Electrolux EQBM100AS User manual

user manual
Electrolux En:V barbecue
EQBM100AS
side burner
EQMW40AS

electrolux en:v barbecue contents i
environmental tip
Information on disposal for users
• Most of the packing materials are recyclable. Please
dispose of those materials through your local recycling
depot or by placing them in appropriate collection
containers.
• If you wish to discard this product, please contact your
local authorities and ask for the correct method of disposal.
Congratulations
Congratulations and thank you for choosing our Electrolux
En:V barbecue. We are sure you will nd your new
barbecue a pleasure to use. Before you use the barbecue,
we recommend that you read through the entire user
manual, which provides the description of the barbecue and
its functions.
To avoid the risks that are always present when you use
a gas appliance, it is important that it is installed correctly
and that you read the safety instructions carefully to avoid
misuse and hazards.
We recommend that you keep this instruction booklet for
future reference and pass it on to any future owners.
After unpacking the barbecue please check it is not
damaged. If in doubt, do not use the appliance but contact
your local Electrolux Customer Care Centre.
Contents
• Electrolux En:V barbecue product description ii
• Side burner product description iii
• Dimensions iii
• Parts 1
• Important safety instructions 2
• Assembling the barbecue 3
• Mounting optional side burner 4
• Gas specications 5
• Gas bottle safety information 6
• Installing the gas cylinder 6
• Leak test procedure (Universal LPG) 7
• Conversion to Natural Gas 7
• Leak test procedure (Natural Gas) 8
• Choosing a location 9
• Installation warnings 10
• Activating the wheel brake 10
• Options for conguration of hotplates and grills 11
• Operating instructions 11
• Using the side table 12
• Using the warmer drawer 12
• Using the roasting hood 13
• The waste bin 13
• Side burner operation 13
• Cleaning and care 14
• Maintenance 15
• Troubleshooting 15
• Warranty 16

ii product description electrolux en:v barbecue
Electrolux En:V barbecue
1 Retractable roasting hood
2 Battery cover
3Burner controls
4 Mounting screws for side burner (not visible)
5 Temperature indicator
6 Wheel brakes
7 Wheels
3
4
1
9
12
9
8
2
5
11
10
15
14
13
6
7
8 Warming racks
9 Fold down side table
10 Grill assembly
11 Hotplate
12 Warmer drawer
13 Gas connection point (under drawer, not visible)
14 Slide-out gas bottle tray
15 Slide-out waste bin

electrolux en:v barbecue product description iii
Optional side burner
Dimensions
1 Side burner weatherproof lid
2 Reversible trivet
3 Burner crown
4 Burner control
Side burner tted to barbecue
1
2
3
4
603mm
1191mm
1582mm
942mm
30mm
135mm
1184mm 395mm 596mm
900mm 204mm
582mm
525mm
440mm 51mm
1141mm
125mm
Weight without side burner 116kg
Weight with side burner 125kg

electrolux en:v barbecue parts 1
Optional side burner partsElectrolux En:V barbecue parts
description qty
Electrolux
En:V
barbecue
1
Flame tamers 2
Solid hot plate 1
Grill
assemblies
2
Warming
racks
2
1 plastic bag containing this instruction book
description qty
Lid 1
Trivet 1
Burner
components
1 set
Mounting
brackets
2
Burner box
assembly
1
1 Plastic bag containing this instruction book, 8 M6
screws, 1 1.8mm NG injector, 1 small screw driver
Tools you will need for assembly:
– Spanner for gas inlet connection
– Phillips head screwdriver
Contents of your barbecue pack: Contents of your optional side burner pack:

