.
CHILLER HOSES
The flexible hoses are used to flow water from the Edge Tub to the Chiller.
• Hose Connection Fittings
The fittings on the end of each hose. They connect the Chiller Hoses to the
Chiller Inlet/Outlet and Tub Valve Fittings.
• Hose O-Rings
The o-rings in the hose connections. These are vital for water-tight and air-
tight connections with the Chiller Hoses and Tub or Chiller.
CHILLER INLET (RED)
The connection on the chiller, which incoming water enters through. This is
marked with a red ring.
CHILLER FRONT CHILLER BACK
CHILLER OUTLET (GREEN)
The connection on the chiller, which outgoing water leaves through. This is
marked with a green ring.
CONTROL PANEL
The visual readout including Tub Temperature, Set Point, and the Control
Buttons (detailed in Control Panel section).
DOUBLE ACTION AIR PUMP
The air pump to inflate and deflate the Edge Tub.
EXTERNAL WATER STRAINER
The assembly of parts that is used to prevent any debris from entering the
Chiller. It connects to the Chiller Inlet (red) and is made up of the Water Strainer
Cover, Strainer O-Ring, and Inner Water Strainer.
• Inner Water Strainer
The cylindrical mesh element that attaches to the Chiller Inlet (red).
• Strainer O-Ring
The o-ring at the base of the External Water Strainer connection (red) on
the Chiller.
• Water Strainer Cover
The metal cover that will screw on the Chiller Inlet (red) over the Inner
Water Strainer.
CHILLER DRAIN
CHILLER OUTLET
UPPER WATER FILTER HOUSING
LOWER WATER FILTER HOUSING
CONTROL PANEL
CHILLER INLET
EDGE TUB USER MANUAL
System
SW
Set
T1
L
Defrost
Mode
Default
On
Cool Heat
43.5
40.0
17.5
F
F

PAGE - 04
EDGETHEORYLABS.COM
PARTS REFERENCES
INFLATION VALVE
The port used to inflate the Edge Tub with the Double Action Air Pump. Includes
the Inflation Valve Cap, and Inflation Valve Pin.
• Inflation Valve Pin
The spring loaded component of the Inflation Valve that is exposed when
the Inflation Valve Cap is removed.
MEASURING CUP
This is a 30cc measuring cup to use for sanitizer and oxidizer dosing.
OXIDIZER
This Sirona Simply Oxidizer is part of the water maintenance protocol for the
water in the tub. Refer to the maintenance instructions for proper use.
TUB
The inflatable tub.
TUB COVER
The lockable cover for your tub.
• Locking Buckles
The locking buckles on the tub cover that fasten and lock the cover to the
tub when not in use.
VALVE FITTING
The connection elbow/valve that connects the Tub Fittings to the Chiller Hoses
running from the chiller. The parts of the Tub Valve Fitting are the Threaded
Collar, Elbow, and Valve.
• Elbow
The 90 degree section of pipe connecting the Connection Ring and the Valve.
• Threaded Collar
The female rotating threaded component on the Tub Valve Fitting that
connects to the Tub Fitting.
• Valve
The stainless steel valve that controls water flow.
WATER FILTER HOUSING
The assembly which houses the Water Filter. Includes the Upper Water Filter
Housing and Lower Water Filter Housing.
• Filter Housing O-ring
The filter housing o-ring is located in the Upper Water Filter Housing and is
used to create an air tight connection between the Lower and Upper Water
Filter Housings.
• Filter Housing Wrench
The wrench designed to be used when the Lower Water Filter Housing is too
tight to loosen by hand. Do not use the wrench to tighten the filter housing
when setting up or changing the filter.
• Lower Water Filter Housing
The filter housing which holds the water filter and connects to the back of
the chiller (lower clear part).
• Upper Water Filter Housing
The water filter housing connection point (upper white part) on the rear of
the chiller.
• Water Filter
The water filter is used to filter debris from the water running through the
chiller. This is placed into the Lower Water Filter Housing.
EDGE TUB USER MANUAL

