Elation PRO BAR 4 User manual
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
AutoProgram
Hold Sound
Prog Sound
AutoSound
StandBy
AudioSen.
MaxMin
1 2 3 4F
FUSES
F10A250V
(5x20mm)
12
34
CONSTANT
POWER
MIDI IN
MIDI THRU
NL
E
1/4"stereojack
FullOn
StandBy
GND
REMOTE POWER INPUT
CHANNEL
1
CHANNEL
2
CHANNEL
3
CAUTION ! RISK OF ELECTRIC SHOCK
DISCONNECT INPUT POWER
BEFORE OPENING
N'OUVREZ PAS..RISQUEDE CHOC ELECTRIQUE
WARNING: THIS APPARATUSMUST BE EARTHED
POWER INPUT: AC 120V~ 50-60Hz
OUTPUT: 10A /CHANNEL, Total20A.
PRO BAR 4
DMX IN
DMX OUT
1 = Ground
2 = Data-
3 = Data+
CHANNEL
4
4295 Charter Street
Los Angeles CA. 90058
www.elationlighting.com
User Instructions
Elation Professional R
All manuals and user guides at all-guides.com
all-guides.com
Contents
Features 1
Technical Specifications 12
General Instructions 2
1. Overview 3
2. Operation Guide 5
2.1 Mode Select 5
2.2 DMX Mode 5
2.3 MIDI Mode 6
2.4 Master Mode 7
2.5 Preset Functions 8
2.6 Chase Direction 10
2.7 Cross and Normal Dimmer 10
2.8 Link Up 11
2.9 Initialization 11
Improvement and changes to
specifications, design and this
manual, may be made at any time
without prior notice.
All rights reserved.
All manuals and user guides at all-guides.com
Contents
Features 1
Technical Specifications 12
General Instructions 2
1. Overview 3
2. Operation Guide 5
2.1 Mode Select 5
2.2 DMX Mode 5
2.3 MIDI Mode 6
2.4 Master Mode 7
2.5 Preset Functions 8
2.6 Chase Direction 10
2.7 Cross and Normal Dimmer 10
2.8 Link Up 11
2.9 Initialization 11
Improvement and changes to
specifications, design and this
manual, may be made at any time
without prior notice.
All rights reserved.
All manuals and user guides at all-guides.com
DO NOTdismantle or modify the unit.
Packaging material (plastic bags, polystyrenefoam, nails, etc.) MUST NOT be left
within children's reach, as itcan be dangerous.
After having removed thepackaging check that theunit is NOT damaged in any way.
If in doubt,DON'T use it and contactan authorized dealer.
This unit is intendedfor indoor use only.
NEVER try to repair the unit yourself. Repairs by unqualified people could cause
damage or faulty operation. Contact your nearest dealer.
Wait for at least one second to turn on the power after turning off this unit.
DO NOT open the unit--there are no user serviceable parts inside.
Take care not to damage the power cord.
STOP using the unit immediately In the event of serious operation problems and
either contact your localdealer for a checkor contact us directly.
DO NOT make any inflammable liquids, water or metal objects enter the unit.
To prevent fire or shock hazard, do not expose this product under a high
temperature or humidity area.
This product must be earthed.
Read the instruction inthis manual carefully andthoroughly, asthey give important
information regarding safety during use and maintenance. Keep this manual with
the unit, in order to consult it in the future. If the unit is sold or given to another
operator, make certainthat it always has itsmanual, to enable the new owner to
read about its operation and re lative instructions.
Features General Instructions
Thank you for your purchase.
This product features include:
1 2
WARNING
CAUTION
4 channel chaser with 16 built-in programs and 6 operating modes:
MANUAL DIMMER/MANUAL PROGRAM/ AUTO PROGRAM/
HOLD SOUND/ PROG. SOUND/ AUTO SOUND.
4 channel MIDI pack with 4 individual Note Numbers
4 channel DMX dimmer pack with 4 individual DMX addresses
Normal/Cross dimmer
Forward/Reverse chasing direction
Fade Time control
Preheat function
Manual override
Built-in microphone for Music triggering
Power failure memory
All manuals and user guides at all-guides.com
DO NOTdismantle or modify the unit.
