ELECTROCOMPANIET EC 4.8 MKII User manual

EC 4.8 MKII
Balanced Reference Preamplifier
Owner's Manual
EN
ENGLISH

2
Welcome to the world of Electrocompaniet!
We thank you for choosing an Electrocompaniet high-end product.
At Electrocompaniet we are relentlessly focused on developing
audio equipment that is capable of bringing the fabulous
experience of the concert hall into the very heart of your home.
Our aim when developing and testing new products is to ensure
that the wonderful richness of tone and every nuance of feeling
and emotion of a piece of music is delivered to you just as the
artist intended.
We continually strive to give you the very best musical listening
experience available whatever your preferred musical genre.
Sincerely yours,
The Electrocompaniet team

3
Unpacking the EC 4.8 MKII
Immediately upon receipt of the EC 4.8 MKII, inspect the carton for possible damage
during shipment. The carton and packaging have been designed to provide the safest
possible protection for transport of your preamplifier. Unpack the unit carefully.
Save all packaging materials for future shipment.
The contents of the carton
• 1 pc. Electrocompaniet EC 4.8 MKII Reference Preamplifier
• 1 pc. AC main cord
• 1 pc. Inspection card
• 1 pc. Owner's manual
• 1 pc. IR Remote control
• 2 pcs. AAA Batteries
Set up procedure
Before connecting the EC 4.8 MKII to the AC Power outlet, check that the main volt-
age indicated on the rear panel corresponds to the line voltage in the country were
you intend to use the unit.
How to avoid damages
Do not under any circumstances connect or disconnect equipment when power is
turned on. The design of the RCA plug generates a huge transient when inserted.
Connecting or disconnecting equipment with the power on can result in severe
damage to both speakers and amplifier.
How to avoid noise problems
The EC 4.8 MKII contains delicate circuits that are sensitive to magnetic stray fields.
The unit should not be placed near power voltage transformers, TV sets etc. Care
should also be taken regarding placement of the interconnect cables. Do not run
interconnect cables in parallel with main cords or speaker cables. Keep interconnect
cables as short as possible.
How to avoid possible antenna problems
In some setups hum may occur when you connect the radio, VCR or TV to your system.
The problem is caused by DC voltage offset coming from your antenna system. Please
contact your cable network operator.

4
How to connect your system
Please read this page carefully and use rear panel illustrtation at page 5 as reference.
INPUTS
Single-ended RCA input and operation
There are three sets of single ended inputs labeled AN3, AN4 and HT/AN5.
All inputs are similar regarding sonic performance. HT/home theater mode (Volume
control does not affect the signal). AN5 - normal input operation mode affected by the
volume control.
Unused inputs may be shorted to ground, using a RCA shorting plug.
Balanced operation
There are two sets of balanced inputs labeled AN1 and AN2. Connect the right chan-
nel input to the inputs on the right side of the EC 4.8 MKII and the left channel inputs
on the left side of the EC 4.8 MKII.
OUTPUTS
REC OUT
Rec outputs are used for recording. The source you listen to will be monitored through
this output. The volume control setting does not influence the record output.
BALANCED OUTPUT
The balanced output is a variable output, dependent on the volume control setting and
MUTE function. These outputs control the power amplifier(s).
SPAC
These contacts are used to communicate with power amplifiers AW 2x120 and AW
3x120. Connect a SPAC Com cable (sold separately) from SPAC A to one of the
amplifier and SPAC B to the other. When these cables are connected to the
amplifiers the EC 4.8 MKII will monitor the vital functions on the amplifiers.
SPAC Multi is reserved for future use.
Never use shorting plugs in outputs.
How to power up your system
You should always power up your system in the following way: Signal sources
(CD player, streamer, etc.) first, then the EC 4.8 MKII. Allow a 30 seconds warm-up
before you turn on the amplifier.
When switching off your system
In daily operation, put the EC 4.8 MKII in standby mode by holding the Mute button
on the remote control for1-2 sec. To turn it completely off, press the power button on
the front panel. When turning off your whole system, start with the amplifier, then the
EC 4.8 MKII and then the signal sources.

5
1. Balanced analog right output 2. Balanced analog AN1 right input 3. Balanced analog AN2 right input 4. Single-ended analog AN3 right input 5. Single-ended analog AN4 right input 6. Single-ended analog REC right output 7. Single-ended analog HT/AN5 right input 8. Balanced analog left output 9. Balanced analog AN1 left input
EC 4.8 MKII Rear panel illustration
1 2 3 4 5 6 78 9 10 111213 14 15 16 17 18
10. Balanced analog AN2 left input 11. Single-ended analog AN3 left input 12. Single-ended analog AN4 left input 13. Single-ended analog REC left output 14. Single-ended analog HT/AN5 left input 15. USB for Remote charge 16. Mini USB for software upgrade 17. SPAC connection 18. Mains power input

6
5
3
1
4
2
Front panel overview
The main switch is located in the centre of the lower part of the front panel ( 5 ).
The four buttons on the right-hand side of the front panel is used to adjust the volume
and select the input source. Use the up and down buttons to adjust the volume, and
the left and right buttons to select input source
Navigator
Button Function Description
1 Volume Up Increases the volume level
2 Volume Down Decreases the volume level
3 Select source left Selects the next source to the left
4 Select source right Selects the next source to the right
5 Power switch Turns the preamplifier on and off
Input sources
Audio
Source Display Text Description
Analog 1 AN1
Balanced source connected to AN1 input
Analog 2 AN2
Balanced source connected to AN2 input
Analog 3 AN3
Single-ended source connected to AN3 input
Analog 4 AN4
Single-ended source connected to AN4 input
HT/AUX HT/AN5
Single-ended source connected to HT/AUX input

