ElectrIQ DOGCAM720 User manual

WIRELESS IP CAMERA
SETUP AND USER MANUAL
Thank you for choosing electriQ.
Please read this user manual before using this item and
keep it safe for future reference .
Visit our page www.electriQ.co.ukfor our entire range of
electricals

IMPORTANT SAFETY INSTRUCTIONS
Read all instructions. All user guidelines must be
read before the device is used.
Retain the instructions for further use.
For indoor use only. Do not position the unit
where it would be subjected to extreme moisture,
temperature, or dust.
Do not use in bathrooms or other humid places.
There are no user maintainable parts, do not
attempt to disassemble or repair.
Do not place the device near a heat source, or
expose to direct sunlight.

INTRODUCTION
Thank you for purchasing an electriQ Wifi controlled device.
INSTALLATION OF APP
Before installation download the YOOSEE app either using the
QR codes below or searching in your chosen app store.
ANDROID IOS
REGISTER WITH THE APP
Once the app has loaded
select the option for Quick
Register.

You will then be prompted to
register using your mobile
phone number or email address,
verify the address / phone
number given and create a
password (Enter the password
in both boxes)
A verification code will be sent to
your phone or email which must
be input into the app to complete
registration.
The password must be at least 8 characters and contain letters
and numbers. Once your password and verification number
have been entered, press Confirm
Please note: When registering / logging in using your phone
number the 0 should be removed from the start of your phone
number. e.g. If your phone number is 07123456789, enter
7123456789.
LOG INTO THE APP
Enter your email address or phone
number (depending how you originally
registered) and password into the
main screen and press thelogin button

CONNECTING THE CAMERA TO YOUR WIRELESS
NETWORK
Ensure your camera and mobile are situated close to the router
so they both recieve a good WIFI signal.
Connect your phone to your 2.4ghz wireless network. (To
ensure your phone is connected to your router correctly it is
advisable to disable mobile data, and check access to the
internet using your phones browser)
Plug the camera into the mains
(ensuring it is still close to the
router).
Wait for around 30 seconds until the
camera starts to bleep (single bleep
at 10 second intervals)
If after 30 seconds the camera does
not start to bleep: Reset the camera by
inserting a pin into the RESET hole on
the underside of the camera for 5
seconds until the unit makes a noise.
Then leave for 30 seconds until the
camera bleeps.
Please note the camera can only be connected to a 2.4ghz
network. If your router is also able to operate at 5ghz
(Dualband), the 2.4ghz MUST be given a different name
(SSID) to the 5ghz network and the connection made to the
2.4ghz network only. Fursther details on changing the SSID
of your router are available from your ISP / Router
manufacturer.

Once the camera is bleeping, return to
the app on your phone and press the +
icon in the top right hand corner
Press the option to “Add new device”
Press the option for Fast
Networking.
Select your 2.4ghz WIFI network
from the drop down list and enter
the password for your network.
(This is usually found on a sticker
on the side or back of the router
unless it has been changed).

Press on the access point
created by the camera which
will be labelled “GM_AP_******”
The phone will then disconnect
from your wifi network, and will
connect to the network created
If the app is unable to create the
connection, it will bring up a message,
asking you to swap the internet
connection manually. To do this exit the
app, disconnect from your wifi network,
and connect to the hotspot created by
the camera which will be labelled
“GM_AP_******” before going back to
the app to continue setup.
When the camera bleeps to indicate it
has successfully connected, press the
blue Confirm button at the bottom
You will then receive the message
showing installaion was successful.
Press confirm to proceed to the main
viewing screen.

USING THE APP - OVERVIEW
ALL DEVICE SCREEN
1: Scan QR code from friend for
device sharing
2: Change the name of the
camera
3: Add a new camera
4: Share device with a friend /
create QR code
5: N/A
6: Playback from SD card in
camera
7: Camera Settings
8: List devices paired with App
9: Alarm Push Information
10: Access images and videos saved to phone.
11: App Settings
12: View Camera (See Below)
CAMERA VIEW
SCREEN
1: Return to All Device
Screen
2: Device Settings
3: Preset Position
Marker
4: Video Quality
5: Full Screen Mode
6: Record Video to
Phone
7: Intercom
8: Screenshot to
Phone
9: Speaker On/Off
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9

While on the camera view screen you can pan and tilt the image
by sliding your finger across the image. A pinch action can also
be used to zoom in and out on the image.

ALL DEVICES SCREEN
SHARING THE DEVICE WITH FRIENDS AND FAMILY
Once your camera is set up it can be
shared using Button 4 on the All
Devices screen. This will create a QR
code which can then be scanned on
the other persons phone.
It will also create a web link that can
be emailed to a PC to allow access to
the camera through the CMS app.
To scan the code, they must log into
the app under their own user account,
and then press the buttd.n labelled as
1 on the All Devices screen to scan the
QR code you have create.
PLAYBACK FROM SD CARD
By pressing Button 6 on the All devices
screen you are able view videos that
have been recorded to the SD card
within the camera (Standard SD card
upto 32gb available seperately)
From the playback screen, select which video file you would like
to view, which will then load the playback screen with basic
controls.
Example

