Electro-Voice ZxA5-90 User manual

ZxA5 Series
Owner’s Manual
ZxA5-60
ZxA5-90

Im
p
o
r
tant Sa
f
et
y
Instructions
The lightning flash with arrowhead symbol, within an equilateral triangle i
s
intended to alert the user to the presence of uninsulated “dangerou
s
voltage” within the product’s enclosure that may be of sufficien
t
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateraltriangleis intended to alert
the user to the presence of important operating and maintenance
(
servicin
g)
instructions in the literature accom
p
an
y
in
g
the a
pp
liance.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean onl
y
with a dr
y
cloth.
The asterisk within an equilateral triangle is intended to inform the user t
o
necessary installation or removal instructions regarding equipment o
r
hardware use relatin
g
to the s
y
stem.
7. Do not block any ventilation openings. Ins
t
all in accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped
14. To completely disconnect AC power from this apparatus, the power supply cord must be unplugged.
15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on this
apparatus.
16. TheAC plug of the power supply cord shall remain readily operable.
Caution: Do not exceed the marked rating of the AC Output.
Example: If each additional unit is rated 3A,a maximum of 3 units can be connected for a total of 9A.
Management of WEEE (waste electrical and electronic equipment) (applicable in Member States of the European Union and other
European countries with individual national policies on the management of WEEE) The symbol on the product or on its packaging
indicates that this product may not be treated as regular household waste, but has to be disposed through returning it at a Telex
dealer.
Important Service Instructions
C
A
UTION:These servicing instructions are
f
or use by qualified personnel onl
y
.
T
oreducetherisko
f
electric shock, do not
perform any servicing other than that contained in the Operating Instructions unless you are qualified to do so. Refer all
servicing to qualified service personnel.
1. Security regulations as stated in the EN 60065 (VDE 0860 / IEC 65) and the CSAE65 - 94 have to be obeyed when servicing the appliance.
2. Use of a AC separator transformer is mandatory during maintenance while the appliance is opened, needs to be operated and is
connected to the AC.
3. Switch off the power before retrofitting any extensions, changing theAC voltage or the output voltage.
4. The minimum distance between parts carryingAC voltage and any accessible metal piece (metal enclosure), respectively between
the AC poles has to be 3 mm and needs to be minded at all times.
The minimum distance between parts carryingAC voltage and any switches or breakers that are not connected to theAC (secondary
parts) has to be 6 mm and needs to be minded at all times.
5. Replacing special components that are marked in the circuit diagram using the security symbol (Note) is only permissible when using original
parts.
6. Altering the circuitry without prior consent or advice is not legitimate.
7.Any work security regulations that are applicable at the location where the appliance is being serviced have to be strictly obeyed. This applies
also to any regulations about the work place itself.
8.All instructions concerning the handling of MOS - circuits have to be observed.
Note: SAFET
Y
COMPONENT
(
HAS T
O
B
E
REPLACED WIT
H
ORIGINAL P
A
R
T ON
L
Y
)
1ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual

T
abl
e
o
f
Contents
Im
p
o
r
tant Safet
y
Instructions ....................................................................................................... 1
ZxA5 Series Owne
r
’s Manual....................................................................................................... 2
Safet
y
First ................................................................................................................................... 3
Descri
p
tion ................................................................................................................................... 4
S
y
stem Features - ZxA5............................................................................................................... 4
S
y
stem Covera
g
e - ZxA5 ............................................................................................................. 4
S
y
stem Setu
p
- ZxA5 ................................................................................................................... 5
ZxA5 Am
p
lifie
r
.............................................................................................................................. 5
Sus
p
endin
g
ZxA5 S
p
eake
r
S
y
stems............................................................................................ 7
ZxA5 Sta
g
e Monito
r
Positions .................................................................................................... 13
S
p
ecifications ............................................................................................................................. 14
Dimensions ................................................................................................................................ 15
Bloc
k
Dia
g
ram............................................................................................................................15
Fre
q
uenc
y
Res
p
onse, Beamwidth, and Directivit
y
..................................................................... 16
ZxA5 Ri
gg
in
g
Accessor
y
Reference Table ................................................................................. 17
Paintin
g
ZxA5 S
p
eaker S
y
stems............................................................................................... 18
ZxA5 Series Owne
r
’s Manual
Than
k
y
ou fo
r
choosin
g
the Electro-Voice®ZxA5 series louds
p
eake
r
s
y
stem. This s
y
stem is the
culmination of EV’s 75
y
ears of ex
p
erience in transduce
r
desi
g
n. Please take time to consult this
manual so that
y
ou can understand all the features built into
y
ou
r
EV s
y
stem and full
y
utilize all its
p
erformance ca
p
abilities.
ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual 2