7
Using the remote control
When using the remote control, the front end of the remote control should be pointed to
the front panel of your EC 4.8 MKII. A free line of sight is required between the remote
control and the infrared sensor on the front panel.
Remote control overview
1. Mute - on/off.
Standby mode - hold mute1-2 sec. to set
the preamplifier into standby mode.
2. AN 2 - switch to Analog 2 input.
3. AN 4 - switch to Analog 4 input.
4. VCR - Dimming the display.
5. AN 5 - switch to Analog 5 input.
6. AN 1 - switch to Analog 1 input.
7. AN 3 - switch to Analog 3 input.
8. Volume UP.
9. Volume DOWN.
10.SACD - switch to Analog 1 input.
11. HT - switch to a Home theater input.
Replacing batteries
Use 2pcs AAA or LR03 batteries.
Observe correct polarization when
inserting batteries. Please remove
batteries when the remote is not used
for a prolonged period of time.
IR Remote control codes
( page 8)
AN 2 AN 4 AN 3 AN 1
AN 5
VCR
1
2
3
4
5
6
7
8
9
11
10

8
IR Remote control codes
RC5 codes are denoted as xx.yy where xx is 5 bit adress and yy is 6 bit command/
data. All numbers are in decimal.
Key label Code Type Code Hex
MUTE/STANDBY RC5 16.13
CD / AN2 RC5 16.20
TUN / AN4 RC5 16.21
VCR - DIM RC5 16.61
AUX / AN5 RC5 16.60
DVD / AN1 RC5 16.57
TAPE / AN3 RC5 16.56
VOLUME UP RC5 16.16
VOLUME DOWN RC5 16.17
SACD / AN1 RC5 16.59
HT RC5 16.58

9
Technical specifications EC 4.8 MKII:
INPUT CONFIGURATIONS
XLR input: 1 = ground 2 = positive 3 = negative
RCA: Shield = ground Center = positive
RCA to XLR adapter: Shield = ground Center = positive
OUTPUT CONFIGURATIONS
XLR output: 1 = ground 2 = positive 3 = negative
Never use shorting plugs in outputs.
The following technical data were measured on randomized test objects and are typical
data. All measurements are made at 120V / 240V // 50Hz / 60Hz
MEASUREMENTS SINGLE ENDED BALANCED
Input impedance 47 kOhm 47 kOhm
Output impedance 100 Ohm 100 Ohm
Maximum gain 6 dB 6 dB
Minimum gain - 111 dB - 111 dB
Noise floor (0 dB gain) < -130 dB < -130 dB
THD (1V in, 1V out) -120 dB -130 dB
Max input +- 15Vp-p +- 30Vp-p
Max output +- 30Vp-p +- 30Vp-p
Frequency response 1 – 200 kHz 1 – 200 kHz
Channel separation > 120 dB > 120 dB
Power consumption (no load or signal): 30 W
The EC 4.8 MKII is DC coupled from input to output.
WEIGHT & DIMENSIONS:
Weight: 11.3 kg – 24.9 lbs
Width:470 mm – 18.5 inches
Depth: 372 mm – 14.64 inches
Height: 80 mm – 3.14 inches
*Specifications are subject to change without further notice

10
IF SERVICE IS NEEDED
Your dealer will have all relevant information regarding the service centers in your area,
and will ensure that your unit is serviced with minimum delay. It is our general policy to
have your unit returned to you within five working days. This is an average time and can
vary locally, depending on the workload at that particular service station. If, for some
reason there are no service facilities available in your country, contact Electrocompaniet support
first. If requested to do so by technical personell, please ship the unit to the following address:
EC Living AS,
Breivikveien 7,
N-4120 Tau,
Norway
Web: www.electrocompaniet.com
Service department: support.electrocompaniet.com
The end user is responsible for all shipping charges, insurance, re-import and dutycharges.
When shipping a product to the factory for service, always include the following:
1. A sales slip or other proof of purchase if repair is claimed under warranty.
2. A proforma invoice with value of goods, stating that the EC 4.8 MKII is returned to Norway
for repair.
3. An accompanying letter describing faults, symptoms, or problems with the unit.
4. Always ship the unit in its original carton and packaging material to prevent damage in
transit.
Electrocompaniet will not cover damages incurred in transit. If you require further information
concerning the operation of the unit, or if you have any questions related to service, please do
not hesitate to contact your dealer or your national distributor.
User Manual Updates Online
An updated version of the User Manual may be available online at the Electrocompaniet
web site. Occasional updates are needed to reflect new features added to the player since
the user Manual was printed. As future firmware updates bring in new features and func-
tions, the online version of the user Manual will be updated accordingly.

11

Warning!
To avoid risk of fire or electric shock, do not expose this appliance to rain or moisture.
Verify line voltage before use. Do not remove cover. No user serviceable parts inside.
Refer servicing to qualified service personal. The warranty is void if the product is tampered
by non-authorised personnel.Use only authorized Electrocompaniet service center.
LOCAL DEALER
DEALER
STICKER
HERE
REV 1.0 2019
Designed and manufactured in Norway
www.electrocompaniet.com