Electrolux TRIMKITSS2 User manual

E|ectro|ux iNSTRUCTION SHEET
U19 All Refrigerator and All Freezer Trim Kit Installation
Product Line: U19 All Refrigerator and A! Freezer Models
Models: EI32AR65JS E32AR75JPS FPRH19D7LF
EI32AF65JS E32AF75JPS FPUH19D7LF
Serial Number Range: All Serial number ranges
Single Trim Kit Components
Parts Included in Kit TRIMKITEZ1 (Part# 297333500):
Kit for Models: FPRH19D7LF and FPUH19D7LF
Single Trim Kit 297333500
ITEM PART NUMBER
1 297349000
2 297349001
3 297332701
4 297332801
5 297333301
6 297337700
7 297343201
8 297276900
DESCRIPTION
Trim Side RH U19
Trim Side LH U19
Trim Top Short U19 Single
Trim Top Tall U19 Single
Kick Plate U19 Single
Carton, Packaging
Hardware Pack Single U19
Lever Assembly Support System
QTY
1
1
1
1
1
1
1
2
Parts included in Kit TRIMKITSSI (Part# 297333510):
Kit for Models: EI32AR65JS and EI32AF65JS
E32AR75JPS and E32AF75JPS
Single Trim Kit 297333510
ITEM PART NUMBER
1 297349010
2 297349011
3 297332711
4 297332811
5 297333311
6 297337700
7 297343201
8 297276900
DESCRIPTION QTY
Trim Side RH U19 1
Trim Side LH U19 1
Trim Top Short U19 Single 1
Trim Top Tall U19 Single 1
Kick Plate U19 Sngle 1
Carton, Packaging 1
Hardware Pack Single U19 1
LeverAssembly Support System 2
[
[
Single Trim Kit Front View _ _8
.4--1
.4--2
4
NOTE: All Hardware Pack components mentioned
throughout this instruction sheet will have an "H"
after the item number.
Hardware Pack 297343201
ITEM PART NUMBER
1H 297333900
3H 297236250
5H 050149
6H 297142600
7H 297299700
DESCRIPTION QTY
Tie-Bar Hinge 1
Screw 1/4-20 x .63 8
Screw TH #8-18 x .75 AB 6
Screw FH #8-32 x .63 2
Installation Instructions 1
5H 6H
/
0 0 O O
1.25"Ref 000 000
6.25" Ref
Hardware Pack 297343201
@2011Etectrolux Home Products,Inc. Instruction Sheet 297299700 Rev. B 02.09.11

E|ectro|ux iNSTRUCTION SHEET
Dual Trim Kit Components
Parts Included in Kit TRIMKITEZ2 (Part# 297333600):
Kit for Models: FPRH19D7LF and FPUH19D7LF
Double Trim Kit 297333600
ITEM PART NUMBER
1 297336900
2 297349000
3 297349001
4 297332700
5 297332800
6 297333300
7 297337700
8 297343200
9 297276900
DESCRIPTION QTY
Center Trim U19 1
Trim Side RH U19 1
Trim Side LH U19 1
Trim Top Short U19 Dual 1
Trim Top Tall U19 Dual 1
Kick Plate U19 Dual 1
Carton, Packaging 1
Hardware Pack Dual U19 1
Lever Assembly Support System
Parts Included in Kit TRIMKITSS2 (Part# 297333610):
Kit for Models: EI32AR65JS and EI32AF65JS
E32AR75JPS and E32AF75JPS
Double Trim Kit 297333610
ITEM PART NUMBER
1 297336900
2 297349010
3 297349011
4 297332710
5 297332810
6 297333310
7 297337700
8 297343200
9 297276900
DESCRIPTION QTY
Center Trim U19 1
Trim Side RH U19 1
Trim Side LH U19 1
Trim Top Short U19 Dual 1
Trim Top Tall U19 Dual 1
Kick Plate U19 Dual 1
Carton, Packaging 1
Hardware Pack Dual U19 1
LeverAssembly Support System 4
Front View
Double Trim Kit
-tml
I-_4
NOTE: All Hardware Pack components mentioned
throughout this instruction sheet will have an "H"
after the item number.
Hardware Pack 297343200
ITEM PART NUMBER
1H 297333900
2H 297333901
3H 297236250
4H 297337000
5H 050149
6H 297142600
7H 297299700
DESCRIPTION
Tie-Bar Hinge
Tie-Bar Back
Screw 1/4-20 x .63
Screw FH 1/4-20 x .63
Screw TH #8-18 x .75 AB
Screw FH #8-32 x .63
Installation Instructions
Ref |
Hardware Pack 297343200
6H 3H
© © ©
000 o
6.25" Ref
1.25"
Ref
QTY
2
1
18
4
8
2
1
5H
O0
0 0 ! 2H
2.62" Ref
1H
@2011 Etectrolux Home Products, Inc. Instruction Sheet 297299700 Rev. B 02.09.11