Packaging material (plastic bags, polystyrenefoam, nails, etc.) MUST NOT be left
within children's reach, as itcan be dangerous.
After having removed thepackaging check that theunit is NOT damaged in any way.
If in doubt,DON'T use it and contactan authorized dealer.
This unit is intendedfor indoor use only.
NEVER try to repair the unit yourself. Repairs by unqualified people could cause
damage or faulty operation. Contact your nearest dealer.
Wait for at least one second to turn on the power after turning off this unit.
DO NOT open the unit--there are no user serviceable parts inside.
Take care not to damage the power cord.
STOP using the unit immediately In the event of serious operation problems and
either contact your localdealer for a checkor contact us directly.
DO NOT make any inflammable liquids, water or metal objects enter the unit.
To prevent fire or shock hazard, do not expose this product under a high
temperature or humidity area.
This product must be earthed.
Read the instruction inthis manual carefully andthoroughly, asthey give important
information regarding safety during use and maintenance. Keep this manual with
the unit, in order to consult it in the future. If the unit is sold or given to another
operator, make certainthat it always has itsmanual, to enable the new owner to
read about its operation and re lative instructions.
Features General Instructions
Thank you for your purchase.
This product features include:
1 2
WARNING
CAUTION
4 channel chaser with 16 built-in programs and 6 operating modes:
MANUAL DIMMER/MANUAL PROGRAM/ AUTO PROGRAM/
HOLD SOUND/ PROG. SOUND/ AUTO SOUND.
4 channel MIDI pack with 4 individual Note Numbers
4 channel DMX dimmer pack with 4 individual DMX addresses
Normal/Cross dimmer
Forward/Reverse chasing direction
Fade Time control
Preheat function
Manual override
Built-in microphone for Music triggering
Power failure memory
All manuals and user guides at all-guides.com
1. Overview 1. Overview
3 4
5. DMX IN
7. MIDI IN
6. DMX Out
8. MIDI THRU
9. Channel Fuse
This connector receives DMX signal.
This connector receives MIDI signal.
This connector sends DMX signal.
This connector sends MIDI signal through to
the next MIDI device.
F10A 250V 5x20mm
Control Board
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
2
1
9
PUSH
3
4
5
6
783. Power Input
2. Control Board
1. Channel Output
NAC3MPA by Powercon, 250V, 20A
This control board is used to set this unit
via these function buttons.
10 A/CH., Total 20 A max.
4. Foot control connector 1/4 inch stereo phone jack
All manuals and user guides at all-guides.com
all-guides.com
1. Overview 1. Overview
3 4
5. DMX IN
7. MIDI IN
6. DMX Out
8. MIDI THRU
9. Channel Fuse
This connector receives DMX signal.
This connector receives MIDI signal.
This connector sends DMX signal.
This connector sends MIDI signal through to
the next MIDI device.
F10A 250V 5x20mm
Control Board
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
2
1
9
PUSH
3
4
5
6
783. Power Input
2. Control Board
1. Channel Output
NAC3MPA by Powercon, 250V, 20A
This control board is used to set this unit
via these function buttons.
10 A/CH., Total 20 A max.
4. Foot control connector 1/4 inch stereo phone jack
All manuals and user guides at all-guides.com
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
2. Operation Guide2. Operation Guide
2.2 DMX Mode
2.3 MIDI Mode
2.1 Mode Select
2.2 DMX Mode
5 6
Press and hold down F button first, tap the
Signal Select button, the Segment Display
shows "IN".
Keep pressing F button, tap the DMX /MIDI
button to select DMX or MIDI mode,
corresponding LED indicates the current
mode.
While holding down F button, tap Signal
Select button, when the Segment Display
shows"OUT", Master LED lights indicating
Master mode is active.
1. Tap the channel button(Ch1-Ch4), the
corresponding channel LED blinks indicating
your selection and the Segment Display shows
the DMX address of the channel.
1. Tap the channel button(Ch1-Ch4), the
corresponding channel LED blinks indicating
your selection and the Segment Display shows
the Note Number of the channel.
2. Tap the Up/Down button to select your desired
DMX address from 001 to 512.
