Electrolux E32AR75FPS Operating manual

Publication #5995556346 January 2010
Technical Service Manual
ICON All Refrigerator and
All Freezer - Professional Series

Basic Information
1-1
Safe Servicing Practices For All Appliances
Avoid personal injury and/or property damage by observing important Safe Servicing Practices.
Following are some limited examples of safe practices:
1. DO NOT attempt a product repair if you have any doubts as to your ability to complete the repair in a safe and
satisfactory manner.
2. Always use the correct Replacement Parts as indicated in the parts documentation. Substitutions may defeat
compliance with Safety Standards Set For Home Appliances. Do not exceed maximum recommended wattage
on light bulb replacements. Doing so could blow fuses and/or damage transformers.
3. Before servicing or moving an appliance:
• Remove power cord from the electrical outlet, trip circuit breaker to the OFF position, or remove fuse.
• Turn off water supply if applicable.
4. Never interfere with the proper operation of any safety device.
5. Use ONLY REPLACEMENT PARTS CATALOGED FOR THIS APPLIANCE. Substitutions may defeat
compliance with Safety Standards Set For Home Appliances.
6. GROUNDING: The standard color coding for safety ground wires is GREEN, or GREEN with YELLOW
STRIPES. Ground leads are not to be used as current carrying conductors. It is EXTREMELY important that
the service technician reestablish all safety grounds prior to completion of service. Failure to do so will create
a hazard.
7. Prior to returning the product to service, ensure that:
• All electrical connections are correct and secure.
• All electrical leads are properly dressed and secured away from sharp edges, high-temperature components,
and moving parts.
• All non-insulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal
parts and panels.
• All safety grounds (both internal and external) are correctly and securely connected.
• All panels are properly and securely reassembled.
© 2010 Electrolux Home Products, Inc.
ATTENTION!!!
This service manual is intended for use by persons having electrical and mechanical training and a level
of knowledge of these subjects generally considered acceptable in the appliance repair trade. Electrolux
Home Products, Inc. cannot be responsible, nor assume any liability, for injury or damage of any kind
arising from the use of this manual.