E|ectro|ux iNSTRUCTION SHEET
TRIMKITEZ1 (Part# 297333500) &TRIMKITSSI (Part# 297333510) Trim Kit Dimensions
75.00 _+.06"
(1905 ram) 79.00 + .06"
2006.5 + 1.5mm)
(641mm) .j
(rain.) ._ _-.\\
33.00 + .032"
...._. (838 + .8mm)
75.09"
(1907 ram)
34.74"
(882 ram) _-_
J
34.74"
__ (882 mm) _
l
m
79 09"
(2009 ram)
@2011 Etectrolux Home Products, Inc. Instruction Sheet 297299700 Rev. B 02.09.11

E|ectro|ux iNSTRUCTION SHEET
TRIMKITEZ2 (Part# 297333600) & TRIMKITSS2 (Part# 297333610)Trim Kit Dimensions
79.00 _4-.06"
_+1.5mm)
75.00 _+.06"
(1905 mm)
67.12"
(1705 mm)
(17! 0 _
l
67.12"
(1705 mm)
79.09"
(2009 ram)
Safety:
Tools Needed:
• Phillips TMScrewdriver
• Flathead Screwdriver
• Safety Glasses
Always wear safety glasses when using power tools.
•Adjustable Wrench to fit 1-1/4"
• 3/8" Socket Wrench
• 7/16" Socket Wrench
• Step Ladder
• Tape Measure (min. 7" length)
• Drill & 1/8" Bit
Before You Begin
• Be careful when unpacking components. Do not use sharp objects when removing packaging material. This may
scratch the surface of trim components.
• Use extreme care when handling the metal trim pieces, Corners are very sharp and easily damaged if dropped,
@2011 Etectrolux Home Products, Inc. Instruction Sheet 297299700 Rev. B 02.09.11

E|ectro|ux iNSTRUCTION SHEET
Setting Up The Trim And Grill Assembly
(Single and Dual installations)
,Lay the parts out on a cleared area face down. Be
sure to place a drop cloth over the floor to prevent
scratching trim kit and/or floor. (See Figure 1).
! !_F !
li !i
::Ji J ! i
' i i
ii
Drop
Cloth
Figure 1.
2. Cut 4" (101.6mm) off the left and right Side Trim
using the slot as a guide to make the proper size for
a 75" (1905mm) cut-out. (See Figure 2).
NOTE: DO NOTcut the side trim if installing in a 79"
(2006mm) opening.
Side
Le_ and
Right Sides /
Y
4"
(101.6mm)
J
Leveling System Install
(Single and Dual Installations)
3. a. Lie unit on its back on packaging material or a
drop cloth to prevent damage.
b. Remove (3) screws from each side and discard.
(See Figure 3)
c. Remove and save both plastic leg levelers to use
in the next step.
,
Figure 3.
a. Attach the current leg leveler to leveling system.
The leg leveler is a common part that will work
on both bottom sides of the unit. (See Figure 4).
b. Attach leg leveler with three (3) screws per side
using a 3/8 socket.
c. Re=install the leg levelers.
d. In order to provide clearance to access the rear
screw hole, adjust the rear roller up out of he
way. When finished, lower the rear roller back to
its initial position.
Figure 4.
@2011 Etectrolux Home Products, Inc. Instruction Sheet 297299700 Rev. B 02.09.11