PAGE - 05
EDGETHEORYLABS.COM
SETUP INSTRUCTIONS
STEP 1) UNBOX YOUR CHILLER AND TUB
Remove the Chiller and Tub from their shipping cartons. We recommend
keeping the Chiller box for future transportation needs. Select a flat, clean and
smooth surface. A water source and 120v power source should be accessible. If
outdoors, we recommend setting the tub up in a sheltered area for longevity of
your product. If using a Protection Mat, first place the mat down and unfold the
Tub in desired orientation.
STEP 3) INFLATE THE TUB
Inflate the Tu b with the Double Action Air Pump. Ensuring the hose is connected
to the “Inflate” side of the pump. Open the Inflation Valve on the Tub by
rotating counterclockwise. The Inflation Hose connects to the Inflation Valve
with a quarter turn clockwise. When inflating the Tu b, check to ensure that the
Inflation Valve Pin is in the depressed (out) position or the air will be released
aer the hose is detached. Inflate until the gauge reads 10 PSI. Do not over
inflate or product damage will occur. Replace the Inflation Valve cap with a
clockwise turn.
STEP 2) INSTALL THE VALVE FITTINGS
Attach the Valve Fittings to the Tub “water out” (red), and “water in” (green)
fittings by rotating it clockwise until hand tight. Do not tighten with tools. The
Valve Fittings should be oriented as shown.
STEP 4) INSTALL THE EXTERNAL WATER STRAINER
Remove the Protective Cap of the red “Inlet” fitting on the Chiller by rotating
counterclockwise. Install the Inner Water Strainer into the red “Inlet” by turning
clockwise. Next, install the silver Water Strainer Cover. This fits over the Inner
Water Strainer and should be screwed to hand tight.
INFLATE
INFLATE
SETUP:
Detailed setup videos can be found here.
https://www.edgetheorylabs.com/pages/edge-support
OUT
✓X
IN
EDGE TUB USER MANUAL

PAGE - 06
EDGETHEORYLABS.COM
SETUP INSTRUCTIONS
STEP 5) CONNECT THE CHILLER TO THE TUB
First check that there is a Hose O-Ring inside each of the four Hose Connection
Fittings. If not, place an o-ring from the spare parts bag. The green “Water In”
fitting on the Tub should connect to the green “Outlet” on the Chiller. The red
“Water Out” fitting on the Tub should connect to the red “Inlet” on the Chiller.
To tighten, thread on the Hose Connection Fittings and rotate clockwise. The
threads should tighten easily and smoothly. If resistance is felt, try attaching the
hose again. Hand tighten only. Overtightening may cause leaking or damage.
STEP 7) OPEN VALVES
Once the Tub has been filled, confirm the Tub Valve Fittings are in the open
(parallel) position. Ensure this step has been completed to prevent damage
to Chiller!
STEP 6) FILL THE TUB
Check that the Chiller Drain Cap and hoses are in place. Remove the Lower
Water Filter Housing, insert a filter and fill with water. Ensure the Filter Housing
O-Ring is in place in the Upper Water Filter Housing. Install the Lower Water Filter
Housing by turning right if facing the back of the Chiller until hand tight. Do not
use the filter wrench to tighten the water filter housing (for loosening only). The
Tub can now be filled with water up to “Fill Level” line. Overfilling may cause
water to overflow from the Tub for some users, though you may fill to your
preference.
STEP 8) POWER ON THE CHILLER
Plug the Chiller into a standard 120v grounded power supply with 15 amp
minimum circuit and test the GFCI functionality. To perform the test, first
ensure the Power Switch on the back of the Chiller is up in the “on” position
and then press the orange “T” Test Button above the Power Switch. The Power
Switch should flip to the down “o” position. Now flip the Power Switch back
up to the “on” position. If this test does not cause the Power Switch to turn o,
do not proceed, and contact support for assistance. Place the Power Plug in an
elevated position o the ground and away from water. Do not handle with wet
hands. You may now turn on the Chiller by pressing the “Power On” button on
the display screen. The Chiller may take up to 2-3 minutes to purge air from
the system and will flash “o1.x” or “02.x” while purging. Once this has been
completed, this code will change to the current water temperature and the
Chiller will begin cooling or heating. If the “FL” (Flow) error appears, or if this
step takes longer than 2-3 minutes, check that the Valves are open, and that the
hose connections and filter housing are connected properly, and then repeat
this step.
✓X
SETUP:
Detailed setup videos can be found here.
https://www.edgetheorylabs.com/pages/edge-support
EDGE TUB USER MANUAL

