edishine HHSL04A1 User manual

[Instruction Manual]
SKU:HHSL04A1
LED Knuckle Motion Sensor Flood Light
Thank you for your purchase.
Please contact us if you have any questions.
We will get back to you within 24 hours.
Please attach your Order ID so that
we can serve you better.
V211026

1. Before installation, please cut off the power.
2. Remove old fixture if necessary for installation.
3. Connect line voltage (hot) AC supply wire(s) (Black) to the line voltage
AC wire(s) (Black) inside the canopy via the wire connector.
4. Connect neutral (common) AC supply wire(s) (White) to the neutral AC
wire(s) (White) inside the canopy via the wire connector.
5. Connect the grounded AC supply wire(s) [Green or bare wire(s)] to the
grounded AC wire(s) [bare copper wire(s)] using the wire connector.
6. Cap and insulate all unused leads.
7. To aim the light, loosen the side bolt connected to the knuckle arm to aim
the fixture up or down. Re-tighten bolt to secure the fixture in the desired
position.
WARNING: PROPOSITION 65
WARNING
Handling the coated electrical wires of this product can expose you to
chemicals including lead, which is known to the State of California to cause
cancer and/or birth defects or other reproductive harm. For more information
go to www. P65Warnings.ca.gov.
Read all of these installation instructions before installing the fixture. These
products may represent a possible shock or fire hazard if improperly installed
or attached in any way. Products should be installed by a qualified electrician
in accordance with these instructions, current local electrical code or the
current National Electric Code (NEC).
1. This product must be installed by a person familiar with the construction
and operation of the product and the hazards involved, and in accordance
with current electrical codes and/or the current National Electric Code (NEC).
2. To reduce the possibility of electric shock, fixture must be grounded.
3. Do not attempt to open the LED light engine.
4. Do not look directly into fixture.
5. Fixture is equipped with 120 VOLT Driver ONLY.
INSTRUCTIONS
01

OPERATING INSTRUCTIONS
8. To prevent rain, use silicone caulk to caulk the top and sides of the
canopy and aiming arm.
The motion sensor on this fixture has a built in Dusk-to-Dawn sensor that
automatically disables the motion sensor during daylight hours regardless
of motion detection.
1.The motion sensor must be tested
before setting the Time and sensitivity
levels. The TEST option is located on
the TIMER control knob on the
underside of the sensor head. To test
the fixture, switch the wall switch that
controls power to the fixture to the ON
position and turn the rotary knob to the
“TEST” area. During test mode, the
lights will come on for 20 seconds,
regardless of motion detection or the
time of day. The light will shut off automatically after 20 seconds. Leave the
rotary knob in the “TEST” area and test the sensitivity by crossing in the path
of the sensor. The light will come on only if it senses movement. Once
movement stops, it will turn off in 5 seconds. The test is now complete.
02
Outlet box (not provided)
Ground wire
Wire connector Black live wire
White neutral wire
Outlet box screw
1

03
2.Once the fixture has been tested for
proper operation and sensitivity, rotate
the TIMER control knob past the “1”
setting into the timer settings. The timer
settings indicate how long the light
stays on after the PIR senses motion.
Rotating this knob clockwise raises the
stay on time of the motion sensor for
up to 10minutes .Rotating the knob
counterclockwise shortens the stay on time to as close as 1 minutes (can’t
past “1” position). It may be necessary to adjust the TIMER knob several
times until the desired ON time is achieved.
3.Rotate the TIMER control knob to
the “D2D” position,the light turns on at
dusk and off at dawn automatically,
regardless of the presence of motion.
The “D2D” setting ensures lights are
non-operational in daylight and only
function at night.
4.The control knob located on the
opposite side is Marked SENSITIVITY,
which determines the degree of Motion
detection. Rotating this knob clockwise
raises the sensitivity of the motion sensor
for up to 60 ft of distance. Rotating the
knob counterclockwise lowers the sensitivity
down to as close as 10 ft. It may be
necessary to adjust the “SENSITIVITY”
knobseveral times until the desired setting
is achieved.
2
3
4

04
5.The 180 degree coverage of the
motion sensor is measured side to
side. Therefore, the sensor will better
detect motion across the field of view
(side-to-side), rather than motion coming
straight at the sensor (in-and-out).
Adjust the motion sensor head so that
it detects motion moving across the
cover area. The position of the sensor
head should not exceed 45 degrees
from horizontal. Do not aim the Motion
sensor at a body of water, bushes or plants that may move in the wind,
pedestrian traffic, moving cars, Etc., as this will trigger the motion sensor.
6. When the TIMER control knob be
set at the Timer area (between “1”
and “10”, the sensor is in Auto mode
at this time), to control the light from
inside the home, activate manual
override mode by toggling the wall
light switch OFF and ON within 2
seconds. The security light will turn
on and stay on for approximately 8 hours, or until the Dusk-to-Dawn sensor
detects light in the morning. Once the Dusk-to-Dawn sensor detects light,
the manual override mode will automatically go back to its original settings
of the AUTO motion sensor.
NOTE: The higher sensitivity level increases the Likelihood of a false
activation being triggered.
NOTE: If the Sensor arm becomes loose, it will not hold the sensor head at
the joint screw on the sensor arm.
180° 45°
18,29 m/60pi
6
Manual Override Operating Diagram
Turn Wall switch
OFF - ON within 2 sec
Auto Mode
Turn wall switch
OFF - ON within 2sec
or
rest automatically after 8 hours
Manual
Override
Mode

