Edsal WorkForce UR361860 User manual

Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the
heavier loads on the bottom. Use care when working with metal parts.
Steel Storage Rack MODEL NUMBER
UR361860
F - Woodboard Shelf
E - Post
G - Post Coupler
UR361860 4 Shelf
UR361860 4 Shelf
UR361860 4 Shelf -
-
-60”h x 18”d x 36”w
60”h x 18”d x 36”w
60”h x 18”d x 36”w
Description
A - Dbl. Beams
B - Dbl. Braces
C - Sgl. Beams
D - Sgl. Braces
E - Post
F - Woodboard
G - Coupler
H - Post Cap
Qty.
4
4
4
4
8
4
4
4
Part Number
RUBE 3502
RUBE 1702
RBBE 3501
RBBE 1701
RUPT 3002S
RPB 21836
RMPC 0409
RL-PC
Part Size
35 7/16”
17 7/16”
35 7/16”
17 7/16”
30”
36” x 18”
4”
N/A
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used
on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block
of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and
fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our Work Force manufacturing facility at, [phone] and request customer service.
We can also be reached on the internet at the following email address : [email protected].
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
Consumer Products Division
Edsal Manufacturing Company
4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com
A - Double
Beams
B - Double
Braces
D - Single
Braces C - Single
Beams
H - Post Cap

Assemble two (2) post with one (1) double brace (see fig-
ure A). Skipping one slot from the bottom of the post,
place the rivets into post with the shelf ledge facing up (see
figure B). Tap lightly to seat rivets. Repeat with two (2)
post and one (1) double brace. Assemble the two (2) post
end units with two (2) double beams (see figure C). Skip
one slot from the bottom of post, tap lightly to seat rivets.
Assembly Instructions for UR361860
Assembly Instructions for UR361860
Assembly Instructions for UR361860
Start by adding a woodboard shelf to the level previously
built, then continue working by adding the second level
using two (2) single beams and two (2) single braces in
the post slots of your desired location. Again place the
rivets of the beams and braces into the post slot with the
shelf ledge facing up and tap lightly to seat the rivets.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
Step
1
Step
2
Step
3
Step
4
Figure A
Brace
Post
Woodboard Shelf
Beam
Figure C
Top Post
Figure D
Post Coupler
Add a woodboard shelf to the previously built level, then
assemble the top post to the bottom post by using four (4)
of the post couplers. Place the couplers into the top of the
bottom post, and the bottom of the top post and tap down
to properly seat (see figure D). Continue by adding the
third level of single beams and single braces just above
the post couplers. Again tap lightly to seat the rivets.
Add a woodboard shelf to the previously built level, then continue
by adding the final level to the unit using two (2) double beams
and (2) double braces. Tap lightly to properly seat the rivets and
add the final woodboard shelf to the top of the unit. Install all four
(4) end caps to the top of the unit after assembly has been com-
pleted (see figure E). Install end caps to post by pressing down
on end cap at the three points illustrated above (see figure F).
Bottom Post Woodboard Shelf
Figure B
Shelf Ledge
Tap Lightly
Note:
Post are
directional.
The slot
must point
down. Post Slot Points Down
Note:
Post are
directional.
The slot
must point
down.
Top Of Unit
Figure E
Press Down
Figure F