Electrolux T4130 User manual

Service manual
Torktumlare
T4130, T4130C
Quickdry, Quickdry C
Typ N1130
487 03 30 71/EN
2011.07.21
Service manual in original language

2

3
Service
manual
Contents
SafetyPrecautions.........................................5
Technicaldata.............................................7
Description of principal components. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Disassemblingthedryer....................................17
Periodicmaintenance......................................21
Optimizingtheairflow......................................25
Error codes (see Compass Control Service Manual)
Controls.................................................29
Sensors and overheating thermostats . . . . . . . . . . . . . . . . . . . . . . . . . 35
Doorswitch..............................................41
Motorandtransmission.....................................43
Heating(electric)..........................................47
Drumwithbearing.........................................51
Cabinet,doorreversal......................................55
RMC ...................................................57

Safety Precautions
Service
manual
4
4

5
Safety Precautions
Service
manual
5
Service
manual
Service
manual
Safety Precautions
Do not dry unwashed items in the machine
The machine is not to be used if industrial chemicals have been used for cleaning.
Do not allow minors to use the machine.
Do not hose down the machine with water.
The machine's door lock must under no circumstances be bypassed.
Items that have been soiled with substances such as cooking oil, acetone, alcohol,
petrol, kerosene, spot removers, turpentine, waxes and wax removers should be
washed in hot water with an extra amount of detergent before being dried in the
machine.
Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber
backed articles and clothes or pillows tted with foam rubber pads should not be
dried in the machine.
Fabric softeners or similar products should be used as specied by the fabric
softener instructions.
The machine may not be used to dry oor mops that contain polypropylene.
The nal part of a drying cycle occurs without heat (cool down cycle) to ensure that
the items are left at a temperature that ensures that the items will not be damaged.
WARNING. Never stop the machine before the end of the drying cycle unless all items
are quickly removed and spread out so that the heat is dissipiated.
Remove garments from the machine as soon as they are dried. This prevents them
from becoming creased and reduces the risk of spontaneous ignition.
If the machine develops a fault, this must be reported to the person in charge as soon
as possible. This is important both for your safety and that of others.
The machine must not be located where a door, sliding door, etc., can block the
machine's door
The machine is not intended to be used by people (including minors) with reduced
physical or mental capacity or lack of experience and knowledge. Such people must
be instructed in the use of the machine by a person who has responsibility for their
safety. Minors must be supervised to ensure that they do not play with the machine.
Adequate ventilation has to be provided to avoid the back ow of gases into the room
for appliances burning other fuels, including open res.
Gas heated tumble dryer:
The machine is not to be installed in rooms containing cleaning machines with
perchloroethylene, TRICHLOROETHYLENE or CHLOROFLUOROCONTAINING
HYDROCARBONS as cleaning agents.
If you can smell gas,
• Do not switch on any equipment
• Do not use electrical switches
• Do not use telephones in the building
• Evacuate the room, building or area
• Contact the person responsible for the machine
In order to prevent damage to the electronics (and other parts) that may occur as the
result of condensation, the machine should be placed in room temperature for 24 hours
before being used for the rst time.

6

7
2. Technical data
Service
manual
Contents
Technicaldata,typeT4130................................... 8
Technical data, motor specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Technical data
Service
manual

Technical data Service
manual
8
Technical data - type T4130/T4130C
Heating T4130 T4130C
Drum volume: 130 litres 130 litres
Weight net: 54 kg 57 kg
Drum: Diameter 575 mm 575 mm
Depth 500 mm 500 mm
Revolutions per minute 53 rpm 53 rpm
Capacity: Factor 1:25 5.2 kg 5.2 kg
Factor 1:33 3.9 kg 3.9 kg
Heat effect: Electric heating: 5.1/3.2 kW 3.0 kW
Air consumption: Heat effect 5.1 kW 210 m3/h -
Heat effect 3.1 kW 170 m3/h
Piping: Evacuation Ø 100 -
Pressure drop:
Evacuation max.
5.1 kW 80 Pa
3.1 kW 140 Pa
Sound power level: Lw<70 dB (A) <70 dB (A)

9
Technical data
Service
manual
Technical data - motor specifications
T4130 T4130C
Dryer with reversal:
Motor 3-phase:
Effect 130 W 130 W
Revolutions per minute: 50 Hz 2730 rpm 2730 rpm
60 Hz 3330 rpm 3330 rpm
Motor 1-phase:
Effect 130 W 130 W
Revolutions per minute: 50 Hz 2730 rpm 2730 rpm
60 Hz 3330 rpm 3330 rpm

10

11
3. Description of principal components
Service
manual
Contents
Description ..............................................12
Positionofcomponents.....................................14
11
Description of principal components
Service
manual

