Electro-Voice XLC215 User manual

Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8
Output Label Xlc 118 127+ LF 127+ MB 127+ HF Xlc 118 127+ LF 127+ MB 127+ HF
Output Delay 1.85ms 916.67us 562.5us 0s 1.85ms 916.67us 562.5us 0s
Polarity Invert no no no no no no no no
Output Gain 0dB 1dB -5dB -6dB 0dB 1dB -5dB -6dB
HP Filte
r
Type BW24 LR24 LR24 LR24 BW24 LR24 LR24 LR24
Frequency 33.7Hz 100Hz 500Hz 1.6kHz 33.7Hz 100Hz 500Hz 1.6kHz
LP Filte
r
Type LR24 LR24 LR24 BW24 LR24 LR24 LR24 BW24
Frequenc
y
100Hz 500Hz 1.6kHz 16kHz 100Hz 500Hz 1.6kHz 16kHz
All-Pass Filte
r
Frequency
Slope off off off off off off off off
Q
Filter 1
Filter Type PEQ PEQ PEQ PEQ PEQ PEQ PEQ PEQ
Frequency 37.4Hz 125Hz 227Hz 1kHz 37.4Hz 125Hz 227Hz 1kHz
Q2.87 2.04 2.87 4.8 2.87 2.04 2.87 4.8
Gain 4dB 2dB 2dB -6dB 4dB 2dB 2dB -6dB
Filter 2
Filter Type PEQ PEQ PEQ PEQ PEQ PEQ PEQ PEQ
Frequency 200Hz 484Hz 650Hz 2.27kHz 200Hz 484Hz 650Hz 2.27kHz
Q0.92 2.87 1.78 1.78 0.92 2.87 1.78 1.78
Gain -2dB 1dB -3dB -12dB -2dB 1dB -3dB -12dB
Filter 3
Filter Type PEQ PEQ PEQ PEQ PEQ PEQ PEQ PEQ
Frequency 800Hz 591Hz 2.13kHz 4.84kHz 800Hz 591Hz 2.13kHz 4.84kHz
Q1.41 1.78 2.87 1.78 1.41 1.78 2.87 1.78
Gain -8dB -9dB 3dB -2dB -8dB -9dB 3dB -2dB
Filter 4
Filter Type PEQ PEQ PEQ PEQ PEQ PEQ
Frequency 1.21kHz 2.2kHz 14.5kHz 1.21kHz 2.2kHz 14.5kHz
Q2.87 4.8 1.58 2.87 4.8 1.58
Gain -4dB -4dB 6dB -4dB -4dB 6dB
Filter 5
Filter Type PEQ PEQ PEQ PEQ
Frequency 750Hz 826Hz 750Hz 826Hz
Q4.8 7.21 4.8 7.21
Gain 1dB -1dB 1dB -1dB
Filter 6
Filter Type
Frequency
Q
Gain
Compressor
Threshold (dBu)
Ratio (N to 1)
Insert (In/Out) out out out out out out out out
Attack (us)
Release (ms)
Knee (Hard/Soft)
Limiter
Threshold (dBu) 2dBu 0dBu 0dBu -2dBu 2dBu 0dBu 0dBu -2dBu
Release (ms) 200ms 150ms 20ms 3ms 200ms 150ms 20ms 3ms
Xlc127+3W118 DN9848(e) P3000 0dBu V2.6
Output levels and limiter settings assume equal amplifier power to each passband with amplifier input sensitivity of 0dBu
Notes: DN9848e and DN9848 with firmware V4.01 and higher have the ability to toggle between Q and BW for parametric filters. DN9848
with firmware V3.05 and older only use BW, use attached conversion spreadsheet to convert. Do not adjust output filters, use input filters for
room and system tuning. DN9848 with firmware V3.05 and older has a maximum of 100ms release time for limiters. For these versions,
change Subwoofer and LF release times to 100ms.

Q value BW value Q value BW value
18.03 0.08 1.78 0.8
14.42 0.1 1.58 0.9
7.21 0.2 1.41 1
4.8 0.3 1.17 1.2
3.6 0.4 0.92 1.5
2.87 0.5 0.67 2
2.39 0.6 0.511 2.5
2.04 0.7 0.4 3
DN9848e BW to Q conversion