Basic Information
This Manual has been prepared to provide Electrolux Service Personnel with Operation and Service Information for an
Electrolux All Refrigerator and/or All Freezer Pro Units, Models Numbers E32AR75FPS, E32AF75FP, E32AR75GTT
and E32AF75GT.
Table of Contents
1-2
Section 1 Basic Information ................................. 1-1
Safe Servicing Practices For All Appliances............. 1-1
Table of Contents ..................................................... 1-2
Important Safety Instructions.................................... 1-4
Child Safety .............................................................. 1-4
Proper Disposal of Refrigerators/Freezers ............... 1-4
Major Appliance Warranty Information ..................... 1-5
Model Number Breakdown....................................... 1-6
Serial Number Breakdown........................................ 1-6
Built-in All Refrigerator Specifications ...................... 1-6
Understanding Features and Terms - Refrigerator... 1-7
Built-in All Freezer Specifications............................. 1-8
Understanding Features and Terms - Freezer ......... 1-9
Section 2 Installation.............................................. 2-1
Warnings and Safety ................................................ 2-1
Installation Checklist ............................................... 2-2
Location.................................................................... 2-3
Leveling .................................................................... 2-3
Leveling Instructions For All Refrig./Freezer Pairs ... 2-4
Electrical Information ............................................... 2-4
Cut-Out Dimensions ................................................ 2-5
Optional Accessories ... ........................................... 2-5
Water Supply............................................................ 2-6
Connecting the Water Valve to the Ice Maker.......... 2-7
Trim And Riser Kit Installation Instructions............... 2-8
Setting Up The Trim And Grill Assembly .................. 2-9
Installing Trim & Grill Assembly Into Cabinetry ........ 2-10
Installing The Riser Kit.............................................. 2-11
Leveling The Refrigerator And Freezer .................... 2-14
How To Adjust Front And Rear Levelers.................. 2-14
Final Positioning ....................................................... 2-14
Care & Cleaning Of Your Trim Kit ............................ 2-15
Door Removal .......................................................... 2-15
Door Handle Mounting Instructions .......................... 2-15
Section 3 Electronic Control.................................. 3-1
Electronic Temperature Control ................................ 3-1
Power Up ................................................................. 3-1
Temperature Setting Selection ................................ 3-1
Fail Safe Mode ......................................................... 3-1
Error Indication ........................................................ 3-1
Exiting Fail Safe Mode ............................................. 3-1
Initiate Diagnostics Mode ........................................ 3-2
Diagnostics Indicator ................................................ 3-2
Defrost Timing ......................................................... 3-2
Manual Defrost Mode .............................................. 3-2
Showroom Mode ..................................................... 3-2
Compressor Run Time (CRT) Display Mode ........... 3-2
Compressor Delay Start ........................................... 3-2
Memory Retention .................................................... 3-2
Voltage Range .......................................................... 3-3
Stuck Key.................................................................. 3-3
Main Power Connector ............................................. 3-3
Section 4 Ice Maker ................................................ 4-1
Side Mounted Ice Maker .......................................... 4-1
Ice Maker Components ........................................... 4-2
Installing Water Supply Line to Ice Maker................. 4-4
Water Valve Switch – Water Fill Volume ................... 4-4
Test Cycling Ice Maker ............................................. 4-4
Operating Cycle Illustrations - Manual Cycle............ 4-5
Operating Cycle Illustrations - Electrical .................. 4-5
Operating Cycle Illustrations - Mechanical .............. 4-12
Section 5 Sealed System .................................... 5-1
Notes ........................................................................ 5-1
Soldering .................................................................. 5-1
Introduction............................................................... 5-2
Compressor Oils....................................................... 5-2
Refrigeration Systems .............................................. 5-2
Sealed System Repair.............................................. 5-2
Service Diagnostic Tips ............................................ 5-3
Refrigerator and Freezer Air Temperatures .............. 5-3
Line Voltage .............................................................. 5-3
Basic Components ................................................... 5-4
Testing for Refrigerant Leaks.................................... 5-4
Checking For Internal Leaks..................................... 5-4
Definitions................................................................. 5-5
Equipment Needed for Evacuation & Recharging .... 5-5
Low/High Side Leak or Undercharge........................ 5-6
Precautions For Charging Sealed Systems.............. 5-6
Flushing The System With Nitrogen ......................... 5-6
Compressor Oil Contamination ................................ 5-7
Recovering Refrigerant............................................. 5-8
Installing a New Compressor.................................... 5-9
Condenser Replacement.......................................... 5-10
Filter-Drier Installation .............................................. 5-10
Evaporator and Suction Line Replacement .............. 5-10
Installing Evacuation and Recharging Equipment.... 5-11
Evacuating System................................................... 5-11
Charging The System............................................... 5-12
Final Leak Test.......................................................... 5-12
Dedicated Equipment .............................................. 5-13
Vacuum Pump Maintenance..................................... 5-13
Spills or Leaks .......................................................... 5-14