Safet
y
First
When setting up, installing and using the Electro-Voice®ZxA5 speaker system, there are a
number of precautions that you should follow:
·When Electro-Voice®ZxA5 speakers are used for portable applications in which they will be
positioned directly on the floor, make sure that the floor or stage is solid and secure.
·Electro-Voice®ZxA5 speakers include 1-3/8 inch stand mounts to allow mounting on tripod
stands.
Make sure to:
·Check the specifications of the speaker stand to be certain it is capable of supporting the weight
of the speaker.
·Check that the speaker stand is placed on a flat, stable surface and be sure to fully extend the
legs of the stand. Do not try to make the stand “taller” and compromise its structural integrity.
·Route cables and position the stand so that performers, production crew and audience members
will not trip over the stand or cables and pull the speaker system over. Secure cables with wire
ties or tape whenever possible.
·Do not attempt to suspend more than one speaker on a stand designed for a single speaker
·Unless you are confident that you can safely handle lifting the weight of the speaker onto the
stand, ask another person to help you place it.
·If you intend to hang or fly the ZxA5 system, only do so safely with the correct hardware and
accessories.
WARNING:
Suspending any object is potentially dangerous and should only be
attempted by individuals who have a thorough knowledge of the techniques and
regulations of rigging objects overhead. Electro-Voice
®
strongly recommends that ZxA5
speakers be suspended taking into account all current national, federal, state and local
regulations. It is the responsibility of the installer to ensure that ZxA5 speakers are safely
installed in accordance with all such regulations. If ZxA5 speakers are suspended,
Electro-Voice
®
strongly recommends that the system be inspected at least once a year.
If any sign of weakness or damage is detected, remedial action should be taken
immediately.
There are data sheets for each EV Suspension and Array Kit that should
also be consulted prior to suspending speakers.
·Electro-Voice®does not recommend use of ZxA5 speakers outdoors without
protection from rain or in high moisture environments.
·Electro-Voice®ZxA5 loudspeakers are easily capable of generating sound pressure
levels sufficient to cause permanent hearing damage to anyone within normal
coverage distance. Caution should be taken to avoid prolonged exposure to sound
pressure levels exceeding 90 dB.
3ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual
This is a Class A product. In a domestic environment this product my cause radio interferences in which case
the user may be required to take adequate measures.

Descri
p
tion
The Electro-Voice®ZxA5 high powered loudspeakers are fully integrated audio systems with
carefully matched electronics and transducers. These products make it easy to setup a high
quality sound system quickly with a minimum amount of cables and external electronics. You won’t
find a speaker system available on the market that offers the unbelievable sound, incredible
flexibility and tremendous output capability of the ZxA5 anywhere near it’s size and weight.
System Features - ZxA5
·Integrated Amplifie
r
with 1000W LF, 250W HF
·Selectable 100 Hz High Pass
·XLR and 1/4” TRS Input Connector
·XLR Output Connector
·PowerCon Connector with Slave Through
·DVX3150 15” LF Transducer with Forced Air Cooling
·ND2 2” Voice Coil, 1” Exit Neodymium Compression Driver
· Two Models: 60° x 60° or 90° x 50° Coverage Patterns
·High Sensitivity, 133 dB Maximum SPL
· Adjustable Monitor Angle (45° or 55°)
·3 Anchor Plates for Single Stud Fitings and 10 Integral Suspension Points
·Full Line of Accessories
S
y
stem Covera
g
e - ZxA5
Cove
r
age Patterns and
A
pplications
ZxA5-60 60° x 60° coverage for long-throw and cluster applications
ZxA5-90 90°
x
50° for wide
r
covera
g
eo
r
shorte
r
distances
Figure 1a:
3D EASE Directivity Balloon,
ZxA5-60, 60° x 60° Coverage
Figure 1b:
3D EASE Directivity Balloon,
ZxA5-90, 90° x 50° Coverage
ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual 4