2 important safety instructions electrolux en:v barbecue
Please read the user manual carefully and store in a handy
place for later reference.
Meanings of the symbols used in this manual are shown
below:
warning
This symbol indicates information concerning your
personal safety
caution
This symbol indicates information on how to avoid
damaging the appliance
tips and information
This symbol indicates tips and information about use
of the appliance
environmental tip
This symbol indicates tips and information about
economical and ecological use of the appliance
This symbol indicates never to do this
For your safety please read this book before
operating your barbecue.
warning
Improper installation, adjustment, alteration or
maintenance can cause injury or property damage.
Please contact your nearest Electrolux Service
Department for additional information or assistance
for an approved installer.
NOTE TO THE INSTALLER
THIS MANUAL MUST REMAIN WITH THE OWNER FOR
FUTURE REFERENCE
Important safety instructions
warning
IF YOU SMELL GAS, do not attempt to light the
barbecue. Locate the leak and re-tighten the leaking
joint. Carry out the Leak Test procedure as described in
this manual. If the leak persists, turn off the gas supply
and call Electrolux Service or a Licensed Gas Fitter.
warning
Do not lean over barbecue when lighting.
Do not leave the barbecue unattended when alight.
Do not delay lighting once the gas has been turned
on.
Do not store or use aerosol cans in the vicinity of the
barbecue.
Do not store flammable liquids in the vicinity of the
barbecue.
Do not use caustic or abrasive based cleaners on the
barbecue.
Do not operate the barbecue with the cover on.
Do not attempt to dismantle or adjust the control
valves.
Do not attempt to dismantle or adjust the regulator.
Do not test for leaks with a naked flame.
Do not modify the construction of this appliance or
modify the injector orifice size.
Do not obstruct any ventilation of the barbecue.
Do not allow children to operate or play near the
barbecue.
caution
This barbecue is supplied set up for Universal LPG
and is labelled accordingly. A Natural Gas conversion
kit is available for purchase from Electrolux Service
or Spare Parts. Conversion of this unit to Natural Gas
must be carried out by a qualified licensed person
and a Certificate of Compliance must be issued
to the owner on completion of the installation and
conversion.

electrolux en:v barbecue assembling the barbecue 3
1. Remove packaging & remove all components from inside
cabinet.
2. Unfasten bolts securing unit to the pallet base and
remove unit from base.
3. Position flame tamers into desired locations (under
where grill sections will be fitted) and fix back edge of
the flame tamer into rear of barbecue body.
Assembling the barbecue
4. Place hotplate and grill sections into desired positions
ensuring that the flame tamers are under grill sections
NOTE ensure that grill assemblies are orientated
correctly so that the surface of the grill is sloping
forward to allow oil to drain into oil reservoirs.
5. Fit warming racks to splashguard at rear
front
assembled grill
base
grill orientation
bolt bolt

4 mounting optional side burner electrolux en:v barbecue
5. Assemble screws to side of trim panel loosely, allowing
clearance for the side burner trim panel to fit under
head of screw.
6. Slide side burner against main barbecue trim with
notches behind screw heads and then lower into position
7. Tighten screws to clamp side burner to main barbecue.
You may need to remove the control knob for screw
driver access.
8. Insert and tighten 4 screws securing brackets to corner
posts. Tighten screws previously fitted to bracket.
1. Release support rod ends from slots.
2. Remove side table mounting screws, and remove side
table. Re-fit screws without side table.
3. Remove lid, trivet and burner crown from side burner.
4. Fit brackets to side burner, do not tighten screws but
allow some movement for fitting.
Mounting optional side burner
Release rod from
slot by pushing
ends of rod toward
centre as shown
remove
mounting
screws
screws fit loosely
to allow side burner
to fit behind screw
head before tightening
notches to be placed over loose screw heads
top of bracket just
fits under trim before
lowering into position
slide side burner notches
over screw heads
and lower into position
Tighten screw using phillips head screwdriver.
Place screwdriver through holes to engage screws
Insert screws and
tighten each side
Insert screws and
tighten each side

electrolux en:v barbecue mounting optional side burner/gas specifications 5
9. Remove warmer drawer. Pull out warmer drawer and
release slides by actuating plastic lever on side of slides.
10. Locate connection hose and poke through side panel
hole.
11. Remove plug from end of hose and connect hose
to side burner valve. (use existing image) Once hose
fitment completed, fit drawer into place by carefully
placing slide runners each side into place and gently
push in fully.
12. Check for leaks at joins as described in “Leak test
procedure” section on page 7.
leak test this joint
with warmer drawer removed,
locate flexible hose and put
free end through hole of side panel
Gas specifications
For Electrolux En:V barbecue only
gas type universal LPG natural gas
Maximum gas consumption 50 MJ/h 50 MJ/h
Injector orifice diameter (mm) 0.95 1.75
Number of injectors 4 4
Regulator pressure 2.75 kPa 1.00 kPa*
For Electrolux En:V barbecue with optional side burner
gas type universal LPG natural gas
Maximum gas consumption 61 MJ/h 63.5 MJ/h
Injector orifice diameter (mm) 0.95 0.95 1.75 1.80
Number of injectors 4 1 4 1
Regulator pressure 2.75 kPa 1.00 kPa*
NOTES
• This appliance MUST be serviced only by a qualied
licensed person.
• This product is intended for outdoor use only.
• Ventilation holes in the unit must not be obscured by
the installation.
*The outlet pressure at the natural gas regulator will be
lower if the side burner is tted. The minimum allowable
pressure is 0.8 kPa
For conversion to Natural Gas a conversion kit will need to
be purchased from Electrolux Spare Parts.