Basic Information
1-3
HFC 134a Comparison With CFC 12 ..................... 5-15
Inhalation Toxicity ................................................... 5-15
Cardiac Sensitization.............................................. 5-15
Skin and Eye Contact............................................. 5-15
Combustibility of HFC-134a.................................... 5-16
Bulk Delivery and Storage...................................... 5-16
Filling and Charging Operations............................. 5-16
Refrigerant Recovery Systems............................... 5-16
Thermal Decomposition ......................................... 5-16
R-134a Physical Properties ................................... 5-18
HFC-134a, CFC-12 Pressure Temperature Chart .. 5-18
Terms and Global Warming ................................... 5-19
Section 6 Component Teardown ........................... 6-1
Safety Warnings ....................................................... 6-1
Refrigerator Exterior Components............................ 6-2
Door Handle .......................................................... 6-2
Kickplate ............................................................... 6-2
Door Hinge and Door Assembly............................ 6-2
Door Stop Assembly ............................................. 6-3
Door Gasket and Inner Panel ............................... 6-3
Door Hinge and Door Assembly............................ 6-3
Door Storage Components....................................... 6-4
Adjustable Door Bins............................................. 6-4
Dairy Door ............................................................. 6-4
Door Switch .............................................................. 6-4
Interior Components................................................. 6-5
Adjustable Interior Shelves.................................... 6-5
Refrigerator Drawer Assembly .............................. 6-5
Air Filter ................................................................. 6-6
Control Box Assembly ........................................... 6-6
Light Fixture........................................................... 6-6
Control................................................................... 6-7
Water Filter Base Components ............................. 6-7
Baffle Plate ........................................................... 6-8
Evaporator Cover .................................................. 6-8
Mid Level Lighting.................................................. 6-8
Thermistor ............................................................ 6-9
Evaporator Fan Assembly .................................... 6-9
Defrost Thermostat................................................ 6-10
Defrost Heater ....................................................... 6-10
Evaporator............................................................. 6-11
Compressor Area Components
All Refrigerator and All Freezer-Pro Models............. 6-12
Power Cord............................................................... 6-12
Water Valve............................................................... 6-12
Theater Lighting Control........................................... 6-13
Filter-Drier................................................................. 6-13
Compressor.............................................................. 6-14
Drain Pan.................................................................. 6-15
Condenser Fan Motor............................................... 6-15
Condenser Coil......................................................... 6-16
Section 6 Component Teardown (continued)
Freezer Exterior Components
Door Handle .......................................................... 6-17
Kickplate ............................................................... 6-17
Door Hinge and Door Assembly............................ 6-17
Door Bin ............................................................... 6-18
Tilt Out Wire Shelf . ............................................... 6-18
Door Stop Assembly.............................................. 6-18
Door Gasket and Inner Panel ............................... 6-19
Door Switch ........................................................... 6-19
Interior Components................................................. 6-20
Adjustable Interior Shelves.................................... 6-20
Freezer Drawer Assembly ..................................... 6-20
Air Filter ................................................................. 6-21
Control Box............................................................ 6-21
Light Fixture .......................................................... 6-21
Control .................................................................. 6-22
Baffle Plate............................................................ 6-22
Ice Maker............................................................... 6-22
Mid Level Lighting.................................................. 6-23
Thermistor ............................................................ 6-23
Evaporator Fan Assembly ..................................... 6-24
Defrost Thermostat ............................................... 6-24
Defrost Heater ....................................................... 6-25
Evaporator ............................................................ 6-25
Section 7 Parts List ................................................ 7-1
Models E32AF75FPS and E32AR75FPS shown
All Freezer Pro Door Exploded View ......................... 7-1
All Freezer Pro Cabinet Exploded View..................... 7-2
All Freezer Pro System Exploded View ..................... 7-4
Ice Maker Exploded View .......................................... 7-6
All Refrigerator Pro Door Exploded View................... 7-8
All Refrigerator Pro Cabinet Exploded View..............7-10
All Refrigerator Pro System Exploded View ..............7-12
Section 8 Troubleshooting..................................... 8-1
Troubleshooting Chart ............................................... 8-1
Section 9 Wiring Schematics................................. 9-1
Ice Maker Schematic ................................................ 9-1
All Freezer Pro Wiring Diagram ................................ 9-2
All Refrigerator Pro Wiring Diagram ......................... 9-3

Basic Information
1-4
Important Safety Instructions
Safety Precautions
Do not attempt to install, operate or service the unit until
you have read the safety precautions in this manual.
Safety items throughout this manual are labeled with a
Danger, Warning, or Caution based on the risk type.
Definitions
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible
injury or death.
General Safety
• Do not store or use gasoline or other flammable
liquids near this or any other appliance. Read
product labels for warnings regarding flammability
and other hazards.
• Do not operate the unit in the presence of explosive
fumes.
• Avoid contact with any moving parts of the automatic
ice maker.
• Remove all staples from the carton to avoid injury.
Staples can also damage finishes if they come in
contact with other appliances or furniture.
Child Safety
Packing Materials:
• Packing cartons covered with rugs, bedspreads,
plastic sheets, or stretch wrap may become airtight
chambers and can quickly cause suffocation.
• Destroy or recycle the product’s carton, plastic bags,
and any other exterior wrapping material immediately
after the refrigerator is unpacked. Children should
never play with these items.
Child Entrapment and Suffocation:
• These problems are not limited to the past.
Whether junked, abandoned, or temporarily stored
(even for a few hours), unattended refrigerators and
freezers are dangerous. Please take the precautions
listed below.
Proper Disposal of Refrigerators/Freezers
Electrolux Home Products Inc. strongly encourages
responsible appliance recycling/disposal methods.
Check with your utility company or visit
www.recyclemyoldfridge.com for more information
on recycling your old refrigerator.
Before you recycle or dispose of your old refrigerator/
freezer:
• Remove the doors.
• Leave the shelves and baskets in place so children
may not easily climb inside.
• Have refrigerant and compressor oil removed by a
qualified service technician.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
Indicates installation, operation, or maintenance
information which is important but not hazard
related.