S
y
stem Setu
p
- ZxA5
To get the ZxA5 into operation as quickly as possible, please observe the following steps and
precautions:
·Plug the 3-terminal PowerCon AC cable into a grounded line receptacle. Extension cords can be
used to lengthen the AC cable as necessary but make sure that they are 3-conductor 14 gauge or
greater, and that they are properly grounded to avoid electrical hazards and extraneous noise.
·Be sure that the ZxA5 is plugged into an AC power source that is capable of supplying the correct
voltage. If the line voltage drops too much, the built-in amplifiers won’t be able to develop their
rated power and sound quality will suffer. Under high signal conditions, the 120V ZxA5 amplifier
can draw 3 - 4 amps of current (2 amps at 240V). That means that no more than
(3) ZxA5 systems should be plugged into a single 15 amp electrical service. Be cautious of what
else is plugged into the same electrical service line to avoid electrical problems and poor
performance.
CAUTION: Before turning the power on, make sure that the level controls are down to
avoid t
r
ansients o
r
unex
p
ected loud sound.
ZxA5 Am
p
lifie
r
Input Signal Connector
Electronically balanced inputs
for the connection of high-
level signal sources such as
mixers, signal
processors, etc. Establishing
the connection is possible via
a combinaton 1/4” TRS and
XLR jack. Balanced
connection is recommended
to prevent noise or HF-
interference.
CAUTION: Before connecting or
disconnecting any plugs, make sure to set
the level control to its counterclockwise
stop, which prevents the system and
audience from contact pops and noise.
Output Signal Connector
Output is full bandwidth pass
through. Figure 2:
A
m
p
lifier Panel, ZxA5
5ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual

ZxA5 Am
p
lifie
r
(
cont’
)
C
r
ossove
r
Mode Switch
Selects between 40 Hz highpass filter for Fullrange
use, and 100 Hz highpass filter for use with a
subwoofer. It is not recommended that you use a
ZxA5 in Fullrange mode with subwoofers.
Level
This control sets the output level of the ZxA5 in a
range between -
∞ dB and +6dB. The internal power
amplifier provides a nominal input sensitivity of
+6dBu.
Power Switch
A
C switch for switching the ZxA5’s power ON or
OFF. The switch lights after turning the power ON.
If the switch is not lit upon turning the power on,
make sure that the AC cord is correctly connected.
If the AC cord is correctly connected and the AC
switch does not light upon power-on, please
contact your local dealer.
Mains In
A
C connection is established via a PowerCon
connector. A 15’ (5m) long AC cord with PowerCon
plug is supplied.
Mains Out
The PowerCon AC out socket allows the
connection of additional ZxA5 Systems.
To prevent AC network overload, connecting more
than (3) ZxA5 Systems to a single AC outlet (10A -
16A
)
is not recommended.
CAUTION: This appliance has no user-serviceable parts inside. Leave any servicing
and maintenance to
q
ualified se
r
vice technicians onl
y
.
ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual 6
CAUTION: Blue and grey PowerCon power connector shall not be engaged or
disengaged when under load or live.

Sus
p
endin
g
ZxA5 S
p
eake
r
S
y
stems
ZxA5 enclosures have 5 steel anchor points internally mounted on the top, bottom, and rear.
Single stud fittings can be attached to these anchor plates and used as suspension points. Each
of these anchor plates also has a M8 thread to accept rated forged M8 shoulder eyebolts. In
addition to these points there are five additional M8 threaded points; two on the handle side, and
three on the rear. These points can be used for suspending ZxA5s vertically, horizontally,
individually, in clusters, or to attach to EV mounting brackets. Working load limits for the ZxA5 and
fittings are shown in Figure 3.
Figure 3:
Workin
g
Load
-
Limit Ratin
g
of ZxA5 S
p
eaker S
y
stem
Prior to each use, inspect the grid assembly or suspension point(s) and associated hardware for
any cracks, deformations, broken welds, corrosion, missing or damaged components which could
reduce the grid assembly or suspension point(s) strength. Replace any damaged hardware. Never
exceed the limitations or maximum recommended load intended for grid assembly design or
suspension point(s). As an added safety measure, it is suggested that the user install a second
suspension point back to the grid (or building structural supports). This redundant safety point
should have as little slack as possible (less than one inch is preferable).
Prior to each use, inspect the loudspeaker enclosures for any cracks, deformations, missing or
damaged components, which could reduce enclosure strength. Inspect the bracket assembly on
the enclosures for any cracks, deformations, missing or loose screws which could reduce the
flying hardware strength. Replace any loudspeaker systems that are damaged or missing
hardware. Never exceed the limitations or maximum recommended load for the ZxA5 systems.
7ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual

Sus
p
endin
g
ZxA5 S
p
eake
r
S
y
stems
(
cont’
)
ZxA5 M8 Suspension Points
Metric (M8) inserts are equipped on the top and bottom of the enclosure, around the handle, and
on the back of the enclosure for a total of 10 points. The inserts can be used to attach forged
eyebolts or rigging brackets.
(2) M8 Suspension Points
(Single-Stud Anchor Plate
Remo
v
al Re
q
uired
)
(2) M8 Suspension Points
(
Decal Remo
v
al Required
)
(2) M8 Suspension Points
(
Decal Remo
v
al Re
q
uired
)
(2) M8 Suspension Points
(Removal of Handle Bolts
Required
)
(2) M8 Suspension Points
(Single-Stud Anchor Plate/
Decal Removal Required)
Figure 4a:
ZxA5 M8 Sus
p
ension Point
s
(
To
p
, Handle, Rear
)
Figure 4b:
ZxA5 M8 Sus
p
ension Point
s
(
Bottom
)
ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual 8

Sus
p
endin
g
ZxA5 S
p
eake
r
S
y
stems
(
cont’
)
Suspending the ZxA5 using optional Elect
r
o-
V
oice Single-Stud Rigging Kits
The ZxA5 is shipped with three single-stud anchor plates for rigging with single-stud rigging. There
are two more locations on the bottom to mount single-stud anchor plates for flying the ZxA5
upside-down orhorizontally.Alloftheselocations
can facilitate M8 Eyebolts if desired as well.
Figure 5:
Suspending the ZxA5 Using Included Single-Stud
Anchor Plates
Kit Used (Left View) -
SSK-1 Single-Stud Rigging Kit
(
x1
)
Kits Used (Right View) -
SSK-1 Single-Stud Rigging Kit
(
x2
)
EBK-3 Forged M8 Eyebolt Kit (x1)*
*EB
K
-3 on Bottom of
T
op
Enclosure
(
not shown, see Fi
g
ure 3b
)
Ste
p
1: Remove Decals Step 2: Attach Single-Stud Anchor Plates
Removed from the Top of the Enclosure or
optional RK-Z Kit (shown) or Eyebolts (not
shown)
Figure 6:
Suspending the ZxA5 Upside-Down Using
Included Single-Stud Anchor Plates and Single-
Stud Rigging Kit
Kits Used
-
RK-Z Single-Stud Anchor Plate Kit
(
x1
)
SSK-1 Single-Stud Rigging Kit (x1)
9ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual

Sus
p
endin
g
ZxA5 S
p
eake
r
S
y
stems
(
cont’
)
Horizontal Suspension of the ZxA5
The ZxA5 is capable of being suspended horizontally from the side (handle) or downward from the
rear with the use of M8 Eyebolts.
Figure 7:
Suspending the ZxA5 Downward from Rear Using
Optional Forged Eyebolt Kit*
Kit Used
-
EB
K
-
3 For
g
ed M
8
E
y
ebolt Kit
(
x1
)
*Note - When suspending from the rear M8 suspension
points, it is recommended that the (2) left M8 suspension
points are used on the rear of the enclosure for best weight
distribution in relation to enclosure’s center of gravity.
Figure 8:
A
ssembling Eyebolts to Handle
for Horizontal Suspension
Step 1: Remove Handle Bolts Step 2:
A
ttach E
y
ebolts
Figure 9:
Suspending the ZxA5 Horizontally from Handle
Using Optional Forged Eyebolt Kit
Kit Used
-
EB
K
-
3 For
g
ed M
8
E
y
ebolt Kit
(
x1
)
ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual 10

Sus
p
endin
g
ZxA5 S
p
eake
r
S
y
stems
(
cont’
)
H
A
-5 Handle Mount
V
S
A
-1 Stron
g
-
A
rm
Step 1: Remove Handle Bolts
and Handle Ste
p
2:
A
ttach H
A
-5 and Handle Bolts Ste
p
3:
A
ttach
V
S
A
-1 Stron
g
-
A
rm Mount
Figure 10:
A
ssembling HA-5Adapter for use with VSA-1 Strong-Arm Mount
Kits Used -
HA-5 Handle Adapter Kit (x1)
VSA-1 Strong-Arm Mount (x1)
Arraying and Suspending the ZxA5 using optional Elect
r
o-
V
oice Mounting o
r
Ar
r
ay
Brackets
Figures 11 and 12 show several applications using EV mounting and array brackets. Carefully
follow the instructions in this manual & the user manual packaged with EV brackets, and always
use safe rigging practices when suspending ZxA5.
Spigot to
A
ttach to Beam or
T
russ Clam
p
Figure
1
1:
Suspending the ZxA5 Vertically from Handle Using Optional
Handle Adapter and Strong-Arm Mount
Kits Used -
HA-5 Handle Adapter Kit (x1)
VSA-1 Strong-Arm Mount (x1)
*Note - Please consult VSA-1 User Manual for additional
information.
11 ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual

Sus
p
endin
g
ZxA5 S
p
eake
r
S
y
stems
(
cont’
)
Kit Used - MB5
W
all/Ceilin
g
Mountin
g
Bracket
(
W
all Confi
g
uration
)
Kit Used - MB5
W
all/Ceilin
g
Mountin
g
Bracket
(
Ceilin
g
Confi
g
uration
)
Kits Used - CB5 Ar
r
a
y
Bracket Kit
(
x1
)
*
SSK-1 Sin
g
le-Stud Ri
g
g
in
g
Kit
(
x1
)
Kit Used - CB5
A
r
r
a
y
Bracket Kit
(
x2
)
*
NOTE: Do not
exceed working
load limit for
individual rigging
points when
arraying the
ZxA5. (See
Figure 3,
Page 7)
Kits Used - CB5 Ar
r
a
y
Bracket Kit
(
x2
)
*
SSK-1 Single-Stud Rigging Kit (x2)
EBK-3 Fo
r
g
ed M8 E
y
ebolt Kit
(
x1
)
Kits Used - CB5
A
r
r
a
y
Bra
c
ket Kit
(
x4
)
*
EBK-3 Fo
r
g
ed M8 E
y
ebolt Kit
(
x1
)
*Note - CB5 Ar
r
a
y
Kits can be used
f
or 60° or 90° Spla
y
A
n
g
les
Figure 12:
A
rra
y
in
g
and Sus
p
endin
g
the ZxA5
ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual 12

ZxA5 Sta
g
e Monito
r
Positions
ZxA5 as a Monitor
By design the ZxA5 is a perfect solution for stage monitors. As different stage sizes require
different monitor angles, the ZxA5 offers two angles without any additional accessories.
Step 1: Remove Monitor Foot
Screws Step 2: Rotate Monitor Feet 180° Step 3: Re-attach Monitor Feet
and Screws
Figure 13:
Switchin
g
the Monitor Feet from the 45° to 55° Positions
Figure 14a:
ZxA5 a
s
Monitor in 45° Position Figure 14b:
ZxA5 as Monitor in 55° Position
CAUTION: When flipped to 55° the feet protrude from the enclosure. Care should be
taken when moving the enclosure, since damage to the feet or enclosure might occur if
the system is dropped or slid across a rough surface. It is recommended that the feet be
returned to the 45° position for transport.
13 ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual

Freq. Response1(-3 dB): 58Hz – 18kHz
Freq. Range1(-10dB): 50Hz – 20kHz
Max Calculated SPL: 133 dB
Horizontal Coverage: 90° or 60°
Vertical Coverage: 50° or 60°
LF Amplifier Power: 1000W RMS
HF Amplifier Power: 250W RMS
LF Transducer: DVX3150, 15in (300mm) Driver
HF Transducer: ND2-16, 1in. (25.4mm) exit Neodymium
Compression Driver
Crossover Frequency: 1.5 kHz
Input Connector: XLR and 1/4” TRS Combination
Output Connector: XLR
Power Requirement: 120 VAC, 50-60 Hz, or
230 VAC, 50-60 Hz
Enclosure Material: Polypropylene Structural Foam
Suspension:
Enclosure has locations for 5 Single-
Stud Attatchment Plates and 10 Forged
Steel Eyebolts – 2 on Top, 2 on Bottom,
2 on Side, and 4 on Rear of Enclosure
Grille: Polyester Powder Coated, 16GA
Galvanized Steel
Dim (H x W x D): 27.26” x 17.57” x 16.16”
(692mm x 446mm x 411mm)
Net Weight: 50.5 Ibs (22.9 kg)
Shipping Weight: 58.9 Ibs (26.7 kg)
1Half Space measurement
T
echnical S
p
ecifications
ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual 14