PAGE - 07
EDGETHEORYLABS.COM
SETUP INSTRUCTIONS
SETUP:
Detailed setup videos can be found here.
https://www.edgetheorylabs.com/pages/edge-support
STEP 9) CHOOSE YOUR TEMPERATURE
To change the set temperature, press and hold the “S” key for 1 second until
the set temperature flashes. Use the up or down arrows to set your desired
temperature. Press the “S” key once more to lock the setting and stop the set
temperature flashing. Your Tu b will reach minimum or maximum temperature in
about 3 hours depending on ambient temperature and set temperature.
STEP 11) COVER YOUR TUB
Finally, put the Cover on if the Tub will not be immediately used, and secure
the four Locking Buckles. Use of Buckle Combination Lock is recommended
for all users, but especially for those with children. To set combination of
Locking Buckles:
A. The original code is preset to “00.”
B. To change or set:
1. Locate the pin in the side, depress the pin with a jewelers screwdriver, pen
or toothpick.
2. While still depressing the pin, rotate the dial to your desired number.
3. If a number wheel gets stuck aer you adjust the code, push the pin on the
opposite side to release the wheel.
4. Do this for each side, one for each number.
5. Repeat above for each buckle.
STEP 10) STARTUP WATER SANITATION
Prior to use, the water should be treated with the startup Sanitizer dose.
The startup dose is below and should be used any time the water is replaced
in the Tub.
A. Add 60cc (2 Measuring Cups) of Oxidizer into water.
B. Wait 15 minutes.
C. Add 15cc (½ Measuring Cup) of Sanitizer into water.
D. Wait 15 minutes before use.
Please refer to Maintenance Instructions for weekly water maintenance protocol.
ENJOY YOUR NEW EDGE ELITE TUB
Please watch the Water Maintenance Instructional video for the weekly protocol
you need to follow to ensure the water stays clean and clear. Enjoy!
EDGE TUB USER MANUAL

PAGE - 08
EDGETHEORYLABS.COM
WIFI / APP SETUP
SETUP:
Download and install the Tuya Smart application by scanning the QR code.
Apple: https://apps.apple.com/us/app/tuya-smart/id1034649547
Android: https://play.google.com/store/apps/details?id=com.tuya.smart&hl=en_US&gl=US
STEP 1)
Ensure the device you are using is connected to the WiFi network that you wish
to connect the Chiller to, and open the Tuya Smart application.
Important Note: The Tuya Smart system only works with 2.4 GHz wireless
networks. Many wireless networks utilize 5 GHz and may need to be configured
at 2.4 GHz. Please contact the manufacturer of your Wi-Fi router for support on
this matter if you experience trouble.
STEP 3)
Once the Tuya Smart app is open,
you may add the Chiller by selecting
“Add Device” on the home screen.
STEP 2)
Now you may turn on the Chiller if not already. Press and hold the “W” button
for 5 seconds until the Wi-Fi indicator on the display flashes.
STEP 4)
The app should recognize the Chiller
automatically. If not, from the menu,
select “Small Home Appliance” on
the le sidebar menu and then select
“Thermostat (Wi-Fi).”
EDGE TUB USER MANUAL