6 safety information/installing gas cylinder electrolux en:v barbecue
Installing the gas cylinder
To install bottle:
1. Open both centre & right hand cabinet doors and pull
out sliding tray
2. Wind out clamp screw to allow base of bottle to fit
3. Place gas bottle into tray and tighten clamp to secure
bottle
4. Make connection of gas hose to gas bottle
Gas bottles vary in size and there may be some variations
that do not fit into the space provided. As an alternative to
mounting the gas bottle in slide out tray, the bottle can be
placed on the ground and hose placed through hole in side
panel for connection to inlet.
• This appliance is designed to use a Universal LPG 9kg
(20 lbs) gas cylinder.
• The gas cylinder must be made and marked in
accordance with specifications for LPG cylinders
• The isolation valve must be turned off when the
appliance is not in use.
• Gas cylinders must be stored in an approved housing
out of reach of children.
• When disconnecting the gas bottle ensure that all the
control valves are in the ‘OFF’ position.
• Remove the bottle from any housing in which it may be
stored before disconnection.
• When reconnecting the hose to the bottle, ensure that
all connections are tight before replacing in the storage
compartment.
• Carry out a leakage check as detailed below after each
reconnection.
Gas bottle safety information
clamp screw

electrolux en:v barbecue leak test procedure/conversion to natural gas 7
Leak test procedure (Universal LPG)
• Ensure all gas valves are in the ‘OFF’ position.
• In a small container, mix a solution of water and
detergent or soap.
• After connection of the hose, turn on the valve at the
gas bottle or mains as appropriate.
• Using a brush apply the solution to the gas connection
points and look for bubbles forming.
• Bubbling will indicate a leak.
• Turn off the valve and re-tighten the joint. Repeat the
leak test.
• If the leak persists, turn off the gas at the isolation
valves and contact a licensed gas fitter to correct.
leak test points
check hose for
signs of abrasions,
cracks or leaks
Conversion to Natural Gas
Preparing the unit for Natural Gas installation.
This barbecue is supplied set up for Universal LPG and is
labelled accordingly. A Natural Gas conversion kit can be
purchased from Electrolux Spare Parts to enable conversion
to Natural Gas use.
NOTE: Conversion of this unit to Natural Gas must be
carried out by a qualied licensed person and a Certicate of
Compliance must be issued to the owner on completion of
the installation and conversion.
The conversion kit consists of:
• Regulator
• Hose with quick connect bayonet tting one end
• Small plastic bag containing 4 brass injectors
• Natural Gas sticker
Procedure
1. Changing the injectors
• Remove warmer drawer as shown on page 5.
• Remove front service panel by loosening the screws in
3 places. Screws need only be loosened, and not fully
removed.
• Lift service panel from the bottom and swing out
approximately 45 degrees to release the top edge of
the service panel.
loosen 3 screws
on underside
of service panel
swing out to release
service panel

8 conversion to natural gas electrolux en:v barbecue
caution
• Take care when removing service panel not to
damage the metal tabs that support the panel on
either side.
• Release the burner retaining clip as shown
• Unscrew and replace the 4 injector nipples located in
the end of each tube feeding the burners. The Natural
Gas injectors have a 1.75mm diameter orifice in them.
The orifice appears substantially larger than those of
the Universal LPG injectors.
• Re-fasten the clip to retain the tube in the burner.
Do not over tighten or distort supply tube.
• Fit the front service panel back on and fasten screws.
If unit is fitted with side burner – the injector for this
burner must also be changed
• Remove lid, trivet, burner caps & burner crown
• Unscrew injector and replace with 1.80mm Natural
Gas injector (supplied with side burner)
• Replace burner crown & caps.
2. Disconnect brass adaptor and LPG hose and
regulator assembly from gas inlet connection
3. Connect the hose to the regulator
• Place threaded end of hose through hole in side panel.
• Apply thread tape or sealant to the male thread on the
hose and screw into the regulator.
4. Connect the regulator to the barbecue gas inlet
• Fit the regulator ensuring the blue sealing washer is in
place and the arrow is pointing in the right direction.
5. Replace the ‘gas type’ sticker
• Locate the ‘Universal LPG’ sticker located on the
barbecue gas inlet and remove it. Put the ‘Natural
Gas’ sticker in its place.
6. Leak test procedure
• Ensure all gas valves are in the ‘OFF’ position.
• In a small container, mix a solution of water and
detergent or soap.
• After connection of the hose, turn on the valve at the
gas bottle or mains as appropriate.
• Using a brush apply the solution to the gas connection
points and look for bubbles forming.
• Bubbling will indicate a leak.
• Turn off the valve and re-tighten the joint. Repeat the
leak test.
• If the leak persists, turn off the gas at the isolation
valves and contact a licensed gas fitter to correct.
injector
leak test points
check hose for
signs of abrasions,
cracks or leaks
service panel
fastened by
metal tab here
service panel
fastened by
metal tab here
hose with tapered thread
– thread tape required
natural gas regulator
barbecue gas inlet
Conversion to Natural Gas (cont.)