Basic Information
1-5
Major Appliance Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will repair or
replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used, and
maintained in accordance with the provided instructions. In addition, the cabinet liner and sealed refrigeration system (compressor,
condenser, evaporator, dryer or tubing) of your appliance is covered by a two through five year limited warranty. During the 2nd
through 5th years from your original date of purchase, Electrolux will repair or replace any parts in the cabinet liner and sea led
refrigeration system which prove to be defective in materials or workmanship when such appliance is installed, used, and
maintained in accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary
household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are
not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or
other cosmetic parts.
11. Pickup and delivery costs; your appliance is designed to be repaired in the home.
12. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or
mileage expense for service calls to remote areas, including the state of Alaska.
13. Damages to the finish of appliance or home incurred during transportation or installation, including but not limited to floors,
cabinets, walls, etc.
14. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux
parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse,
inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE REPAIR OR REPLACEMENT AS
PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT
NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH
AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED
WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED
WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS.YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be
required. If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be
obtained by contacting Electrolux at the addresses or phone numbers below.
This warranty only applies in the USA, Puerto Rico and Canada. In the USA and Puerto Rico, your appliance is warranted by
Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by
Electrolux Canada Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for
service and parts under this warranty must be performed by Electrolux or an authorized service company. Product features or
specifications as described or illustrated are subject to change without notice.
USA
1-877-435-3287
Electrolux Major Appliances North America
P.O. Box 212378
Augusta, GA 30907
Canada
1-800-265-8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada L5V 3E4

Basic Information
1-6
Model Number Breakdown
Serial Number Breakdown
All Refrigerator Specifications

1-7
Basic Information
Understanding Features and Terms - All Refrigerator Professional
Series
Electrolux refrigerators are designed for optimal convenience and storage flexibility. The illustration below is
provided to assist you with familiarizing yourself with product features and terminology.
NOTE: Features may vary according to model.

1-8
Basic Information
®
All Freezer Specifications

1-9
Basic Information
Understanding Features and Terms - All Freezer Professional Series
Electrolux freezer are designed for optimal convenience and storage flexibility. The illustration below is
provided to assist you with familiarizing yourself with product features and terminology.
NOTE: Features may vary according to model.