PAGE - 09
EDGETHEORYLABS.COM
WIFI / APP SETUP
STEP 5)
Next, the Wi-Fi Network screen will
prompt to confirm the wireless
network and request the password
for the network.
STEP 7)
Your Chiller should now be
connected successfully!
STEP 6)
The app will now attempt to connect
to the Chiller. This may take up to
2 minutes. If the attempt fails, you
will be asked to retry. Retry, and if it
fails again, ensure you’re using a 2.4
GHz wireless band and that network
name and password are correct.
SETUP:
Download and install the Tuya Smart application by scanning the QR code.
Apple: https://apps.apple.com/us/app/tuya-smart/id1034649547
Android: https://play.google.com/store/apps/details?id=com.tuya.smart&hl=en_US&gl=US
EDGE TUB USER MANUAL

PAGE - 10
EDGETHEORYLABS.COM
APP TIMER INSTRUCTIONS
STEP 1)
Open the Tuya app and navigate to the timing control option. Open the timing
control page.
STEP 2)
Set the desired time and desired settings, then press “save.”
SETUP:
Download and install the Tuya Smart application by scanning the QR code.
Apple: https://apps.apple.com/us/app/tuya-smart/id1034649547
Android: https://play.google.com/store/apps/details?id=com.tuya.smart&hl=en_US&gl=US
EDGE TUB USER MANUAL
SET TIME
SELECT TIMING CONTROL
SET REPEAT IF DESIRED
SET ACTION DESIRED (ON OR OFF)

PAGE - 11
EDGETHEORYLABS.COM
TAKEDOWN INSTRUCTIONS
STEP 1) TURN THE CHILLER OFF
Turn the Chiller o by toggling the Power Switch on the back of the Chiller to the
down “o” position.
STEP 3) DRAIN THE TUB
There are three methods that can be used to drain the Tub:
A.Disconnect the red “Water In” hose from the Chiller. Direct the hose to the
desired area for drainage and open the valve. Water will flow out of the hose
until it reaches the Lower Water Fitting. The remaining water can be removed
by turning the tub over.
B.Disconnect both hoses from the Tub . The red “Inlet” hose from the Chiller
should be placed inside the tub. The green “Outlet” hose from the Chiller
should be directed to the desired location for drainage and the Chiller can be
turned back on. The Chiller will pump water out. The Tub can be tipped as the
water level gets low to remove the last bit of water. Be sure to turn o
the Chiller immediately when the Tu b has been drained to avoid damaging
the Chiller.
C.Purchase a submersible Sump pump. Connect your garden hose to the
pump and drop the pump into the water. When you plug the pump in,
water will begin draining. Please visit our help center or reach out for
recommendations on Sump pumps.
STEP 2) CLOSE THE VALVES
Turn the Tub Valve Fittings to the closed (perpendicular) position (see image).
STEP 4) DISCONNECT THE HOSES
Once the Tub is drained, the hoses can be disconnected from the Tu b and Chiller
by rotating the Hose Connection Fittings counterclockwise, and the Chiller can
be unplugged.
TAKEDOWN:
Detailed takedown videos can be found here.
https://www.edgetheorylabs.com/pages/edge-support
✓X
STEP 5) DRY THE TUB
The Tub should now be dried inside and out (including bottom) with a towel
to prevent mildew. This is also a good time to clean the Tub with mild soap
and water.
EDGE TUB USER MANUAL

