Electrolux E30MO75HSSA User manual

Installation and service must be pefformed byaqu , i lstaller.
IMPORTANT: Save for local electrical inspector s use,
Read and Save these instructions for future
Th e e lectricalreq u ire m ents fo r t his ova n a re 120vo Itsi 15 a rnps!
2,
3,
4,
5,
NOTE
Base must be capable of supporting 150 pounds (68.0
kg) for the Microwave Wall Oven only.
Make sure base is level and front of cabinet is square. If
the cabinet base is not level, the oven will tend to slide
out when opening the door.
Minimum required distance is 36" (91.44 cm) from the
floor.
The outlet should not be located in the shaded area of
Figure 1. It is required the outlet be a dedicated 120
volts with a 15amp rating for the appliance.
Minimum required distance between the Microwave
Oven and the wall oven cutouts should be at least 3
inches. The actual visible space will be reduced due to
the overlap of the Microwave Oven lower vent and the
wall oven.
Figure I
All dimensions are in inches (cm).
TINSEB504MRRO

iMPORTANT NOTES TO
THE iNSTALLER iMPORTANT SAFETY iNSTRUCTiONS
,
,
Read all instructions contained in these installation
instructions before installing the Microwave Wall Oven.
This oven can be built into a cabinet or wall by itself or
above any electric wall oven or warming drawer.
Remove all packing material from inside the oven cavity
before connecting the electrical supply to the Microwave
Wall Oven. DO NOT REMOVETHE WAVEGUIDE COVER,
which is located on the cavity ceiling. See Figure 2A.
Waveguide Cover
Oven Cavity
Door Seals
and Sealing
Surfaces
Hinge
Safety
Door Latch
ventilation can be dangerous.
Carpentry
Refer to Figure 1 for the dimensions required for your
appliance, and the space necessary to install the oven. The
oven support surface should be solid plywood or similar
material, the surface must be level from side to side and
from front to rear.
Electrical Requirements
The appliance operates on a 120 volt, 60 Hz electrical
supply with a separate ground wire. Provide a separate
circuit with a fuse or circuit breaker rated for 15 amps.
Observe all governing codes and local ordinances
,
,
Figure 2A Figure 2B
Remove the 2 shipping duct supports (see Figure 2B) by
removing the 2 screws securing each side. Reinsert 2
screws (each side) to secure the stainless cover.
Remove the feature sticker, if there is one, from the
outside of the door.
T0p"event damage to the oven contio!: duiing _old
ternperature weather, wait at least three (3)hours
after receiying this oven before supplyieg power to
the appliance. Thiswill prevent possibledamage to the
buiBin ovencontrol at power on.
,Check the oven for any damage, such as misaligned or
bent door, damaged door seals and sealling surfaces,
broken or loose door hinges and latches and dent
inside the cavity or on the door.
AUTHORIZED SERVICER
6. Observe all governing codes and local ordinances.
7. Be sure to leave these instructions with the consumer.
iMPORTANT NOTE TO
THE CONSUMER
Keep these instructions with your Owner's Guide for future
reference.
Cabinet Installation
The Mkrowave Wall oven can tip when the door
is open, The Anti-Tip brackets supplied with th e
Microwave Wall Oven must be attached to the
cabinet and the appliance t0 prevent tipping of
the unit and injury to persons;
,
ANTI41P BRACKETS INSTALLATION
INSTRUCTIONS
Unpack the Microwave Wall Oven and find the 2
Anti-Tip brackets and screws included in the literature
package.
Install the Anti-Tip bracket in the cabinet as shown
on Figure 3. Note: To prevent damage to cabinet, it
is recommended to drill 1/16"(0.16 cm) diameter pilot
holes before installing the Anti-Tip brackets.
E2

MICROWAVE WALL OVEN iNSTALLATiON
hold the door handle when moving the oven.
,
,
Place the oven adjacent to the opening on a table or
stand. Plug the power supply cord into the electrical
outlet. Carefully guide the oven into the prepared
opening. Avoid pinching cord between oven and wall.
See Figure 4. Push the unit in and against the cabinet.
The oven side bracket will clip into the Anti-Tip brackets.
See Figure 3.
To pull out the oven for servicing, open the door and
locate the two holes on the side frame. Simultaneously
insert the tools provided with the appliance in both
holes and pull the oven towards you. See Figure 5.
Cutout Width
(Seedimensions below)
r ............................
m m
16-1/2"
(41.9 cm)
Cutout Height
21" (53.3 cm) Min.*
21-1/2" (54.6 cm) Max.*
27-INCH MICROWAVE Cutout Width
25-1/8" (63.8 cm) Min3
25-5/8" (65.1 cm) Max3
25-3/8" (64.5 cm) Recommended _
30-INCH MICROWAVE Cutout Width
27-5/8" (70.2 cm) Min3
28-1/8" (71.4 cm) Max3
27-7/8" (70.8 cm) Recommended _
30-INCH CONVECTION Cutout Width
28-1/2" (72.4 cm) Min3
29" (73.7 cm) Max3
28-3/4" (73.0 cm) Recommended _ Figure 3
Figure 4Figure 5
E3

Model and Serial Number Location
The serial plate is located on the oven front frame. See
Figure 6.
When ordering parts for or making inquires about your
oven, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate on
your oven.
Before You Call for Service
Refer to the warranty in your Use & Care Guide for our
toll-free service number and address. Please call or write
if you have inquiries about your product and/or need to
order parts.
Serial
Plate Menu
Label
Figure 6
E4