1-10
Basic Information
Notes

2-1
Installation Information
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY WHEN USING AN ICON ALL FREEZER
AND/OR ALL REFRIGERATOR, FOLLOW BASIC SAFETY PRECAUTIONS INCLUDING THE FOLLOWING:
- READ ALL INSTRUCTIONS BEFORE OPERATING THE FREEZER AND/OR REFRIGERATOR.
- BEFORE PERFORMING ANY TYPE OF SERVICE OR INSTALLATION, MAKE SURE THAT ELECTRIC
POWER TO THE FREEZER AND/OR REFRIGERATOR IS DISCONNECTED.
- TO AVOID THE POSSIBILITY OF EXPLOSION OR FIRE, DO NOT STORE OR USE COMBUSTIBLE,
FLAMMABLE, OR EXPLOSIVE LIQUIDS OR VAPORS (SUCH AS GASOLINE) INSIDE OR IN THE VICINITY
OF THIS OR ANY OTHER APPLIANCE.
- THIS APPLIANCE IS EQUIPPED WITH A THREE-PRONG GROUNDING PLUG FOR PROTECTION
AGAINST POSSIBLE ELECTRIC SHOCK HAZARDS. PLUG IT ONLY INTO A DEDICATED, GROUNDED
ELECTRICAL OUTLET. WHEN ONLY A STANDARD TWO-PRONG ELECTRICAL OUTLET IS AVAILABLE,
THE CUSTOMER MUST HAVE IT REPLACED WITH A DEDICATED, PROPERLY GROUNDED THREE-
PRONG ELECTRICAL OUTLET BEFORE USING THIS APPLIANCE.
- DO NOT UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE
POWER CORD.
DO NOT USE AN ADAPTER PLUG.
DO NOT USE AN EXTENSION CORD.
DO NOT USE A POWER CORD THAT IS FRAYED OR DAMAGED.
THE USE OF A GROUND FAULT INTERRUPTER (GFI) IS NOT RECOMMENDED.
- DO NOT INSTALL OR USE A DAMAGED APPLIANCE. IF YOU RECEIVE A DAMAGED APPLIANCE,
IMMEDIATELY CONTACT YOUR DEALER OR BUILDER.
- THE INSTALLER MUST SHOW THE CUSTOMER THE LOCATION OF THE POWER PLUG SO THAT THEY
KNOW WHERE AND HOW TO DISCONNECT POWER TO THE FREEZER AND/OR REFRIGERATOR.
- DO NOT INSTALL, REPAIR, OR REPLACE ANY PART OF THE FREEZER AND/OR REFRIGERATOR
UNLESS SPECIFICALLY RECOMMENDED IN THE LITERATURE ACCOMPANYING IT. A QUALIFIED
SERVICE TECHNICIAN SHOULD PERFORM ALL OTHER SERVICE.
Electrolux Home Products Inc. cannot be held responsible for damage to property or injury to persons
caused by failure to comply with the installation, maintenance and safety instructions contained in this
Service Manual.
Recognize safety symbols, words and labels:
Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type as described
below:
This symbol alerts you to situations that may cause serious body harm, death or
property damage.
This symbol alerts you to situations that may cause bodily injury or property damage.

Installation Information
2-2
DESTROY CARTON, PLASTIC BAGS, AND ANY EXTERIOR WRAPPING MATERIAL IMMEDIATELY AFTER
THE REFRIGERATOR/FREEZER IS UNPACKED. CHILDREN SHOULD NEVER USE THESE ITEMS FOR
PLAY. CARTONS COVERED WITH RUGS, BEDSPREADS, PLASTIC SHEETS OR STRETCH WRAP MAY
BECOME AIR TIGHT CHAMBERS AND CAN QUICKLY CAUSE SUFFOCATION.
A CHILD MIGHT SUFFOCATE IF THEY CRAWL INTO THE UNIT TO HIDE OR PLAY. REMOVE THE DOOR/
LID OF THE REFRIGERATOR/FREEZER WHEN NOT IN USE, EVEN IF YOU PLAN TO DISCARD THE UNIT.
MANY COMMUNITIES HAVE LAWS REQUIRING YOU TO TAKE THIS SAFETY PRECAUTION.
REMOVE OR DISCARD ANY SPACERS USED TO SECURE THE SHELVES DURING SHIPPING. SMALL
OBJECTS ARE A CHOKE HAZARD TO CHILDREN.
CHILD ENTRAPMENT AND SUFFOCATION ARE NOT PROBLEMS OF THE PAST. JUNKED OR
ABANDONED REFRIGERATORS OR FREEZERS ARE STILL DANGEROUS– EVEN IF THEY WILL SIT FOR
“JUST A FEW DAYS”. IF YOU ARE GETTING RID OF YOUR OLD REFRIGERATOR OR FREEZER, PLEASE
FOLLOW THE INSTRUCTIONS BELOW TO HELP PREVENT ACCIDENTS:
• REMOVE THE DOOR/LID.
• LEAVE SHELVES IN PLACE SO CHILDREN MAY NOT EASILY CLIMB INSIDE.
• HAVE THE REFRIGERANT REMOVED BY A QUALIFIED TECHNICIAN.
Doors
Handles are secure and tight
Door seals completely to cabinet on all sides
Doors are level across the top
Leveling
Unit is level, side-to-side and tilted 1/4” (6mm)
front-to-back
Toe grille is properly attached to the unit frame
Cabinet is setting solid on all corners
Electrical Power
House power turned on
Unit is plugged in
Ice Maker
House water supply connected to water valve
No water leaks present at all connections -
recheck in 24 hours
Ice maker is turned ON
Front filter must be flush with filter housing
(select models)
Final Checks
Shipping material removed
Fresh food and freezer temperatures set
Crisper humidity controls set
Registration card sent in
Installation Checklist