electrolux en:v barbecue choosing a location 9
7. Turndown adjustment
When converting to natural gas the turndown setting will
need to be adjusted to give a satisfactory flame on low
setting.
• Remove the 4 knobs from valve shafts of main
barbecue
• Remove rubber grommets from control panel holes
• Using the small at blade screwdriver provided, adjust
the turndown screw of each valve by turning anti-
clockwise 2 turns (see diagram)
• If optional side burner tted, remove the control knob
from valve shaft
• Using the small at blade screw driver provided, adjust
the turndown screw of valve by turning clockwise
approximately 1/4 turn (see diagram)
• Following connection of the gas and leak testing as per
previous steps, light all burners and set to high.
• One burner at a time, turn the valve shaft to lowest
setting, observe the flame and adjust the turndown
screw until a small steady flame is achieved.
• Repeat until all burners adjusted
• Once turndown settings adjusted, turn burners off and
replace rubber grommets and control knobs.
turndown screw
for valve
for optional side burner,
turn down screw inside
shaft with a small flat-blade
screwdriver
• The vertical clearance above the cooking surface to
any combustible materials must be at least 1000mm.
• Cooking with roasting hood closed vents the hot
flue gases out the rear of the appliance. A minimum
clearance of 450mm to any combustible materials is
required. This clearance should also be maintained for
brittle materials which may be affected, such as glass.
• Avoid windy conditions as this will affect cooking
performance and burner efficiency. If this situation
cannot be avoided some shielding may be necessary.
• The barbecue grills and hotplates are slightly sloped
to enable grease & oil drainage into front receptacles.
When choosing a location ensure that the slope
towards the front is maintained. If not, oil & grease may
run into the back of the burner box from the
grill channels.
Choosing a location

For safety, the wheel brake should be activated to prevent
any movement of the barbecue.
There are 2 wheel brakes.
To activate:
• Push down until it locks.
10 installation warnings/wheel brake electrolux en:v barbecue
wheel brakes
Activating the wheel brake
warning
• This appliance shall only be used in an above ground,
open air situation with natural ventilation without
stagnant areas, where gas leakage and products of
combustion are rapidly dispersed by wind or natural
convection. This barbecue has been designed for
outdoor use only. Refer to diagrams below.
• Never install this barbecue inside any building, garage,
shed or breezeway or inside a boat, caravan or
recreational vehicle. This is to prevent the possibility of
fire, carbon monoxide poisoning or asphyxiation.
• Any enclosure in which this appliance is installed shall
comply with one of the following:
– An enclosure with walls on all sides, but at least
one permanent opening at the ground level and no
overhead covering.
– Within a partial enclosure that includes an overhead
cover and no more than 2 walls.
– Within a partial enclosure that includes an overhead
cover and more than 2 walls, the following shall apply:
– at least 25% of the total wall area is completely
open and at least 30% of the remaining wall area
is open and unrestricted
• In the case of balconies, at least 20% of the total of
the side, back and front wall areas shall be and remain
open and unrestricted.
Outdoor area example 1
Outdoor area example 2
Outdoor area example 3
Outdoor area example 4
Outdoor area example 5
Installation warnings
both ends
open
open side at
least 25% of
total wall area
30% or more
in total of the
remaining wall
area is open and
unrestricted
open side at
least 25% of
total wall area
30% or more
in total of the
remaining wall
area is open and
unrestricted