Dimensions
T
o
p
V
iew
Left
V
iew Front
V
iew Ri
g
ht
V
i
e
w Rear
V
iew
Block Dia
g
ram Bottom
V
i
e
w
MAINS-L
POWER
MAINS
120V AC
230V AC
50 Hz
–
60 Hz
MAINS-E
MAINS-N
T10
A
@ 12 0V
T6.3A
@ 230V POWER SUPPLY
TURN ON DEL
A
Y
MOUT-L
MOUT-E
MOU
T
-N
THERMAL
PROTECTION
LIMITER HI
A
MP
HF
PROTECTION
INPUT
HPF
FULLRANGE
LEVEL
HPF and PEQ
Class D
A
m
p
Module
LF
40Hz,
24dB, LR
1.5kHz, 24dB, LR LIMITER
LO AMP
HPF
LPF and PEQ PROTECTION
OUTPUT
100Hz, 24dB, LR MID/HIGH
1.5kHz, 24dB, LR THERMAL
PROTECTION
15 ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual

Fre
q
uenc
y
Res
p
onse, Beamwidth and Directivit
y
ZxA
5
-60, 60° x 60° Covera
g
e ZxA
5
-90, 90° x 50° Covera
g
e
Fre
q
uenc
y
Res
p
onse: Fre
q
uenc
y
Res
p
onse:
110
Full Range, Full Space
Hi
g
h Pass, Full S
p
ace
110
Full Range, Full Space
Hi
g
h Pass, Full S
p
ace
100 100
90
90
80
80
70
20 50 100 1000 10000 20000
Fre que ncy(Hz)
7020 50 100 1000
10000 20000
Fre que ncy(Hz)
Beamwidth:
Beamwidth:
Directivit
y
:
Directivit
y
:
ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual 16

Model Description Part No.
CB5-B Array Bracket Kit, Black Finish 301625-001
CB5-W Array Bracket Kit, White Finish 301625-002
MB5-B Wall/Ceiling Mounting Bracket Kit, Black Finish 301626-001
MB5-W Wall/Ceiling Mounting Bracket Kit, White Finish 301626-002
SSK-1 Single-Stud Rigging Kit (Set of 3) 301633-000
EBK-3 Forged M8 Eyebolt Kit (Set of 3) 301634-000
RK-Z Single-Stud Anchor Plate Kit (Set of 3) 301812-000
TMK-ZX Truss Mount Kit, Includes VSA-1, TCA-1, and
HA-5 (Black) KIT000007-001
HDC-5 Heavy-Duty Stackable Cover, Black 301813-001
HA-5 Handle adaptor for use with VSA-1 301811-001
VSA-1 Vertical Strong Arm ACC000007-001
TCA-1 Trussclamp adaptor for VSA-1 ACC000012-001
ZxA5 Ri
g
g
in
g
Accesso
r
y
Re
f
erence
T
able
17 ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual
FCC Information
FCC INFORMATION (USA)
1. IMPORTANT: Do not modify this unit! Changes or modifications not expressly approved by
the manufacturer could void the user’s authority, granted by the FCC, to operate the
equipment.
2. NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Paintin
g
ZxA5 S
p
eake
r
S
y
stems
Painting a ZxA5 Enclosure
The ZxA5 Loudspeaker Enclosures are made of a high performance Polypropylene material. For
best paint adhesion, we recommend a “Plastic Adhesion Promoter” be applied before any paint.
Sherwin Williams Plastic Adhesion Promoter UP07226 is a good example (See Telex document
number LIT000066-000 for further details.) Once Plastic Adhesion Promoter is applied follow the
manufacturer’s painting directions as you would normally.
Painting a ZxA5 Grille
Remove grille from loudspeaker and remove the backing material & logo from grille prior to painting.
Once the paint is dry, reapply the backing material and logo to the grille. Spray adhesive such as
3M Super 77 may help adhere the backing material to the grille.
Additional Precautions to be
T
aken
Prior to painting, be sure to take precautions not to get paint into the transducers. This can be
done by masking the grille, temporarily removing the grille and masking the transducers, or by
temporarily removing the grille and temporarily removing the transducers. Precautions must also
be taken not to get paint into any exposed electrical components by masking them off prior to
painting. It is also recommended that any exposed rigging points, warning labels, or instruction
labels be masked off for ease of future operation.
Ri
gg
in
g
P
oints Masked
Grille Masked
ZxA5 Enclosure
WARNING: It is critical to the system’s operation
that all transducers and exposed electrical
components be masked off prior to painting.
Painting
V
iew:
Paintin
g
the ZxA5 Enclosure
ELECTRO-VOICE
®
ZxA5 Owne
r
’
s Manual 18