CAMERA SETTINGS
The camera settings can be accessed
using button 7 in the All Devices Screen.
Device Information: Shows details of
the camera’s firmware and internet
connection
Time Settings: Allows the timezone
and time to be changed.
Picture and Sound: Allows the Video
format to be changed between PAL and
NTSC. The volume of the camera to be
changed, The motion sensor to be
turned on and the image to be reversed.
Security Settings: Allows a RTSP password to be set to
prevent unauthorised access to the camera.
Network settings: Allows the connection type of the camera to
be changed between wireless and wired.
Alarm Settings: Allows the camera to be set up to trigger an
alarm upon motion detection. This includes setting the camera
up to send an email using a suitable account, logging an alert
with the app, and/or sounding a buzzer.
Record Settings: Allows the recording options to be changed
between manual recording, Timer recording, or only recording
upon motion detection.
Firmware Update: Update the camera to the latest firmware
Unbind Devices: Unlink the camera from the app.

APP SETTINGS
The App Settings can be accessed using
Button 11 on the All Devices Screen.
System Settings: Allows the settings for
the system to be changed. This includes
autostarting the app when your phone is
started, Default settings for monitoring via
the app, and changing the response of
the phone when the alarm is triggered.
Help and Feedback: List common
issues, information on their causes and
how to resolve them.
ALARM PUSH INFORMATION
By pressing Button 9 on the All Devices Screen you can view a
log of alarm events on the camera. When the motion detection
is set up on the cameras details of any activattions can be
viewed on this screen.

ACCESSING THE CAMERA WITH A PC
The camera can also be accessed on a windows PC using the
CMS app available from http://www.yoosee.co . Before
installing the app, ensure the camera is connected to the same
network as your computer, either by first following the setup
through the app.
Download the app, and extract the zip file. Then double click
the CMSSetup exe file and running the setup. The on screen
instructions will guide you through the installation process.
Once the software is installed,
open the program (CMSClient)
which will load to the login screen.
Leave the password blank and
press OK to load the monitoring
software.
The software will then search for
cameras conneced to your
network, and give you the option
to add it automatically. Press
“add all” to confirm add the
camera to the software.
To view the camera double click
on the device on the Device List
to load the camera view into one
of the preview squares. To
select which square the camera
is displayed in, click on the
required preview square before
double clicking on the device

CONTROLS
Preview: View what is currently been recorded by the
cameras connected.
Playback: View what has been recorded through the
app. Allows the date and time of the recording to be
selected.
Log: View events that have happened on the camera
/App.
Settings: View and change the settings for the CMS
software, including adding, modifying and removing
users.
Lock: Lock and Unlock the app to leave it open /
running while still preventing unauthorised access.
PREVIEW SCREEN
Add / Remove Camera: Gives the option to add or
remove cameras automatically or manually
Pan and Tilt: Use to move the camera.
Within the preview screen you can also
right click on a video feed to choose
options such as start recording, and
capture an image.

Mute: Turn sound on / off from the chosen camera.
Screen PTZ: Change between using the controls on
the left to pan and tilt the camera, and been able to
drag the mouse on the picture to pan and tilt.
Page Left and Right: Scroll through the
pages of camera views from Camera 1
onwards.
Full Screen Mode: Toggle between the normal view
and full screen mode.
Windows: Select the number
of windows that are visible on
the screen
Right clicking on the video stream brings up a menu allowing
recording of footage directly to the PC, saving a screenshot to
the PC, and changing the resolution of the vidio dispayed.
PLAYBACK SCREEN
Open File: Allows AVI Files that have been saved
to the computer to be played back
Rewind, Play, Fast
Forward, Stop.
Convert to mp4: Video from the app can be backed
up and converted to an MP4 for export out of the
software.

PLAYBACK THROUGH PC
Through the app, you are able to playback videos recorded both
within the app onto the PC, and footage saved on the camera
itself.
PLAYBACK OF RECORDINGS ON THE PC
On the left hand side of the screen
select the date you require to view, and
press the search button below.
A Green bar will be displayed at the
bottom to show available recordings.
Tick the box next to the camera(s) you
want to view and left click on the green
bar around the time you require to view.
The video will start to playback.
PLAYBACK OF RECORDINGS ON THE CAMERA
Change the drop down box to Remote
record files. Type the start and end date
and times of the recording you are
searching for and press the search button.
All matching recordings will be displayed
in the box below. Double click on the vide
you would like to view. The video will
then start to play, after downloading a
portion from the camera.

Due to a process of continual product improvement, and the
different devices supported, some images contained within this
manual may differ from your version. We cannot guarentee the
availability of all features described on all platforms and
hardware combinations.
electriQ UK SUPPORT
www.electriQ.co.uk/support
Service Line: 0871 620 1057
Office hours: 9AM - 5PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA
Disposal: Do not dispose this product as
unsorted municipal waste. Collection of such
waste must be handled separately as special
treatment is necessary.
Recycling facilities are now available for all customers at
which you can deposit your old electrical products.
Customers will be able to take any old electrical equipment
to participating civic amenity sites run by their local
councils. Please remember that this equipment will be
further handled during the recycling process, so please be
considerate when depositing your equipment. Please
contact the local council for details of your local household
waste recycling centres.U