Motion Sensor Features：
Turn-On Light Levels: 10-90 Lux
Turn-Off Light Levels: Max 800 Lux
Time Delay: 10-300 Seconds (To avoid the influence of other light
sources, a delay of 10s-300s is set when the fixture is
turned off).
Sensitivity: 10FT, 20 FT, 50 FT, 60 FT（MAX）
Timer: 1Minutes, 5 Minutes, 10 Minutes
Motion Sensor
LIGHT OPERATION
05
MODE
Test mode. Test position. On. Any setting.
Any setting.
Any setting.
Any setting.
Any setting.
On.
On.
On.
Timer area
(between “1” and “10”).
D2D position.
Timer area
(between “1” and “10”).
Toggle OFF and ON
within two seconds.
Timer area
(between “1” and “ 10”).
AUTO motion
sensor mode.
Dusk to Dawn mode.
Manual override mode.
Return to AUTO
Motion sensor mode.
CONTROL KNOB WALL SWITCH SENSITIVITY KNOB

06
TROUBLESHOOTING
PROBLEM
Light does not come
on at night when
Motions detected.
1. No power is being
delivered to the fixture.
2. Another light source is causing
the security light to think it is
daylight.
3. Wiring inside electrical box
came loose.
1. Check that circuit breaker and/or
wall switch power is on.
2. Turn off surrounding lights
and/or re-aim the sensor head.
3. AFTER turning power off to the
fixture, reconnect any loose wiring.
POSSIBLE CAUSE CORRECTIVE ACTION
NOTE: Manual override mode means that the TIMER button is between one
and ten minutes. At night, when the lamp is on, turn off the power and turn it
on again within two seconds. The lamp will automatically light up for eight
hours during which the Motion Senor will not work. If it does not arrive for
eight hours, when the outdoor light reaches the brightness that triggers the
shutdown of the lamp, the lamp will be turned off, after the lamp is turned off,
it will automatically return to the Auto motion sensor mode;
Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner
and soft cloth. When cleaning the fixture, make sure the power is turned off.
Do not spray cleaner directly onto any part of the fixture or LEDs.
CARE AND MAINTENANCE
Extreme hot or cold weather could affect the performance of the built-in sensors
that detect body heat. Certain winter clothing can shield a person’s body heat
from the sensor during extreme cold weather.During extreme hot weather, the
sensor may not be able to distinguish the difference between normal body
temperatures and the surrounding high temperatures. The sensor will begin
working normally once weather conditions return to normal.
TROUBLESHOOTING

07
Reminder
PROBLEM
Security light comes on
during the day.
Security light cycles ON
and OFF continuously.
Security light comes on for
no apparent reason at night.
1. Dusk-to-Dawn sensor is
a shaded area and is fooled into
thinking it is nighttime.
2. Dusk-to-Dawn sensor
is faulty.
1. Dusk-to-Dawn sensor is sensing
reflected light from the security light.
1. Light is sensing motion in the
detection zone.
1. Shine a flashlight onto the light
sensor. If the security light turns off
then the fixture is mounted in an area
that does not allow enough light to
enter the sensor. Relocate security
light.
2. If under warranty, contact Customer
Service.
1. Change the position of the light
head, aim light away from the
reflecting surfaces.
2. Put a small piece of black electrical
tape over the Dusk-to-dawn sensor.
3. Relocate the security light to a
different location where it no longer
causes reflected light.
1. Make sure the sensor is not picking
up moving objects such as bushes,
trees, traffic, water, etc.
2. Test the motion sensor by covering
up the front curved lens with
cardboard to block the view. If the
light turns off then something in the
detection zone is triggering the sensor.
Reposition the motion sensor or change
the sensitivity (distance) of the sensor.
POSSIBLE CAUSE CORRECTIVE ACTION

- LED Knuckle Motion Sensor Flood Light x 1
- Instruction Manual x 1
- Sponge Gasket x 1
- Wire Connector x 3
- Screw x 4
08
One Year Limited Warranty
EDISHINE warrants this product to be free from defects in material and
workmanship for a period of one year from the date of purchase.
Warranty is void if damage is caused by misuse or improper installation.
Our dedicated customer service team will get back to you within 24 hours.
Package Includes
- Input voltage: 120V 60Hz
- Wattage: 65W
- Luminance: 6670lm
- Color temperature: 5000K
- CRI: 80+
- Life span: 60000 hours
Specifications