OUT
X
PAGE - 12
EDGETHEORYLABS.COM
TAKEDOWN INSTRUCTIONS
STEP 7) FOLD THE TUB
The Tub can now be folded for storage. First fold the branded “Edge Theory
Labs” wall of the Tub inward. The back wall of the Tub can now be folded over
the branded side of the Tu b so that the tub is flat. Fold the right side of the Tub
towards the center, with the fold being just outside the water fitting, and repeat
on the le side. Hold the tri-folded Tub with one hand, and with the other, place
the Storage Strap under the Tu b. Fasten the Storage Strap and tighten (see
images).
STEP 6) DEFLATE THE TUB
Remove the Inflation Valve Cap. Press the Inflation Valve Pin to allow the air to
be released. The air release will be aggressive so don’t be startled! Remove the
remaining air by attaching the Inflation Hose to the “Deflate” side of the Double
Action Hand Pump. When deflating the Tub , check to ensure that the Inflation
Valve Pin is in the depressed (out) position (see image). Deflate until all air has
been removed and remove the inflation hose. Replace the Inflation Valve Cap.
The Tub Valve Fittings should be removed.
STEP 8) PACK THE TUB
Place the Tub, Cover, Hoses, and Double Action Air Pump into the backpack. This
is best done by starting with the Tub , then the Tub Cover, then Double Action Air
Pump, and finally the Hoses.
TAKEDOWN:
Detailed takedown videos can be found here.
https://www.edgetheorylabs.com/pages/edge-support
DEFLATE
DEFLATE
STEP 9) DRAIN THE CHILLER
First, remove the Chiller Drain Cap. Then, unscrew and empty the Lower Water
Filter Housing. Then, unscrew the External Water Strainer. The unit can be tipped
slightly back to remove water inside the Chiller. Once drained, replace the Chiller
Drain Cap and Lower Water Filter Housing. Finally, replace the protective Chiller
Fitting Caps on the Inlet/Outlet connections.
TAKEDOWN COMPLETE
You are now ready to take your adventure on the road!
✓
IN
EDGE TUB USER MANUAL

PAGE - 13
EDGETHEORYLABS.COM
WATER MAINTENANCE
STEP 2) CHECK EXTERNAL WATER STRAINER
• Turn o Chiller, and close Tub Valves by turning handle perpendicular to the
valve body.
• Remove the bottom red “Inlet” Chiller Hose from the Chiller. Remove Water
Strainer Cover by twisting counterclockwise and check Inner Water Strainer for
debris; remove any foreign materials present. Use brillo pad or rough sponge
if necessary. Check the Strainer O-ring at the base of the threads is present and
free from damage before reinstalling Water Strainer Cover.
STEP 1) CHECK THE CHEMISTRY
• Start by adding 30cc (1 Measuring Cup) of Oxidizer for low volume (5 to 7
plunges per week) or 60cc (2 Measuring Cups) for high volume (7+ plunges per
week).
• Wait 15 minutes.
• Immerse Test Strip to a depth of 6” for 2 seconds. Remove and shake once to
remove excess water. Wait 10 seconds and compare to color chart on back of
bottle. If Sanitizer shows below the “OK” range, add 10cc (1/3 Measuring Cup).
Wait 15 minutes and test again. Repeat test and add more Sanitizer if necessary.
• If Alkalinity, pH, or Calcium are outside of desired range, balancers can be
purchased through our website. Of these, pH is most important to have in the
right range.
WEEKLY MAINTENANCE
SUMMARY:
There’s 3 simple steps for weekly maintenance that take about 15 minutes to
ensure that your Tu b is running properly and the water is clean and clear. The
first step is checking the water chemistry, then the External Water Strainer, then
the Water Filter.
STEP 3) CHECK WATER FILTER
• Check Water Filter condition by comparing to the diagram below. If the
condition is in the “Replace” range, or if the flow reading on the Control Panel
reads less than 13.0 L/min, then replace the filter with a new one. To access the
Water Filter, turn the Lower Water Filter Housing to the le if facing the back
of the Chiller. When changing the filter, empty water from Lower Water Filter
Housing fully and refill up to the top with fresh water.
• Ensure the Filter Housing O-ring in the Upper Water Filter Housing (white part) is
present and free from damage before reinstalling filter housing.
• Be sure to open the Tub Valves before turning the Chiller back on, or damage
will occur!
INITIAL SETUP:
•Add 60cc (2 Measuring Cups) of Oxidizer into water
•Wait 15 minutes
•Add 15cc (1/2 Measuring Cup) of Sanitizer into water
•Wait 15 minutes before entry into Tub
Replace Filter
EDGE TUB USER MANUAL