Installation Information
2-3
Location
1. Choose a place that is near a grounded electrical
outlet. Do Not use an extension cord or an adapter
plug.
2. If possible, place unit(s) out of direct sunlight and
away from range, dishwasher or other heat sources.
3. The unit(s) must be installed on a floor that is level
and strong enough to support a fully loaded unit(s).
4. Consider water supply availability for models
equipped with an automatic ice maker.
5. The unit(s) should be located where surrounding
temperature will not exceed 110ºF (43ºC) or drop
below 40°F (5°C).
6. For ease of installation, proper air circulation and
electrical connections, see Figure 2-1 for
recommended clearances.
7. DO NOT block the toe grille on the lower front of
the unit. Sufficient air circulation is essential for the
proper operation of the unit(s).
Figure 2-1. Installation Clearances
The exterior walls of the refrigerator/freezer may
become quite warm as the compressor works to
transfer heat from the inside. Temperatures as much
as 30°F warmer than room temperatures can be
expected.
If your refrigerator and/or freezer is placed with the
door hinge side against a wall, you may have to allow
additional space so the door can be opened wider.
Leveling
The freezer and/or refrigerator must have all bottom
corners resting firmly on a solid floor. The floor must be
strong enough to support a fully loaded freezer and/or
refrigerator.
It is VERY IMPORTANT for your freezer and/or
refrigerator to be level in order to function properly. If
the unit is not leveled during installation, the door/lid may
be misaligned and not close or seal properly, causing
cooling, frost or moisture problems.
After discarding crating screws and wood base, use a
carpenter’s level to level the unit from front to back.
Adjust the plastic leveling feet in front, ½ bubble higher,
so that the door closes easily when left half way open. Figure 2-2. Leveling Unit

Installation Information
2-4
Electrical Information
These guidelines must be followed to ensure that safety
mechanisms in the design of the unit will operate
properly.
Refer to the serial plate for correct electrical rating. The
power cord of the unit is equipped with at three-prong
grounding plug for protection against shock hazards. It
must be plugged directly in to its own properly grounded
three-prong receptacle, protected with a 15 amp time
delay fuse or circuit breaker. The receptacle must be
installed in accordance with the current edition of the
National Electrical Code (NFPA 70) the local codes and
ordinances. Consult a qualified electrician. Receptacles
with Ground Fault Circuit Interrupters (GFCI) are NOT
RECOMMENDED. DO NOT USE AN EXTENSION
CORD OR AN ADAPTER PLUG.
Figure 2-3. Electrical Receptacle
Avoid fire hazard or electric shock. Do not use an
extension cord or an adapter plug. Do not remove
any prong from the power cord.
Never unplug the freezer by pulling on the power
cord. Always grip the plug firmly and pull straight
out from the receptacle.
Turning the control to “OFF” turns off the
compressor but does not disconnect power to
other electrical components.
Leveling Instructions For All
Refrigerator/Freezer Pairs
• Remove two leg levelers provided in literature bag.
While unit is lying on its back for wood skid removal,
install both leg levelers in rear of unit.
• Level door of first unit using all four levelers and
slide unit into place. Recheck for levelness and
adjust if necessary.
• Measure distance from floor to bottom of door on
first unit. Adjust and level second unit so door height
matches.
• Leg Level Adjustments:
• One full turn of all four leg levelers will raise door
5/32”.
• One full turn of both front leg levelers will raise door
3/16” and tilt top of door back 7/16”.
• One full turn of both rear leg levelers will lower door
1/32” and tilt top of door forward 7/16”.
• One full turn of both side leg levelers will raise door
3/16” and tilt top of door 3/8”.
• Slide second unit into place leaving a minimum gap
of 3/16” between units for door swing clearance.
• This last step may require at least one extraction of
the second unit to properly align units in a “built-in”
application.
If the voltage varies by 10% or more, freezer and/or
refrigerator performance may be affected. Operating any
unit with insufficient power can damage the motor. Such
damage is not covered under the warranty. If you suspect
your voltage is high or low, consult your power company
for testing.
To prevent the freezer from being turned off accidentally,
do not plug the unit in to an outlet controlled by a wall
switch or pull cord. Do not pinch, knot, or bend the power
cord in any manner.