important
Ensure flame tamers are positioned under the grill
panels
Left hand hotplate, right hand grill
Left hand half grill, central hotplate, right hand half grill
Left hand grill, right hand hotplate
electrolux en:v barbecue hotplate and grill configuration/operating instructions 11
Options for configuration of hotplates
and grills
Operating instructions
Control functions
Before lighting the barbecue:
• Check that all hoses and gas ttings are tight.
• Open the roasting hood.
• Check all control knobs are in the ‘OFF’ position.
• Ensure that the cooking surfaces are clean.
• Turn the gas isolation valve ‘ON’.
Lighting instructions
• Do not attempt to light burners with the cooking
surfaces covered.
• Read instructions before lighting.
• To light a burner, depress the knob and rotate to ‘RAPID
PREHEAT’.
• Hold for 3 seconds, release and check the ame.
• If burner did not light, turn knob to the ‘OFF’ position
Allow gas to disperse, then repeat lighting procedure.
Manual lighting
• If, in the event of the automatic ignition system not
working, the barbecue can be lit manually.
• Lift the front edge of the hotplate and grills, rotate the
knob to the ‘RAPID PREHEAT’ and place a lighted
match near to the burner intended to be lit.
• Once alight, repeat for other burners. Lower the grills
and hotplate, taking extreme care with hot surfaces and
flames.
Preheating
• This barbecue is tted with high power burners. In
most conditions it will only be necessary to preheat the
barbecue for 5 minutes before cooking can commence.
• As with most things, experience will familiarise you with
the effectiveness of and the time required to achieve the
desired preheating time to obtain the desired cooking
temperature.
• Testing has shown that the burners can be turned to
the low position for satisfactory cooking.
• If the unit does not operate correctly refer to the
troubleshooting section on page 15.
• If the burners are left to run too hot there will be
excessive smoking during the cooking process and
subsequent burning of the food being prepared. This
may also result in excessive flaring of the fat being
emitted from the food.
• Roasting with the hood closed only requires the 2
outermost burners to be on low setting for satisfactory
cooking. Refer to page 13 for further information on
roasting.
To turn the burner off
• When cooking is complete, rotate the knob fully
clockwise so the pointer on the knob is positioned at
the off position.
• Turn gas bottle isolation valve off after turning all knobs
to off position when appliance not in use.
grill panels flame tamers

12 side table/warmer drawer electrolux en:v barbecue
Using the warmer drawer
Using the Warmer Drawer
• The warmer drawer may be used to warm up crockery
prior to use
• During barbecue usage temperatures within the drawer
can exceed 80°C under some circumstances,
depending on the number and settings of burners in
use as well as the weather conditions. When accessing
the drawer use oven gloves to avoid burning
or scalding.
• When placing crockery into warmer drawer distribute
evenly, and do not exceed 15kg
• It is not recommended to use the warmer drawer for
food due to the risk of bacteria developing at
temperatures below 70°C
• Do not place ammable items in the drawer
• Do not store plastic items in the drawer
• Do not store aerosols or cleaning products in
the drawer
• The drawer can be used to store utensils when
barbecue not in use
warning
Do not place hands inside the warmer drawer
under barbecue. The base of the burner box can be
extremely hot.
Always fully pull out the warmer drawer to access.
Do not place hands
inside drawer and
under burner unit.
Always fully withdraw drawer.
To extend the side tables:
• Lift upwards until it locks.
To fold back into place:
1. Lift upwards slightly to unlock.
2. Slide support arms upwards and table should fall into
place.
Using the side table
Lift upwards
Lift upwards