3. Once you've set the DMX address, tap the
channel button a second time to store your
setting into memory.
4. Continue steps 1-3 until you've set the
addresses all 4 channels.
When the Segment Display shows "IN" and the DMX LED lights, this unit serves
as a 4 channel DMX dimmer pack. The Signal LED blinks when DMX signal is
available.
When the Segment Display shows "IN" , , tap DMX /MIDI
button causing the MIDI LED lights up, which indicates MIDI mode is active. The
Signal LED blinks when MIDI signal is available.
while holding down F button
All manuals and user guides at all-guides.com
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
2. Operation Guide2. Operation Guide
2.2 DMX Mode
2.3 MIDI Mode
2.1 Mode Select
2.2 DMX Mode
5 6
Press and hold down F button first, tap the
Signal Select button, the Segment Display
shows "IN".
Keep pressing F button, tap the DMX /MIDI
button to select DMX or MIDI mode,
corresponding LED indicates the current
mode.
While holding down F button, tap Signal
Select button, when the Segment Display
shows"OUT", Master LED lights indicating
Master mode is active.
1. Tap the channel button(Ch1-Ch4), the
corresponding channel LED blinks indicating
your selection and the Segment Display shows
the DMX address of the channel.
1. Tap the channel button(Ch1-Ch4), the
corresponding channel LED blinks indicating
your selection and the Segment Display shows
the Note Number of the channel.
2. Tap the Up/Down button to select your desired
DMX address from 001 to 512.
3. Once you've set the DMX address, tap the
channel button a second time to store your
setting into memory.
4. Continue steps 1-3 until you've set the
addresses all 4 channels.
When the Segment Display shows "IN" and the DMX LED lights, this unit serves
as a 4 channel DMX dimmer pack. The Signal LED blinks when DMX signal is
available.
When the Segment Display shows "IN" , , tap DMX /MIDI
button causing the MIDI LED lights up, which indicates MIDI mode is active. The
Signal LED blinks when MIDI signal is available.
while holding down F button
All manuals and user guides at all-guides.com
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
2.3 MIDI Mode
2. Tap the Up/Down button to select the Note
Number from 001 to 128.
3. Once you've selected the Note Number, tap
the channel button a second time to store your
setting into memory.
4. Continue steps 1-3 to set Note Number of the
other channel.
2. Operation Guide
2.4 Master Mode
When the Segment Display shows "OUT" and the
Master LED lights, this unit serves as a 4 channel
DMX chaser.
Keep pressing F button, tap Mode button several
times to select chase mode from Manual Dimmer/
Manual Program/Auto Program/Auto Sound/Prog.
Sound/Hold Sound, corresponding LED indicates
your selection.
2. Operation Guide
2.4 Master Mode
Manual Dimmer Manual Dimmer LED is on, you can adjust the intensity
of individual of 4 channels using CH 1-4 and UP/DOWN
buttons.
Manual Program Manual Program LED is on, you can select any of 16
preset programs to chase.
Auto Program Auto Program LED is on, every of 16 programs will be
executed 8 times in sequence.
Hold Sound Hold Sound LED is on, channels 1-4 are controlled by
music rhythms detected by built-in microphone, its
sensitivity can be adjusted.
Prog Sound Prog Sound LED is on, the programs are executed by
Bass, 16 preset programs are selectable.
Auto Sound Auto Sound LED is on, every of 16 programs will be
Keep pressing F button, tap Preset button
several times to change functions between
Fade Time/Dimmer/Preheat/Speed/Program
/MIDI channel.
Fade Time The Segment Display shows "F"
followed by three numbers 000-
100. Tap Up/Down button to set
fade time from instant to 60 seconds.
2.5 Preset Functions
7 8
All manuals and user guides at all-guides.com
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
2.3 MIDI Mode
2. Tap the Up/Down button to select the Note
Number from 001 to 128.
3. Once you've selected the Note Number, tap
the channel button a second time to store your
setting into memory.
4. Continue steps 1-3 to set Note Number of the
other channel.
2. Operation Guide
2.4 Master Mode
When the Segment Display shows "OUT" and the
Master LED lights, this unit serves as a 4 channel
DMX chaser.