Description of principal components
Service
manual
12
Description
Dryer type T4130/T4130C are available as electric heated.
Programs - Compass Control
The dryer has a microprocessor. The microprocessor control has different functions
including:
• Drum reversing for less tangling of large items.
• Serviceprogram for adjustment parameters eg. temperature, cool-down time.
• Dryer functions monitoring - errors occurred during the program sequence are
registered in the log. Some of the error codes are shown on the display at the same
time.
• RMC (Residual Moisture Control), the dryer stops automatically when the clothes have
reached the required residual moisture level.
Knob operation for
Program selection
Door
Display

13
Description of principal components
Service
manual
Loading door
Normally the dryer has a right-hinged door.
The door is, however, reversible (see section "Cabinet, door reversal").
A door switch ensures that the dryer stops automatically if the dryer is opened during the
program sequence, see section "Door switch".
Knob operation
Turn and select with the knob operation and following appears:
• Program selection.
• Start button.
• Language selection.
Coin drop / card reader
The dryer can be mounted with a coin drop, a card-start system, or it can be prepared for
field installation of a card start system.
Motor
The dryer has one motor. The motor operates the blower and the drum.

82
3
1
5
5
5
6
2
Description of principal components
Service
manual
14
1. B1 Connection terminal
2. Ext Connection max.
1,25A 200-240V AC
3. TR1 Transformer
4. K4 Contactor, heat
5. Cn X/Y Capacitor
6. RC RC unit
7. C Motor operating capacitor
8. F10 Fuse T 2.5 A
9. PCB1 Selecta II
1. B1 Connection terminal
2. TR1 Transformer
3. K4 Contactor, heat
4. Cn X/Y Capacitor
5. RC RC unit
6. PCB1 Selecta II
200-240V 3 AC
400-415V 3 AC + N
400-480V + 3 AC
without N
1
56
7
9
43

10 2
6
1
4
3
7
9
8
5
10
2
3
4
5
6
7
7
7
9
8
15
Description of principal components
Service
manual
1. B1 Connection terminal
2. TR1 Transformer
3. K4 Contactor, heat
4. K1 Contactor (drum right)
5. K2 Contactor (drum left)
6. Cn X/Y capacitor
7. RC RC unit
8. PCB1 Selecta II
9. PCB5 Relay for M3
10. F10 Fuse T0.5 A
200-240V 3 AC, 230-240V 1 AC
400-415V 3 AC+N
1. B1 Connection terminal
2. Ext Connection max
1,25A 230V AC
3. TR1 Transformer
4. K4 Contactor, heat
5. Cn X/Y Capacitor
6. RC RC unit
7. C Motor operating
capacitor
8. PCB1 Selecta II
9. PCB5 Relay for M3
10. F10 Fuse T2.5 A
400-440V + 3 AC
without N
1

Description of principal components
Service
manual
16
T4130C:
Condensator C2 for fan motor, fig. 1.
2
1
T4130C:
Only 400-440V 3 AC without N
Autotransformer TR2 for condensate pump
and fan motor, fig. 2.

Disassembling the dryer
Service
manual
17
Content
Disassembling the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Disassembling the dryer
Service
manual
18
Recommended sequence
1. Disconnect the power supply.
2. Dismount the top plate and the heat shield,
fig. 2.
Warning! After disconnecting the
power, there might still be power on the
suppression capacitor. It can be discharged
by pushing down the heating contactor with
a screwdriver, fig. 1.
3. Dismount the protective screen at the air
vent (Standard tumble dryer). Dismount the
plastic cover (Condensate tumble dryer),
fig. 3.
4. Loosen the drive belt on the drum from the
motor and pull out the hose to the drain,
fig. 4.
1
2
3
34
Suppression
capacitor
Heating
contactor

Disassembling the dryer
Service
manual
19
5
6
Recommended sequence
5. Release the bearing rollers: Loosen the
screws and turn the hexagon key 1/2 turn
clockwise, fig. 5.
6. Dismount the discharge branch and the
multi-plug for the fan (Condensate tumble
dryer), fig. 6.
7. Dismount the heat cover and disengaged
the heat element cables.
8. Cut the cable ties. Carefully pull the
cables in through the hole and keep the
platic ring around the cables, fig. 7 + 8.
8
7

Disassembling the dryer
Service
manual
20
Recommended sequence
9. Remove the spade-shaped connector for
the earthing conductor (A) and the sliding
contact (B). Remove the cable from the
terminal strip (C), fig. 9.
Note! The earth conductor must be
connected again for safety.
10. Remove the four screws at the heating
element.Remove the back plate, fig. 10.
11. Lift the drum and the back plate jointly out
of the cabinet, fig. 11.
9
A
C
11
B
10