electrolux en:v barbecue roasting hood/waste bin/side burner operation 13
Using the roasting hood
The waste bin
• Cooking with the hood closed only requires 2 burners to
be on low setting. Setting is to be adjusted depending
on conditions and using the temperature indicator as a
guide.
• It is recommended when roasting to place the solid
hot plate in the centre with one grill on each side of the
plate. Use the two outer burners under the grills.
• To achieve even cooking of the food, place the food
onto a wire rack above the hot plate to allow air to
circulate under the food.
• Food can also be placed on the warming racks for
cooking with hood closed
warning
• Do not use more than 2 burners when hood closed
and do not allow the temperature to exceed the
‘Ready’ zone of the temperature indicator. These
conditions create excessive heat and may cause
damage to the barbecue and roasting hood.
• When cooking with the hood closed the hot ue
gases flow out the rear of the appliance between
the splashguard and the hood. Ensure the barbecue
is suitably located to avoid damage or injury.
• The waste bin is seated in a frame mounted on
telescopic slides. The bin can be removed from the
frame for cleaning etc. Ensure the door is fully open
before pulling out the bin slide assembly to prevent
damage to the inner door.
• Do not place hot items into bin that may damage or
melt plastic.
Side burner operation
Control functions
Before lighting the side burner:
• Check that all hoses and gas ttings are tight.
• Remove lid.
NOTE The lid is designed as a cover for weather
protection. The lid is not designed to be used as a
cooking hood. During use the lid can be stored on the shelf
inside the cabinet below.
• Check control knob is in the ‘OFF’ position.
• Ensure that the cooking surfaces are clean.
• Turn the gas isolation valve ‘ON’.
Lighting instructions
• Do not attempt to light burners with the cooking
surfaces covered.
• Read instructions before lighting.
• To light a burner, depress the knob and rotate to ‘RAPID
PREHEAT’.
• If burner did not light, turn knob to the ‘OFF’ position.
Allow gas to disperse, then repeat lighting procedure.
Manual lighting
• If, in the event of the automatic ignition system not
working, the barbecue can be lit manually.
• Rotate the knob to the ‘RAPID PREHEAT’ and place a
lighted match near to the burner.
• Testing has shown that the burners can be turned to
the low position for satisfactory cooking.
• If the unit does not operate correctly refer to the
troubleshooting section on page 15.
• If the burner is left to run too hot there will be excessive
smoking during the cooking process and subsequent
burning of the food being prepared
To turn the burner off
• When cooking is complete, rotate the knob fully
clockwise so the pointer on the knob is positioned at
the off position.
tips and information
The side burner trivet is designed for use with a flat bottom
pan or for a wok. This is achieved by simply turning the
trivet over to suit the type of cooking desired. When using
flat bottom pan ensure pan base diameter is at least
150mm to ensure pan stability on trivet
“up” for wok
“down” for
flat bottom pan

14 cleaning and care electrolux en:v barbecue
The Electrolux En:V barbecue has been constructed from
select grade stainless steel which, if not cared for, may
discolour over time. To keep your barbecue looking its best
we recommend that the cooking surfaces are cleaned after
every use.
warning
Please ensure that your barbecue is switched off and
has cooled down before following the instructions
below.
Cleaning of Stainless Steel components
Hot Plate and Grill
• Remove all solid materials and excess grease from grill
and hotplate using scraper or wire brush
• To make cleaning easy, the two grill halves can be
removed with the hotplate. For stubborn stains, simply
soak the grill and plate components in hot soapy water
before rinsing thoroughly
• Ensure that all surfaces are dried with a clean dry cloth
• The hot plate & grill will discolour with high temperatures
when used. The discolouration is normal and does not
affect the durability or performance.
Other stainless steel surfaces
caution
Do not use abrasive or caustic cleaners, scourers
or metal scrapers on these stainless steel surfaces
as they may permanently scratch and damage your
barbecue.
• Wash all stainless steel components, including the
slimline lid, the roasting hood and control knobs with a
soft dishcloth using hot soapy water
• The barbecue interior can be wiped down with a soft
cloth in hot soapy water. The rear panel of the interior is
removable for easy cleaning
• Ensure that all surfaces are dried with a clean dry cloth
Cleaning and care
caution
Take extra care (particularly when cleaning on and
around the control knobs) to ensure that water and
soapy residue do not enter the control panel, where
the valves are or into the burners. Care should also be
taken not to disturb the spark electrode. A distance
of 5mm should be maintained between it and the
burners (see diagram below).
Cleaning the oil reservoirs
The Integrated barbecue has a unique oil management
system which uses overlapping channels to drain all oil
to the front into easily removed reservoirs and should be
cleaned after each use.
• To remove reservoirs, pull upwards from the front of the
barbecue and dispose of the contents of the catchment
responsibly. Rinse oil reservoirs in warm soapy water.
The reservoirs can be placed in the dishwasher if
desired.
Powder coated panels
Do not use abrasive or caustic cleaners, scourers or metal
scrapers as they may permanently damage your barbecue.
Wash all powder coated panels with a soft dishcloth using
warm soapy water. Ensure that all surfaces are dried with a
clean dry cloth.
Side Burner
The side burner contains aluminium fittings. Do not use
caustic based cleaners. Do not place burner bodies or caps
in a dishwasher. Check burner ports for blockages and
clear as required. If caps, crown and cup are heavily soiled,
use a non-abrasive cleaning compound.
Trivet
The trivet can be removed for cleaning. Clean by washing in
warm soapy water. Take care when replacing the trivets as
dropping them may damage the enamelled surface.
5mm