PAGE - 14
EDGETHEORYLABS.COM
RECOMMENDED ROUTINE MAINTENANCE
TUB
1. Disconnect the Tub from the Chiller.
2. Drain all water from the Tu b and Chiller Hoses.
3. Using mild soap and water, wash down the inside and outside of the Tu b using
a washcloth or so sponge. Place the Chiller Hoses inside the Tu b and run
soapy water through them.
4. Rinse Tub and Chiller Hoses o with clean water.
5. Allow Tub and Chiller Hoses to air dry completely; preferably in direct sunlight.
6. Any marks or scus on the Tub can be removed by lightly scrubbing with
a moistened Magic Eraser. Do not scrub aggressively or it may damage the
material. Do not use on any logos or printed areas!
7. Check air pressure of the Tub by connecting the Double Action Air Pump and
refilling to 10 PSI.
8. Check the area where the Tu b was located for any signs of mildew buildup and
clean if necessary. If large amounts of mildew buildup are noticed, the Tub may
need to be placed on a material that can breathe to allow water to evaporate.
9. Refill with water and perform initial Sanitizer protocol to sanitize the new
water.
CHILLER
Descaling
1. Disconnect the Chiller Hoses from the Tub. Ensure Tub Valve Fittings are in the
closed (perpendicular) position if the Tub still contains water.
2. Place both ends of the Chiller Hoses into a 5 gallon bucket or similar
container. Fill with distilled white vinegar (cleaning vinegar) and water at a
1:4 ratio.
3. Turn on the Chiller and run in heating mode at 104ºF. Allow the Chiller to
circulate water for 30 minutes.
4. Turn o the Chiller and empty the bucket of water. Refill with clean water.
Place Chiller Hoses back in the bucket and run the Chiller for another 30
minutes. The descaling process is now complete.
HOUSING MAINTENANCE
1. With a so cloth, wipe down the exterior of the Chiller with mild soap and
water.
2. Wipe o all soap residue with damp cloth.
3. With Chiller O, inspect fan and remove any debris that may be on or around
the fan shroud.
To ensure the longevity of your Edge Tub, it is recommended to perform
maintenance on your Chiller and Tub on a regular basis. This maintenance
protocol will help ensure that the Chiller functions as expected and that the
water quality of the Tub is kept clean. The steps below should be performed
every three months.
EDGE TUB USER MANUAL