Installation Information
2-5
Cut-Out Dimensions
1. Minimum opening of 66” High x 33” Wide x 25-1/4”
Deep is required for a single-unit “Built-In Look”
installation. 66” Wide is required for double-unit
installation. (66” High to be measured from finished
floor to underside of soffit or overhead cabinet.)
2. Minimum 25-1/4” depth requires recessed electrical
outlet and copper water line.
3. Remove all wall / floor molding prior to built-in
installation.
4. When installing a unit adjacent to wall, cabinet or
other appliance that extends beyond front edge
of unit, 20” minimum clearance is recommended
to allow for optimum 140° door swing, providing
complete crisper access and removal. (Absolute
4” minimum clearance will ONLY allow for 90° door
swing which will provide limited crisper access with
restricted removal.)
5. Water line for ice maker can enter opening through
floor or rear wall. Copper tubing is recommended
between cold water line and water connection
location. Recommended water line tubing is 48”
minimum length by 1/4” diameter. Installation
of easily accessible shutoff valve in water line is
required.
6. To allow for ease of moving out side-by-side units
after installation, 84” minimum length of coiled
copper tubing recommended.
7. If optional Single or Double Trim Kit is to be used,
different cutout dimensions are required.
Optional Accessories
Single All-Freezer Kit (SFRRSRKIT)
Single All-Refrigerator Kit (SRRRSRKIT)
Double All-Freezer/All-Refrigerator Kit (DUORSRKIT)*
*Louvered Trim Kit (DUORSRKIT) is NOT compatible for
installation with panel-ready models.
Single Louvered Trim Kit (SRRRSRKIT)
For single All-Refrigerator installation. Includes louvered
top grille and vented, louvered toe kick, 4” riser with
leveling system and side / top trim pieces.
Double Louvered Trim Kit (DUORSRKIT)
For All-Freezer/ All-Refrigerator side-by-side installation.
Includes full-width, louvered top grille and vented,
louvered toe kick, two 4” risers with leveling systems and
side / top trim pieces.
Figure 2-5. All Refrigerator Unit Cut-out
Figure 2-4. All Freezer Unit Cut-out
Figure 2-6. Trim Kits