The ignition system
To change the battery unscrew the cover. Lift out the spring
and battery. Replace with a new AA battery and replace
the cover. Do not over-tighten the screw cover as this may
distort the trim panel. Test by depressing the knob and an
audible ‘clicking’ sound should be heard.
NOTE
Ensure that the battery has been placed in the correct
orientation.
Stainless steel burners
Burners should be checked at least once per year and
cleaned as necessary. Inspect burners to ensure no
residues have been deposited and gas ports are clear.
electrolux en:v barbecue maintenance/troubleshooting 15
problem possible cause remedy
Barbecue won’t
light
No gas Check isolation valve
is ON
Gas bottle empty – refill
or change gas bottle
Ignition system
not working
Check battery – should
hear a clicking noise
when the knob is
depressed
Replace battery
Manually light the
barbecue
Ignition electrode
wet or dirty
Gently clean and dry
electrode ensuring
position is correct
Excess smoke
being emitted
from the cooking
area
Gas valve set too
high
Turn gas valves down or
turn off selected burners
Smell of gas
DO NOT
ATTEMPT TO
LIGHT THE
APPLIANCE
Gas leak Turn off gas at the
isolation valves
Check for leaks, tighten
joints
If problem persists call
Electrolux Service
Troubleshooting
Side table timber
The hardwood used on lift up side tables has been treated
with a light coating of protection oil. Clean surface using a
soft sponge and a solution of mild soapy water. Wash down
afterwards with clean water.
To maintain strength, avoid discolouration and fading, the
timber must be protected using a suitable outdoor timber
furniture oil. Re-oiling of timber will need to be conducted at
regular intervals depending upon the amount of exposure to
the sun and rain.
Minor scuffs and scratches can easily be covered with a
coat of oil. Deep scratches need to be sanded out and
oiling concentrated in that area until the lustre is uniform.
Use of a weatherproof cover will help to minimise the
maintenance required.
tips and information
Special note on “tea staining”
Sometimes stainless steel surfaces are affected by a brown
discolouration called tea staining. This usually occurs in
areas which use high heat and can be easily removed using
specialised stainless steel cleaners. For best results, we
recommend that specialised cleaners be used regularly on
all stainless steel components. You will find these cleaners
at most hardware stores.
tips and information
Special note on stainless steel
The stainless steel panels may distort while in use but will
return to normal when cold. When the barbecue is not
being used it is recommended to keep it covered. If the
barbecue is to be stored indoors, remove the gas cylinder
and store the cylinder in a ventilated outdoor area.
Maintenance