E|ectro|ux iNSTRUCTION SHEET
Trim Kit installation
installing Trim Kit Tie Bar
(Dual installation Only)
NOTE: Leveling may be required to line up the holes
in steps "a" and "d".
5. a. Tie units together by securing the mounting
bracket at the back of the units with a
3/8" socket. (See Figure 5).
b. Install center strip to insure the proper 3/8" gap
is maintained between units. (See Figure 6).
c. Tie units together with the common mounting
bracket at the front top with two screws in
the inner two screw holes by using a 3/8" socket,
(See Figure 7)
d. Tie units together with common mounting
bracket at the bottom front using #3 Phillips
driver. (See Figure 8)
3/8" Gap
3H
Figure 5.
3/8" Gap Between Units
3/8" Center Strip
Item 1 Dual kit
Figure 6.
Item 1H
Figure 8.
Trim Kit installation (Single Unit installation)
6. Remove outer screw from top hinge using a 3/8"
socket driver or wrench and save for later. Install
mounting bracket with one screw mounted to inside
hole using a 3/8" socket, (See Figure 9).
Screw
Figure 9.
Side Trim installation
(Single and Dual Installations)
7. a. Position Left Hand Side Trim on cabinet trim with
bottom resting on the floor.
b. Drill the 1/8" (3mm) pilot hole.
c. Run screw in all the way and then back out.
Remove side trim for later install.
(See Figure 10).
NOTE: Some cabinet substrates may require pre-drilling
holes using a 1/8" (3mm) diameter drill bit.
Figure 7.
@2011 Etectrolux Home Products, Inc. Instruction Sheet 297299700 Rev. B 02.09.11

E|ectro|ux iNSTRUCTION SHEET
=a. Position Right Hand Side Trim on cabinet trim
with bottom resting on the floor.
b. Drill the 1/8" (3mm) pilot hole.
c. Run screw in all the way and then back out.
Remove side trim for later install,
(See Figure 10).
Left Side Right Side
Figure 10.
Top Trim install
(Single and Dual Installations)
NOTE: Step ladder required for installing top trim
components.
9. a. Remove outer hinge screw common on both
sides for a dual installation, (for a single
installation this screw is removed in Step 6.
Align the top trim and attach with a 3/8" socket.
Repeat for opposite side. (See Figure 11).
b. (Dual installation only) Install outer screws on
common mounting bracket, align top trim and
attach with 3/8" socket. (See Figure 12).
H
Figure 11.
Figure 12.
10. 75" (1905mm) High Opening With Top Trim
(Single and Dual Installations)
a. Slide units into place. Adjust height so top trim
height reaches 75.09" (1907mm). Center units
in opening and level. (See Step 12 for leveling
instructions)(See Figures 13 and 14)
b. Drill 1/8" (3mm) pilot holes and fasten screws
with a Phillips driver to kitchen cabinets,
Cabinet
Figure 13.
Figure 14.
11. 79" (2006mm) High Opening With Louvered Top
Trim (Single and Dual Installations)
a. Slide units into place. Adjust height so top trim
height reaches 79.09" (2009ram). Center units
in opening and level. (See Figure 15)
b. Drill 1/8" pilot holes and fasten two (2) screws
per side with a Phillips driver to kitchen cabinets,
' L 5H
J
Item 4 Single Kit
or
Item 5 Dual Kit
Figure 15.
@2011 Etectrolux Home Products, Inc. Instruction Sheet 297299700 Rev. B 02.09.11

E|ectro|ux iNSTRUCTION SHEET
12. Trim Kit Leveling (See Figure 16)
(Single and Dual Installations)
a. To raise front of unit, turn leg leveler to left with
adjustable wrench to fit 1-1/4" hex.
b. To raise back of unit, adjust bolt clockwise with
3/8" socket or flat head screwdriver
14. Side Trim Attachment to Kitchen Cabinets
(Single and Dual Installations)
a. Fasten bottom of side trim with screw.
(See Figure 17)
b. Fasten screws to top trim. (See Figure 18)
i_{11
To raise or lower door, [
adjust7/16" bolt. _ ,__}1
®
©
To raise back of _
unit, adjust bolt
clockwise.
3/8" Bolts
Phillips Head
Screws
Leg Leveler
Figure 16.
13. Hinge Adjustment (See Figure 16)
(Single and Dual Installations)
a. The bottom hinge is designed to make final
minor adjustments for door to door and door to
cabinet alignment.
b. Hinge will move side to side 3/32" and raise up
1/8".
Use a 7/16" socket or open end wrench to raise or
lower the door.
Use a 3/8" socket and a Phillips screwdriver to
loosen bottom hinge. Shift door left or right, then
retighten screws and bolts.
Figure 17.
Figure 18.
15. Kick Plate Attachment
(Single Unit)
(Dual Unit)
Attach the kick plate to the cabinet with
two (2) screws. (See Figure 19)
Attach the kick plate to the cabinet with
four (4) screws. (See Figure 20)
j5
Figure 19.
Screws Screws
Figure 20.
@2011 Etectrolux Home Products, Inc. Instruction Sheet 297299700 Rev. B 02.09.11