EKO Commercial Sinks User manual

INSTALLATION GUIDE
Commercial Sinks
(2016)

EKO Living Elements, LLC | April, 2016 PAGE 2
READ CAREFULLY!
BRACKETS MUST BE INSTALLED BEFORE SHEETROCK
INSTALLATION.
ALL SINKS REQUIRE TWO PRIMARY (LARGER) BRACKETS.
ALL SINKS GREATER THAN 40” LONG REQUIRE TWO OR MORE
SECONDARY (SMALLER) BRACKETS.
DISTANCE BETWEEN ANY TWO BRACKETS MUST NOT BE MORE
THAN 36” APART ON CENTER.* ADDITIONAL SECONDARY
BRACKETS MAY NEED TO BE PROVIDED TO MEET THIS
REQUIREMENT DEPENDING ON SINK LENGTH.
DISTANCE BETWEEN THE TWO PRIMARY BRACKETS IS DEPENDENT
ON SINK LENGTH. REVIEW AVAILABLE MATERIALS.
*Rule does not apply to trough sinks, see trough sink installation pages for details (Page 7-8)

EKO Living Elements, LLC | April, 2016 PAGE 3
COMMERCIAL “INCLINE” SINK INSTALLATION
Bracket Placement:
-Brackets are to be mounted with thru-bolts through a sturdy upright support such as
a 2x4 stud or other similarly strong member.
-The distance between any two brackets cannot be more than 36”. Secondary
brackets should be centered between the primary brackets (refer to pictures on
page 4). Additional secondary brackets may be needed depending on sink length.
-The sink must have a finished height of 34”from the ground to meet ADA
compliancy. It is recommended to install the brackets at shown heights and shim the
sinks to a finished height of 34”.

EKO Living Elements, LLC | April, 2016 PAGE 4
Auxiliary Support:
-An auxiliary support
will be needed that will span the
distance between the two primary
brackets. Typically, an appropriately
sized wooden stud is sufficient.
-The support will be
flush with the top of the primary
brackets as shown in the picture.
-Fasten the support by
any means necessary.
Sink Mounting:
-USE CAUTION. The
sinks can be easily damaged or
chipped. Be careful to avoid possible
collisions or scratches at all times.
-Mount the sink onto
the brackets and support using
construction adhesive to secure the
sink in place as shown in the picture.

EKO Living Elements, LLC | April, 2016 PAGE 5
COMMERCIAL “RETTANGOLO” SINK INSTALLATION
Bracket Placement:
-Brackets are to be mounted with thru-bolts through a sturdy upright support such as
a 2x4 stud or other similarly strong member.
-The distance between any two brackets cannot be more than 36”. Secondary
brackets should be centered between the primary brackets (refer to picture on page
6). Additional secondary brackets may be needed depending on sink length.
-The sink must have a finished height of 34”from the ground to meet ADA
compliancy. It is recommended to install the brackets at shown heights and shim the
sinks to a finished height of 34”.

EKO Living Elements, LLC | April, 2016 PAGE 6
Auxiliary Support:
-An auxiliary support
will be needed that will span the
distance between the two primary
brackets. Typically, an appropriately
sized wooden stud is sufficient.
-The support will be
flush with the top of the primary
brackets as shown in the picture.
-Fasten the support by
any means necessary.
Sink Mounting:
-USE CAUTION. The
sinks can be easily damaged or
chipped. Be careful to avoid possible
collisions or scratches at all times.
-Mount the sink onto
the brackets and support using
construction adhesive to secure the
sink in place as shown in the picture.

EKO Living Elements, LLC | April, 2016 PAGE 7
COMMERCIAL “TROUGH” SINK INSTALLATION
Bracket Placement:
-Brackets are to be mounted with thru-bolts through a sturdy upright support such as
a 2x4 stud or other similarly strong member.
-The distance between the two secondary brackets must be at 10”apart on center
and centered between the two primary brackets (refer to picture on page 8).
Additional secondary brackets may be needed if the trough sink has multiple basins.
-The sink must have a finished height of 34”from the ground to meet ADA
compliancy. It is recommended to install the brackets at shown heights and shim the
sinks to a finished height of 34”.

EKO Living Elements, LLC | April, 2016 PAGE 8
Auxiliary Support:
-An auxiliary support
will be needed that will span the
distance between the two primary
brackets. Typically, an appropriately
sized wooden stud is sufficient.
-The support will be
flush with the top of the primary
brackets as shown in the picture.
-Fasten the support by
any means necessary.
Sink Mounting:
-USE CAUTION. The
sinks can be easily damaged or
chipped. Be careful to avoid possible
collisions or scratches at all times.
-Mount the sink onto
the brackets and support using
construction adhesive to secure the
sink in place as shown in the picture.