Keep pressing F button, tap Mode button several
times to select chase mode from Manual Dimmer/
Manual Program/Auto Program/Auto Sound/Prog.
Sound/Hold Sound, corresponding LED indicates
your selection.
2. Operation Guide
2.4 Master Mode
Manual Dimmer Manual Dimmer LED is on, you can adjust the intensity
of individual of 4 channels using CH 1-4 and UP/DOWN
buttons.
Manual Program Manual Program LED is on, you can select any of 16
preset programs to chase.
Auto Program Auto Program LED is on, every of 16 programs will be
executed 8 times in sequence.
Hold Sound Hold Sound LED is on, channels 1-4 are controlled by
music rhythms detected by built-in microphone, its
sensitivity can be adjusted.
Prog Sound Prog Sound LED is on, the programs are executed by
Bass, 16 preset programs are selectable.
Auto Sound Auto Sound LED is on, every of 16 programs will be
Keep pressing F button, tap Preset button
several times to change functions between
Fade Time/Dimmer/Preheat/Speed/Program
/MIDI channel.
Fade Time The Segment Display shows "F"
followed by three numbers 000-
100. Tap Up/Down button to set
fade time from instant to 60 seconds.
2.5 Preset Functions
7 8
All manuals and user guides at all-guides.com
all-guides.com
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
2.6 Chase Direction
2.7 Cross and Normal Dimmer
2. Operation Guide
Keep pressing F button, tap button to select
chase direction, the Segment Display shows
"L--" or "R--". "L--" indicates the programs will
chase from left to right, and "R--" indicates the
programs will chase from right to left.
Keep pressing F button, tap D/S button to select
dimmer mode from Cross / Normal dimmer.
The Segment Display shows "CRO" when cross
dimmer is active. In Cross mode, if channel intensity
is 50%(>50%) , the fixture will be fully on; if channel
intensity is less than 50%, the fixture will be fully off.
The Segment Display shows "NOR" when normal
dimmer is active. In Normal mode, you can adjust
the intensity using UP/DOWN button.
2. Operation Guide
2.5 Preset Functions
Master
Dimmer
or
Channel
Dimmer
Preheat
Program
Speed
MIDI
Channel
The Segment Display shows "d"
followed by three numbers 000-
100. Tap Up/Down button to
adjust intensity from fully off(000)
to fully on(100).
The Segment Display shows "E"
followed by two numbers 00-25.
Tap Up/Down button to adjust from
0% intensity to 25% intensity.
The Segment Display shows "CH"
followed by two numbers 01-16.
Tap Up/Down button to select
your desired MIDI Channel.
The Segment Display shows "P"
followed by two numbers 01-16.
Tap Up/Down button to select
desired chase program.
The Segment Display shows "SP"
followed by two numbers 01-99.
Tap Up/Down button to select
desired chase speed. 01 will give
a slowest speed, 99 will give a
fastest speed.
E:00
sp:0i
910
All manuals and user guides at all-guides.com
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
2.6 Chase Direction
2.7 Cross and Normal Dimmer
2. Operation Guide
Keep pressing F button, tap button to select
chase direction, the Segment Display shows
"L--" or "R--". "L--" indicates the programs will
chase from left to right, and "R--" indicates the
programs will chase from right to left.
Keep pressing F button, tap D/S button to select
dimmer mode from Cross / Normal dimmer.
The Segment Display shows "CRO" when cross
dimmer is active. In Cross mode, if channel intensity
is 50%(>50%) , the fixture will be fully on; if channel
intensity is less than 50%, the fixture will be fully off.
The Segment Display shows "NOR" when normal
dimmer is active. In Normal mode, you can adjust
the intensity using UP/DOWN button.
2. Operation Guide
2.5 Preset Functions
Master
Dimmer
or
Channel
Dimmer
Preheat
Program
Speed
MIDI
Channel
The Segment Display shows "d"
followed by three numbers 000-
100. Tap Up/Down button to
adjust intensity from fully off(000)
to fully on(100).
The Segment Display shows "E"
followed by two numbers 00-25.
Tap Up/Down button to adjust from
0% intensity to 25% intensity.
The Segment Display shows "CH"
followed by two numbers 01-16.
