eLdrim eLR1-868H2 User manual

1
Thank you for purchasing the eLR1-868 radio receiver; we hope that you will be pleased with our
product. Our company makes every effort to ensure top-quality products that can be used for a long
time without failure.
NOTE
eLR1-868H2 cooperates with transmitters working at a 868.3MHz frequency and compatible with
Keeloq standard. It can memorize up to 42 remotes.
eLR1-868H2M cooperates with transmitters working at a 868.3MHz frequency and compatible with
Keeloq standard. It can memorize up to 1000 remotes.
eLR1-868Sreceiver was designed for use with transmitters:
Marantec Digital (868.3MHz, FIXED-CODE)
Hormann (868.3MHz FIXED-CODE –grey enclosure, blue buttons )
It can memorize up to 32 remotes.
eLR1-868H2/eLR1-868H2M/eLR1-868S
INTRODUCTION
USER’S MANUAL

2
In accordance with the provisions of Directive 2006/42/EC on machinery, we declare that the product must not be
put into service until the final machinery into which it is to be incorporated has been declared in conformity with
directives and relevant provisions which must be met by the final machinery.
MARKING
NOTES
1.2.1-H
R1:1.0.7/3.0.0
eLR1-868H2
1.3.0-H
R1:1.0.8/3.0.0
eLR1-868H2M
2.0.0-H1M
R1:1.0.5/6.0.0
eLR1-868S
An excellent superheterodyne receiver with double interference filtering.
Non-volatile memory in remote controls.
Easy installation, learning and configuration procedure.
Operation in the bistable and monostable mode for channel CH2.
Option to connect an external antenna.
All the activities relating to installation of the driver should be carried out when the device to which we want to
incorporate the receiver is powered off.
The first step of the installation is to assemble the mechanical radio receiver, then to connect the outputs and supply voltage.
In accordance with the applicable regulations on disposal of redundant equipment by private users
in the European Union, any items with such a symbol MUST NOT BE disposed of with other waste.
In this case the user is responsible for proper disposal by delivering the device to a designated
point, or to the manufacturer, which will handle further disposal. Separate collection and recycling
of redundant equipment help to protect the environment and ensure that disposal is carried out in
such a way as to protect human health and the environment. The note also applies to used
batteries and accumulators.
ADVANTAGES OF eLR1-868 RECEIVER
CONNECTION
SOFTWARE

3
Programming is carried out by the light emitting diode (LED) and the touch button located on the plate, in the field
marked with a circle and a dot, and the symbol CH1/2.
Transmitter button for CH1.
Press and release the touch button (for less than 3 sec.), the LED will begin to flash. The LED will flash for 5 sec. At this time
press the selected button you want to program for the device on the remote control. If the remote control has been
programmed properly the LED will flash 3 times. The receiver will remain in the remote control programming mode, which will
be indicated by LED flashing. To program another remote control, push the selected key on it. The LED will again flash 3
times, etc. When the LED flashes 2 times, it means that the memory is already full, whereas 1 flash means that the receiver
has left the remote control programming mode and returned to its normal operation. After programming all remote controls
you can exit the programming by briefly pressing the touch button, or the receiver will automatically exit the programming
mode after 5 seconds, which will be confirmed by 1 flash of the LED.
Transmitter button for CH2.
Press and hold the CH1/2 button, the LED will light up, then go out, which indicates that the CH1/2 button should be released.
When you release the button, the LED will begin to flash. The LED will flash for 5 sec. At this time press the selected button
you want to program for the device on the remote control. If the remote control has been programmed properly the LED will
flash 3 times. The receiver will remain in the remote control programming mode, which will be indicated by LED flashing. To
program another remote control, push the selected key on it. The LED will again flash 3 times, etc. When the LED flashes 2
times, it means that the memory is already full, whereas 1 flash means that the receiver has left the remote control
programming mode and returned to its normal operation. After programming all remote controls you can exit the programming
by briefly pressing the touch button, or the receiver will automatically exit the programming mode after 5 seconds, which will
be confirmed by 1 flash of the LED.
Deleting all transmitters from the receiver memory.
Press and hold the CH1/2 button. At this time the LED should light up, go out, then flash 3 times. Release the CH1/2 while the
LED is flashing, it will light up again. Now you need to press and hold the CH1/2 button within 3 seconds until the LED flashes
3 times again and goes out. All transmitters have been removed from the receiver memory.
NOTE.
It is possible to change the control keys of a pre-programmed remote control by re-programming other key on the remote
control. When you are programming changes remember that the unprogrammed key will replace the previously programmed
key. After reprogramming, the key previously programmed on one channel will begin to work in other mode. You can also
delete all the keys from one of the selected channels. You must enter one of the three remote control button modes; when the
LED is flashing press and hold the CH1/CH2 touch button again until the LED lights up and blinks 3 times, then release the
button. All the keys in the selected feature have been deleted.
OK
PROGRAMMING
It is possible to supply the
eLR1-868 receiver with a
voltage of 12V. To do this,
connect the solder points
marked with the letter "A".

4
Bistable mode.
eLR-868 receivers have the option to configure the CH2 output as monostable or bistable; to switch the CH2 channel to the
bistable mode change the position of the DP1 to ON. The DP1 switch in the OFF position changes the CH2 output to the
monostable mode.
Please read all warnings and safety rules before attempting to assemble and use the receiver.
Do not connect power supply earlier than indicated in the manual.
The device should be stored and installed in locations inaccessible to children.
All the operations associated with the installation (connection, start-up, operation) must be carried out in
accordance with the applicable rules on operation of electrical equipment and the occupational health and safety
rules.
The type of electrical system and its protection against electric shock are specified in the standards.
All the operations can be performed only by properly authorised persons.
The device must be connected in accordance with the attached description/diagram
Frequency:
868.3MHz
Modulation:
OOK
Range:
up to150m
Transmission:
eLR1-868S –fix code
eLR1-868H2(M) –Keeloq
Power supply:
15-24V ( depends on
configuration)
Current
consumption:
12/60 mA (maximum)
Outputs:
NO / two / 1A/30Vdc (max
power 62,5VA/30W)
Temperature range:
-20ºC / +70ºC
Dimensions:
47x67x24mm
Weight:
41g
Enclosure:
IP40
SPECIFICATION
PRECAUTIONS AND SAFETY RECOMMENDATIONS
CONFIGURATION
Distributor / Seller