Edsal UR-364 User manual

These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible
safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not included. Do not
use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE UNIT, OR
USE IT AS A LADDER. Do not store aquariums on this unit. Evenly distribute the weight on each level and always keep the
heavier loads on the bottom. Use care when working with metal parts, wear gloves for protection.
MODEL NUMBERS
UR-364
UR364-BLK
UR364P-BLK
D - Wood Shelf C - Post
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the
beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood be-
tween the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.
A - Beam
B - Brace
Steel Storage Rack
E - Inside Coupler
UR-364
4 Shelf 60”h x 18”d x 36”w
Description Qty Part Number
A beam 8UBE3502GY
B brace 8UBE1702GY
C post 8UPT3002GY
D shelf 4RPB21836
E coupler 4MPCIN-GY
UR364-BLK; UR364P-BLK
4 Shelf 60”h x 18”d x 36”w
Description Qty Part Number
A beam 8UBE3502BK
B brace 8UBE1702BK
C post 8UPT3002BK
D shelf 4RPB21836
E coupler 4MPCIN-BK
Should you have any comments, damage, missing parts, or problems with assembly of this unit contact us:
Chat: www.edsal.com/chat or www.edsal.com/contact
Email: [e-mail]
Phone: [phone]
To obtain replacement parts please provide: Model Number, Part Number & Description, Location Purchased, and Date Purchased
Edsal Manufacturing Co. LLC
1555 W. 44th Street
Chicago, IL 60609
www.edsal.com
US Patents & Patents Pending

Assemble two (2) post with one (1) brace. Skipping one slot
from the bottom of the post (see figure A), place the rivets
into post with the slot pointing down, and with the shelf ledge
of the brace facing up (see figure B). Tap lightly to seat riv-
ets. Repeat with two (2) post and one (1) brace. Assemble
the two (2) post units with two (2) beams (see figure C). Skip
one hole from the bottom of post, tap lightly to seat rivets.
Start by adding a wood shelf to the level previously built,
then continue working by adding the second level using
two (2) beams and two (2) braces in the post slots of
your desired location. Again place the rivets of the
beams and braces into the post slots with the shelf
ledge facing up and tap lightly to seat the rivets.
Add a wood shelf to the previously built level, then con-
tinue by adding the fourth level to the unit using two (2)
beams and two (2) braces per level. Tap lightly to
properly seat the rivets and add the final wood shelves to
the unit (see figure E).
Step
1
Step
Step Step
Figure A
Figure B
Figure C
Shelf Ledge
Brace
Post
Wood Shelf
Tap Lightly
Beam
Figure C
Note:
Post are
directional.
The slot
must point
down. Post Slot Points Down
Note:
Post are directional. The slot must point down.
Add a wood shelf to the previously built level, then assem-
ble the top post to the bottom post by using four (4) of the
post couplers. Place the couplers into the top of the bot-
tom post, and the bottom of the top post and tap down to
properly seat (see figure D). Continue by adding the third
level using two (2) beams and two (2) braces just above
the post couplers. Again tap lightly to seat the rivets.
Figure D
Top
Post
Post
Coupler
Bottom
Post
43
2
Figure E