O
U
T
L
E
T
Check OUTLET Port to ensure it is not
stuck in closed position
PAGE - 15
EDGETHEORYLABS.COM
TROUBLESHOOTING
WATER CIRCULATION TROUBLESHOOTING
Step 1)
The code o1.x or o2.x is shown on the display at startup and when Chiller is priming
with water. This screen is normal when establishing water circulation which can
take up to 2-3 minutes, especially if the Chiller and/or Chiller Hoses were recently
drained of water.
If aer 5 minutes the machine has still not established water circulation, please
check each of the following. The Chiller can be tested in between each step:
A.Ensure that the Tub Fitting Valves are in the open (parallel) position and hoses
are connected without leaks.
B.Check that the Water Filter and Inner Water Strainer are clean and clear of
debris. You can find instructions to replace and clean these parts on our
Maintenance Page. It is a good idea to proactively replace the Water Filter even
if it looks clean as minerals can block the filter but may not show discoloration.
C.Check the Hose O-Rings on each end of the Hose Connection Fittings. They
should be fully seated at the bottom of the threaded fitting and when attached,
the connection should only be tightened until a little resistance is felt and hose
no longer wiggles at connection point. Do not use tools to tighten.
D.Remove the Lower Water Filter Housing and ensure that the Filter Housing
O-Ring in the Upper Water Filter Housing (white part) is present and not
damaged. If you have a purple tinted Lower Water Filter Housing, check that
the lower O-ring is present as well. When reinstalling the Lower Water Filter
Housing, fill with water to the top and tighten only until a little resistance is
felt. Do not overtighten or it will deform the gasket and potentially damage the
O-Rings.
E.Ensure the Strainer O-Ring on the External Water Strainer is present and not
damaged. Replace if necessary from the spare parts kit. The Water Strainer
Cover should be hand tightened until it stops.
If the steps above do not resolve the issue, please move on to the next step.
WATER CIRCULATION TROUBLESHOOTING (CONTINUED)
Step 2)
Check Valve (Outlet Port)
There is a Check Valve inside the outlet port on the Chiller. This can become stuck
in the closed position and prevent water from flowing through the unit. If you
notice that the Chiller is trying to prime but no bubbles are coming out from the
Tub water-in fitting, this is a possible resolution. You will first close the Valves by
rotating to the Closed (perpendicular) position. Then Remove the Outlet Chiller
Hose and check to see if the little pin in the valve is stuck outward (toward you). If
it is stuck outward, use a small screwdriver and press on it gently. If it was indeed
stuck, you will feel / hear a little click that indicates the Check Valve has returned to
position. Reinstall the Chiller Hose, open the Tub valve, and try Chiller again.
Step 3)
Air Trapped in Unit
If you have recently taken a Chiller Hose o of the Chiller or Tub (For example, to
clean the Inner Water Strainer), it is possible that an air lock can be created within
the Chiller. We will want to release this air lock in the system by loosening the
Lower Water Filter Housing. Loosen the housing until it is completely o, fill up with
water to the top, and reinstall.
If the steps above do not resolve the problem, please contact:
[e-mail] so that we can further assist you!
EDGE TUB USER MANUAL