This document sets out the terms and conditions of product
warranties for Electrolux branded appliances. It is an important
document. Please keep it with your proof of purchase documents in
a safe place for future reference should you require service for your
Electrolux appliance.
General Terms and Conditions
1. In this warranty
(a) ‘Electrolux’ means Electrolux Home Products Pty Ltd ABN 51
004 762 341 in respect of Appliances purchased in Australia and
Electrolux (NZ) Limited in respect of Appliances purchased in New
Zealand;
(b) ‘Appliance’ means any Electrolux product purchased by you
accompanied by this document;
(c) ‘Warranty Period’ means
(i) where you use the Appliance for personal, domestic or household
purposes in Australia the period of ‘24’ months and in New
Zealand the period of ‘24’ months;
(ii) where you use the Appliance for commercial purposes, in
Australia the period of ‘3’ months and in New Zealand the period
of ‘3’ months, (if the period stated is 0 months you are not
covered by this product warranty) following the date of original
purchase of the Appliance;
(d) ‘you’ means the purchaser of the Appliance not having purchased
the appliance for re-sale, and ‘your’ has a corresponding meaning.
2. This warranty only applies to Appliances purchased and used in
Australia or New Zealand and is in addition to (and does not exclude,
restrict, or modify in any way) any non-excludable statutory warranties
in Australia or New Zealand.
3. Electrolux warrants that, when dispatched from an Electrolux
warehouse, the Appliance is free from defects in materials and
workmanship for the Warranty Period.
4. During the Warranty Period Electrolux or its Authorised Service Centre
will, at no extra charge if your appliance is readily accessible without
special equipment, and subject to these terms and conditions, repair
or replace any parts which it considers to be defective. Electrolux or
its ASC may use reconditioned parts to repair your appliance. You
agree that any replaced Appliances or parts become the property of
Electrolux. This warranty does not apply to light globes, batteries, filters
or similar perishable parts.
5. Parts and Appliances not supplied by Electrolux are not covered by this
warranty.
6. Where you are within an Electrolux service area, this warranty covers
the cost of transport of the Appliance to and from Authorised Service
Centres of Electrolux and travelling costs for representatives of the
Authorised Service Centre to and from your home or business. If you
are outside an Electrolux service area, you will bear these costs. For
information about whether you are within an Electrolux service area,
please phone 13 13 49 in Australia, or 0800 10 66 10 in New Zealand.
7. Proof of purchase is required before you can make a claim under this
warranty.
8. You may not make a claim under this warranty unless the defect
claimed is due to faulty or defective parts or workmanship. Electrolux is
not liable in the following situations (which are not exhaustive):
(a) The Appliance is damaged by:
(i) accident
(ii) misuse or abuse, including failure to properly maintain or service
(iii)normal wear and tear
(iv) power surges, electrical storm damage or incorrect power
supply
(v) incomplete or improper installation
(vi) incorrect, improper or inappropriate operation
(vii) insect or vermin infestation.
(b) The Appliance is modified without authority from Electrolux in
writing.
(c) The Appliance’s serial number or warranty seal has been removed
or defaced.
(d) The Appliance was serviced or repaired by anyone other than
Electrolux or its Authorised Service Centres.
9. This warranty, the contract to which it relates and the relationship between
you and Electrolux are governed by the law applicable in the Australian
State where the Appliance was purchased or the law applicable in New
Zealand if the Appliance was purchased in New Zealand. Where the
Appliance was purchased in New Zealand for business purposes the
Consumer Guarantee Act does not apply.
Limitation of Liability
10.To the extent permitted by law:
(a) Electrolux excludes all warranties other than as contained in this
document;
(b) Electrolux shall not be liable for any loss or damage whether direct
or indirect or consequential arising from your purchase, use or non-
use of
the Appliance.
11.Provisions of the Trade Practices Act and State consumer legislation
in Australia, and the Consumer Guarantees Act, the Sale of Goods
Act and the Fair Trading Act in New Zealand, imply warranties or
conditions, or impose obligations, upon Electrolux which cannot be
excluded, restricted or modified. To the extent permitted by law, the
liability of Electrolux (if any) arising out of or in relation to the Appliance
or any services supplied by Electrolux shall be limited (where it is fair
and reasonable to do so),:
(a) in the case of Appliances, at its option, to the replacement or
repair of the Appliances or the supply of equivalent products or
the payment of the cost of replacing the Appliances or having the
Appliances repaired or of acquiring equivalent Appliances. Upon
being replaced, parts and Appliances become the property of
Electrolux; or
(b) in the case of services, at its option, to the supply of the services
again or the payment of the cost of having the services re-supplied;
and in the case of Appliances or services supplied in New Zealand,
loss or damage whether direct or indirect or consequential that is
reasonably foreseeable.
Privacy
You acknowledge that in the event that you make a warranty claim it will be
necessary for Electrolux and its Authorised Service Centres to exchange
information in relation to you to enable Electrolux to meet its obligations
under this warranty.
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
APPLIANCE: ELECTROLUX EN:V BARBECUE
Important Notice
Before Calling a Service Technician please check carefully the operating instructions, service booklet and the warranty terms and conditions.
FOR SERVICE
or to find the address of your nearest
state service centre in Australia
PLEASE CALL 13 13 49
For the cost of a local call (Australia only)
SERVICE AUSTRALIA
ELECTROLUX HOME PRODUCTS
www.electrolux.com.au
FOR SPARE PARTS
or to find the address of your nearest
state spare parts centre in Australia
PLEASE CALL 13 13 50
For the cost of a local call (Australia only)
FOR SERVICE
or to find the address of your nearest
authorised service centre in New Zealand
FREE CALL 0800 10 66 10
(New Zealand only)
SERVICE NEW ZEALAND
ELECTROLUX HOME PRODUCTS
www.electrolux.co.nz
FOR SPARE PARTS
or to find the address of your nearest
state spare parts centre in New Zealand
FREE CALL 0800 10 66 20
(New Zealand only)
16 warranty electrolux en:v barbecue