Edsal UR-185PBB User manual

Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible
safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not included. Do not
use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE UNIT, OR
USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom. Use care
when working with metal parts. Do not use this unit to store aquariums.
Models:
UR-185PBB
UR-4818PBB
UR-245PBB
D - Wood Shelf
C - Post
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the
beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood
between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.
B - Brace
Steel Storage Rack
E - Post Coupler
Model UR-185PBB
36"w x 18"d x 72"h
Description Qty Part Number
(A) beam 10 URBM36-BLK
(B) brace 10 URBR18-BLK
(C) post 8URPS36-BLK
(D) wood shelf 5RPB31836
(E) post coupler 4CPOUT-BLK
(F) post cap 8RL-PC-B1.4
Should you have any comments, damage, missing parts, or problems with assembly of this unit contact us:
Chat: www.edsal.com/chat or www.edsal.com/contact
Email: [e-mail]
Phone: [phone]
To obtain replacement parts please provide: Model Number, Part Number & Description,
Location Purchased, and Date Purchased
Edsal Manufacturing Co. LLC
Chicago, IL 60609
US Patents & Patents Pending
Rev: 032620_hd
F - Post Cap
A - Beam
Model UR-245PBB
48"w x 24"d x 72"h
Description Qty Part Number
(A) beam 10 URBM48-BLK
(B) brace 10 URBR24-BLK
(C) post 8URPS36-BLK
(D) wood shelf 5RPB32448
(E) post coupler 4CPOUT-BLK
(F) post cap 8RL-PC-B1.4
Model UR-4818PBB
48"w x 18"d x 72"h
Description Qty Part Number
(A) beam 10 URBM48-BLK
(B) brace 10 URBR18-BLK
(C) post 8URPS36-BLK
(D) wood shelf 5RPB31848
(E) post coupler 4CPOUT-BLK
(F) post cap 8RL-PC-B1.4

Figure F
Assemble two (2) post with one (1) brace. Skipping one slot
from the bottom of the post (see figure A), place the rivets
into post with the narrow end of the slots pointing down, and
with the shelf ledge of the brace facing up (see figure B). Tap
lightly on the top edge of the brace to seat rivets. Repeat with
two (2) post and one (1) brace. Next assemble the two (2)
post units with two (2) beams, skipping one slot from the bot-
tom of the post (see figure C). Place the rivets into post with
the narrow end of the slots pointing down, and with the shelf
ledge of the brace facing up (see figure B). Tap lightly on the
top edge of the beam to seat rivets.
Assembly Instructions UR-185PBB, UR-4818PBB & UR-245PBB
Step
1
Figure C
Brace
Post
Beams
Figure C
IMPORTANT NOTE : Make sure all rivets are fully seated into the post
Start by adding a wood shelf to the level previously built,
then continue working by adding the second level using
two (2) beams and two (2) braces to the post slots of
your desired location. Again, place the rivets of the
beams and braces into the post slots with the shelf
ledge facing up and tap lightly to seat the rivets.
Step
2
Wood Shelf
Figure A
Tap lightly
to seat
rivets
Posts are
directional.
The narrow
end of the
slots must
point down.
Brace/Beam
ledge
Rivets
Figure B
Add a wood shelf to the previously built level, then assem-
ble four (4) posts to the four bottom post assemblies by us-
ing four (4) of the post couplers. Place the post coupler into
the top of the bottom post assembly and tap down to
properly seat. Next place a post into the top of the post cou-
pler and tap down to properly seat (see figure D). Continue
by adding the third level using two (2) beams and two (2)
braces just above the post couplers. Again tap lightly to seat
the rivets.
Step
3
Wood Shelf
Note: Posts are directional.
The narrow end of the slots
must point down.
Figure D
Bottom
Post
Top
Post
Post
Coupler
Add a wood shelf to the previously built level, then
continue by adding the fourth and fifth level to the unit
using two (2) beams and two (2) braces per level. Tap
lightly to properly seat the rivets and add the final wood
shelves to the unit (see figure E). Finally place the four
(4) post caps on the top of each post (see figure F).
Step
4
Figure E

FiguraF
Ensamble dos (2) postes con una (1) abrazadera. Omitiendo una
ranura de la parte inferior del poste (ver figura A), coloque los
remaches en el poste con el extremo angosto de las ranuras
apuntando hacia abajo, y con la saliente del estante hacia arriba
(ver figura B). Golpee ligeramente en el borde superior de la
abrazadera para asentar los remaches. Repita con dos (2)
postes y una (1) abrazadera. Despues ensamble las dos (2)
unidades de postes con dos (2) vigas, omitiendo una ranura de
la parte inferior del poste (ver figura C). Coloque los remaches
en el poste con el extremo angosto de las ranuras apuntando
hacia abajo, y con la saliente del estante hacia arriba (ver figura
B). Golpee ligeramente en el borde superior de la viga para
asentar los remaches.
Instrucciones de Ensamblaje UR-185PBB, UR-4818PBB & UR-245PBB
1
Figure C
Abrazadera
Poste
Vigas
FiguraC
NOTA IMPORTANTE: Asegúrese que todos los remaches estén completamente asentados en el poste
Comience agregando una repisa de madera al nivel
previamente construido, luego continúe trabajando agregando
el segundo nivel usando dos (2) vigas y dos (2) abrazaderas
en las ranuras de los postes de su ubicación deseada.
Nuevamente, coloque los remaches de las vigas y las
abrazaderas en las ranuras de los postes con la saliente del
estante mirando hacia arriba y golpee ligeramente para
asentar los remaches.
Paso Paso
2
Repisa de Madera
FiguraA
Golpee
ligeramente
para asentar
remaches
Los postes son
direccionales.
El extremo
angosto de las
ranuras debe
apuntar hacia
abajo
Saliente de la
Abrazadera/Viga
Remaches
FiguraB
Agregue una repisa de madera al nivel previamente construido,
luego ensamble cuatro (4) postes a los cuatro ensambles del
poste inferior usando cuatro (4) de los acoples de poste. Coloque
el acople de poste en la parte superior del ensamble del poste
inferior y golpee hacia abajo para asentar correctamente. Despues
coloque una poste en la parte superior del acople de poste y
golpee hacia abajo para asentar correctamente (ver figura D).
Continúe agregando el tercer nivel utilizando dos (2) vigas y dos
(2) abrazaderas justo encima de los acoples de los postes.
Nuevamente golpee ligeramente para asentar los remaches.
Paso
3
Repisa de madera
Nota: Los postes son
direccionales. El extremo
angosto de las ranuras
debe apuntar hacia abajo.
FiguraD
Poste
Inferior
Poste
Superior
Acople
del
Post
Agregue una repisa de madera al nivel previamente
construido, luego continúe agregando el cuarto y quinto nivel
a la unidad usando dos (2) vigas y dos (2) abrazaderas por
nivel. Golpee ligeramente para asentar correctamente los
remaches y agregue las repisas de madera finales a la
unidad (ver figura E). Finalmente coloque las cuatro (4)
tapas de poste en la parte superior de cada poste (ver figura
F)
Paso
4
FiguraE