PAGE - 16
EDGETHEORYLABS.COM
OTHER TROUBLESHOOTING
• HOSE CONNECTIONS LEAKING:
Check to ensure gasket is in place; Disconnect and reconnect Chiller Hose, ensuring
snug hand tight connection; Replace Hose O-Ring with new one.
• TUB DEFLATES IMMEDIATELY AFTER INFLATING:
When inflating, ensure that the Inflation Valve Pin is in the depressed (out) position
prior to hooking up the Inflation Hose; if unsuccessful, Tub Inflation Valve may be
damaged and require replacement.
• TUB DEFLATES OVER TIME:
Temperature change may cause air pressure in Tub to change slightly, re-inflate
accordingly; If deflation continues regularly, use the air valve wrench, and tighten
the valve assembly. If deflation continues, an air leak may be present. Air leaks can
be found by using soapy water to locate the leak, and then the included repair kit
can be used to prevent further leaking.
• CHILLER WILL NOT TURN ON:
Ensure Chiller is plugged into an active power source and ensure the Power Switch
on the back of the Chiller is up in the “on” position. Press the orange “T” Test
Button above the Power Switch. The Power Switch should flip to the down “o”
position. Now flip the Power Switch back up to the “on” position. If this test does
not cause the Power Switch to turn o, do not proceed, and contact support for
assistance.
• WATER IS DRIPPING FROM CHILLER:
During heating mode, condensation may develop inside the Chiller in certain high
humidity conditions. A small amount of water drainage from the Chiller is normal
in this circumstance; Check Hose Connections are secure and that they are tight
and have O-Rings in place; Check Water Filter Housing connection and that it is
tight and has the Filter Housing O-Ring in place; Check Drain Plug Cap is in place
and tight.
• WHEN TEMPERATURE SET POINT IS INCREASED, CHILLER DOES NOT STOP
RUNNING:
If changing from a low set point to a higher one, or vice versa, the Chiller will
switch from Cooling mode to Heating mode to reach the new set point. The Chiller
will also cool or heat to a temperature just beyond the set point to ensure the
Chiller does not cycle on and o excessively, and will restart automatically when
the water temperature gets outside of the set range by a few degrees Fahrenheit.
• WATER HAS BECOME CLOUDY
Check filter element and replace if discolored; Add 60cc (2oz) of Oxidizer to water
to break down organics and allow to run for 2 hours; Replace water if this fails.
• TUB IS DIFFICULT TO GET INTO BAG
It is important that the Tub be fully deflated before folding. This is done by
deflating with the Double Action Hand Pump with Inflation Hose on the “Deflate”
side. Ensure Tub is folded correctly per Takedown instructions.
• CANNOT CONNECT CHILLER TO WIFI
Ensure that the WiFi network you are trying to access is 2.4ghz. This product
only works with a 2.4ghz wireless network. Some networks can be configured to
provide both frequencies if they are dual-band; Ensure WiFi password is correct by
testing with another device; Ensure Chiller is in-range of WiFi signal; Ensure device
with Tuya Smart app has internet connection.
• ERROR CODE: E1/FL/FU
Too much air inside the water circulating loop.
Double check the Chiller Hoses, Hose Connectors, External Water Strainer, and
Water Filter Housing to see if any connections are not properly made. Review
Water Circulation Troubleshooting above for more detailed steps to resolve.
• ERROR CODE: E2/HH
Water temperature is too high.
Wait for the water temperature to cool down and then select “Mode” (second
button) to cancel this error code.
• ERROR CODE: E3/FU
Water flow is low.
See Water Circulation Troubleshooting instructions above for detailed steps
to resolve.
• ERROR CODE: E4/AA
Temperature sensor T4 failure
Contact Edge Theory Labs Support.
• ERROR CODE: E5/PA
Temperature sensor T3 failure
Contact Edge Theory Labs Support.
• ERROR CODE:CH2
Temperature sensor T2 failure
Contact Edge Theory Labs Support.
EDGE TUB USER MANUAL

PAGE - 17
EDGETHEORYLABS.COM
LIMITED WARRANTY
Edge Theory Labs warrants this product to be free from defects
in workmanship and materials, under normal residential use
and conditions, for a period of one (1) year from the original ship
date, or six (6) months for commercial use. Edge Theory Labs
agrees, at its unfettered discretion, during the warranty period,
to repair any defect in material or workmanship or to furnish
a repaired or refurbished product of equal value in exchange
without charge (cost of shipping and handling will be covered
by Edge Theory Labs so long as the warranty claim is deemed
legitimate, as outlined in this paragraph above). Such repair or
replacement is subject to verification of the defect or malfunction
and proof of purchase and Edge Theory Labs retains the right
to dismiss a warranty claim if foul play is suspected. For clarity,
this warranty does not include: Any condition resulting from
other than ordinary residential wear or any use for which the
product was not intended, such as use in rental or contract trade
or commercial use, any condition resulting from incorrect or
inadequate maintenance or care, any condition resulting from
modifications, damage resulting from misuse, abuse, negligence,
accidents, dissatisfaction due to buyer’s remorse, normal wear
and tear, damages incurred during transportation, or failure to
comply with all instructions and warnings.
The Edge Tub Elite User Manual
EDGE TUB USER MANUAL

PAGE - 18
EDGETHEORYLABS.COM
RECOMMENDED ACCESSORIES
PROTECTION MAT - Edge Theory Labs
SUMP PUMP - Amazon
GARDEN HOSE ADAPTER - Amazon
ELECTRIC AIR PUMP - Edge Theory Labs
AQUA VACUUM - Amazon
BREATHABLE TILES - Amazon
EDGE TUB USER MANUAL