Tap Up/Down button to select
your desired MIDI Channel.
The Segment Display shows "P"
followed by two numbers 01-16.
Tap Up/Down button to select
desired chase program.
The Segment Display shows "SP"
followed by two numbers 01-99.
Tap Up/Down button to select
desired chase speed. 01 will give
a slowest speed, 99 will give a
fastest speed.
E:00
sp:0i
910
All manuals and user guides at all-guides.com
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
3. Technical Specifications
Power Input ...................................................... AC 120V~50-60Hz
Channel Output ...................................................10A/CH., Total 20A
DMX In/Out .............................. 3 pin female & male XLR socket x1
MIDI In/Thru ..................................................... 5 pin multiple socket
Channel Fuse ..................................... F10A 250V 5x20mm (x4PCS)
Dimensions .............................................................. 1320x60x80mm
Weight(approx) ........................................................................ 4.3 kg
2.8 Link Up
2.9 Initialization
2. Operation Guide
Several units can be linked up using DMX cables. When linking, make sure only
one unit works in Master mode, and the other units will work depending on the
master unit.
Press F, Signal Select and DMX/ MIDI buttons
at a time, this unit will initialize its memory, the
Segment Display goes out. Release all three
buttons, this unit will return to default setting, the
Segment Display shows "IN", and Manual Dimmer
LED is on.
11 12
All manuals and user guides at all-guides.com
Signal Select DMX/MIDI
Ch.1 Ch.2
D/S
Ch.3
Mode
Ch.4
Preset
MIDI
Master
DMX
Signal
Manual Dimmer
Manual Program
Auto Program
Hold Sound
Prog Sound
Auto Sound
Audio Sen.
MaxMin
1 2 3 4F
Stand By
3. Technical Specifications
Power Input ...................................................... AC 120V~50-60Hz
Channel Output ...................................................10A/CH., Total 20A
DMX In/Out .............................. 3 pin female & male XLR socket x1
MIDI In/Thru ..................................................... 5 pin multiple socket
Channel Fuse ..................................... F10A 250V 5x20mm (x4PCS)
Dimensions .............................................................. 1320x60x80mm
Weight(approx) ........................................................................ 4.3 kg
2.8 Link Up
2.9 Initialization
2. Operation Guide
Several units can be linked up using DMX cables. When linking, make sure only
one unit works in Master mode, and the other units will work depending on the
master unit.
Press F, Signal Select and DMX/ MIDI buttons
at a time, this unit will initialize its memory, the
Segment Display goes out. Release all three
buttons, this unit will return to default setting, the
Segment Display shows "IN", and Manual Dimmer
LED is on.
11 12
All manuals and user guides at all-guides.com
A Division of the American DJ Group of Companies
4295 Charter Street Los Angeles, CA 90058 USA
Tel: 323-582-3322 Fax: 323-582-3311
Web: www.elationlighting.com
Elation Professional R
24-004-1529
Rev1.1
All manuals and user guides at all-guides.com
all-guides.com
Other manuals for PRO BAR 4
1
Table of contents
Other Elation Dj Equipment manuals
Elation
Elation DW PENDANT User manual
Elation
Elation PALADIN CUBE User manual
Elation
Elation CUEPIX 16IP User manual
Elation
Elation FUZE WASH Z350 User manual
Elation
Elation SIX PAR Z19 IP User manual
Elation
Elation DMX-512 User manual
Elation
Elation ARISTE MONET EAM990 User manual
Elation
Elation DTW BLINDER 700 IP User manual
Elation
Elation ZCL BAR Z300 IP User manual
Elation
Elation Artiste Monet User manual
Elation
Elation IMAGE PRO 300 User manual
Elation
Elation Flex LED Tape WP User manual
Elation
Elation Proteus Lucius User manual
Elation
Elation CYBER PAK User manual
Elation
Elation RDMX6S User manual
Elation
Elation FUZE PAR Z120 IP User manual
Elation
Elation SIXPAR 300 User manual
Elation
Elation DESIGN SPOT 575E User manual
Elation
Elation DMX Operator 192 User manual
Elation
Elation PLATINUM SPOT LED PRO II User manual
