Edimax EdiView User manual

To Install EdiView IP camera utility on Android device, follow the following
instructions:
To install Ediview application, launch ‘Market’. (In your
Android device’s ‘All apps’menu).
Click magnifier icon at upper-right corner of Android
market, and input ‘Ediview’in search field.

You should able able to find Ediview utility (If not,
please check spelling), and click ‘Download’to
download and install Ediview.
Android will prompt you to confirm installation, please
click ‘Install’button below to start installation.

Please be patient while EdiView is being installed.
When EdiView utility is successfully installed, you’ll
see this message. Click ‘Open’to launch EdiView
utility now, or click ‘Complete’to launch EdiView
utility later.

You can launch EdiView by clicking ‘EdiView’icon in
‘All Applications.
When you launch EdiView, it will search for all Edimax
IP cameras on your network.
Please make sure you’re connected to wireless access
point if your Edimax IP camera is located on your local
area network.
If you want to add a Ediamx IP camera on Internet,
please click ‘Manually’button to abort and setup IP
camera manually.

In this page, you can input IP camera’s parameters
manually:
Name: You can define a name for this IP camera to
help you to remember the purpose / location of this IP
camera.
Cloud / IP Mode Switch: Click this button to switch
operating mode between Cloud and IP. In cloud mode
you have to input Cloud ID**; In IP mode you have to
input IP address or host name of IP camera.
User Name: Input the user name of IP camera. Default
user name is ‘admin’
Password: Input the password of IP camera. Default
user name is ‘1234’
Click ‘Add’to add a new IP camera with parameters
listed above.
When an IP camera has been added successfully,
you’ll see it appear in EdiView utility’s camera list.
Please repeat last step to add more IP cameras you
wish to connect. To repeat last step, press ‘Menu’key
on your Android device and click ‘Add’button.

If the IP camera is connected, you’ll see a picture
appear. Click the picture to view live image.
If there are new events available, click icon;
To configure IP camera’s parameters, click icon.
When you click an IP camera in camera list, you’ll see
its live image like this.
You can hold your Android device horizontally to
enlarge IP camera’s live image view.
If the IP camera you connected supports Pan/Tilt, you
can click button and use your finger to slide on
the live image to the direction you wish to move.

To take a snapshot of current live image and save it on
your Android device, click button.
You’ll see ‘Save Snapshot’message appear, which
indicates a snapshot has been taken.
If you have more than 1 IP cameras, you can click
button and you can see the image of up to 4 IP
cameras at the same time; Click on the camera’s
image to enlarge it.
You can also click button to see up to 12 IP
cameras at the same time.

To configure the video display parameters of this IP
camera, click button, and you can drag the slide
bar to configure parameters:
Brightness: Configure video brightness
Saturation: Configure video saturation.
Sharpness: Configure video sharpness.
Video Quality: Configure video quality by setting a
lower (left) or higher (right) image quality. When
network speed is slow, using a lower video quality will
help.
Pan / Tilt speed: configure the camera moving speed
when you use pan / tilt function.
Click ‘Done’button when you finish, or click ‘Cancel’
to abort. You’ll see the result after you click Done’.
Event:

When a new event (movement) has been detected by
IP camera, you’ll see icon appear in IP camera list.
You can click it to see events.
All events will be displayed here, with the time which
triggered this event.
Click on the event to see enlarged picture.

The image of this event will be displayed with the time
triggered this event. To see enlarged picture, hold
your Android device horizontally.
To save a snapshot of this event, click button.
You’ll see ‘Saved event image successfully’message to
prompt you that image has been saved successfully.

Other functions - Event
When you’re in camera list, press ‘Menu’button on
your Android device. A menu will appear on the
bottom of EdiView utility.
See live images of IP cameras
Use google map to locate IP cameras
Add a new IP camera
Reload IP camera list

Other Functions - Map
You can use this function to mark your IP camera on
Google map, so you can locate them and remember
their physical location easily.
Please note that you need active Internet connection
to show map on your Android device.
Click ‘Map’button at the bottom of your Android
device to access Map menu.
Google map will be shown on your Android device,
and it will attempt to locate your current location by
GPS and network.
If you’re using your Android device indoor, your A may
fail to locate your location. You can still use your finger
to drag the map and find your current location
manually.
If the IP camera you’re about to mark on the map
does not locate at your current location, you can also
use your finger to drag the map and find the location
where your IP camera is installed.
A blue pin indicating the location of IP camera will be
placed at the center of map.

When you found the location where IP camera is
installed, press ‘Menu’button on your Android device
and click ‘Locate’button and a camera list will be
shown.
Select the IP camera you wish to mark on the map.