Installation Information
2-6
Water Supply
The ice maker (if equipped) requires a permanent water
supply to function correctly. During installation, establish
this water supply by connecting a copper tube from the
household water system to a valve at the rear of the unit.
Requirements:
• Access to a cold water line with pressure of 20-120
psi. (System supplied with cold water only.)
• Copper tubing with ¼ inch (6.4mm) Outside
Diameter (OD). Length is the distance from the rear
of the unit to your household water supply line, plus
seven (7) feet (2.1 meters).
• A shut-off valve for the connection between your
household water line and the refrigerator supply line.
DO NOT use a self-piercing shut-off valve.
• A compression nut and ferrule (sleeve) for the water
supply connection at the water valve inlet.
To connect the water supply to the rear of the unit
(See Figure 2-7 and 2-8a):
1. Ensure that the unit is unplugged.
2. Flush the supply line until water is clear by placing
the end of the copper tube in a sink or bucket and
opening the shut-off valve. Close shut-off valve
when flushing is complete.
3. Remove and discard the plastic cap from the water
valve inlet at the rear of the unit.
4. Slide the brass compression nut, then the ferrule
(sleeve) onto the copper tube.
5. Push the copper tube into the water valve inlet as far
as it will go (¼ inch or 6.4mm).
6. Slide the ferrule (sleeve) into the water valve and
finger-tighten the compression nut onto the valve.
Tighten another half turn with a wrench but DO NOT
over-tighten.
Figure 2-8a. Water Valve Connection
To avoid property damage:
• Use copper tubing for the water supply line
(plastic tubing is more likely to leak).
Manufacturer is not responsible for any
damage if plastic tubing is used for supply line.
• Ensure water supply and installation comply
with state and local laws and regulations.
• DO NOT install water supply tubing where
temperatures fall below freezing.
• Chemicals from a malfunctioning softener
can damage the ice maker. If the ice maker is
connected to soft water, ensure that the softener
is maintained and working properly.
Water line kit number 5303917950, available from the
appliance dealer at additional cost, contains 25 feet
(7.6 meters) of 1/4” OD copper tubing, a saddle type
shut-off valve (non piercing), (2) 1/4” brass compres-
sion nuts, (2) ferrules/sleeves, and instructions for
installing a water supply line.
Figure 2-7. Water Connection
Ice Maker Water Supply Hookup
For All-Freezer/All-Refrigerator Side-by-Side Installation
All
Freezer
Water Filter
Ice Maker
Connection
Note: For single-unit installation,
direct plumbing to ice maker recommended.
Water Inlet
All
Refrigerator
Connection

Installation Information
2-7
Figure 2-8b. Water Valves
The water valve on the left is the old style threaded
outlet connection. The water valve on the right has
the push-type outlet fitting.
7. Secure the copper tube to the units’ rear panel with
a steel clamp and screw.
8. Coil the excess copper tubing (about 2½ turns)
behind the unit as shown. Arrange coiled tubing to
avoid vibration or wear against other surfaces.
9. Open water supply shut-off valve and tighten any
connections that leak.
10. Connect unit to home power supply.
11. To turn ice maker On, lower wire signal arm. (See
ice maker front cover for On/Off position of arm.
Connecting the Water Valve to
the Ice Maker
For models Serial Number WB92254219 and greater built
after June 1, 2009, the units will have a different water
valve than earlier production models. The new water
valves have a quick connect outlet fitting which takes a
standard .255 diameter plastic tube. The old style of
water valves required a flanged tube and a threaded nut
to make the water connection. (See Figure 2-8b)
Water Line Kit PN 297114101 will still be used to make
the water line connections between the new style water
valve and ice maker, however the flanged tube will have
to be modified as described in the steps below:
1. Using a box cutters or knife, cut the pointed end
from the water line just below the raised point. Be
sure to cut straight across the water line. Do not
leave open/cut end at an angle. (See Figure 2-8c)
2. Remove the cut end and plastic nut from the water
line and discard.
3. Measure 11/16” from the end of the water line and
place a mark on the line with a permenent marker.
4. Insert the modified water line into the push-type
fitting on the new valve, making sure that the water
line is pushed in up to the mark.
5. Inspect for leaks once water supply is turned on.
Figure 2-7. Water Connection
Figure 2-8c. Cut along dotted line to modify tubing.

Installation Information
2-8
Trim And Riser Kit Installation
Instructions
The Dual Trim and Riser Kit consists of the following:
• Riser Kit - 2 packages
• Hardware Kit - 1 bag
• Trim Kit - 1 package
• Installation Instructions
The Single Trim and Riser Kit consists of the following:
• Riser Kit - 2 packages
• Hardware Kit - 1 bag
• Trim Kit - 1 package
• Installation Instructions
Before starting installation, have the following tools on
hand:
• PhillipsTM Screwdriver
• Shims - Wooden or Plastic
• Tape Measure (min. 7” length)
• Safety Glasses
• Tape (Duct or Masking)
• Carpenter’s Level
• Drill & 1/8” Bit
• 1/2” Socket Wrench
The following items should be with the collar kit option:
Figure 2-9. Trim Kit Components
Before You Begin
• Be careful when unpacking components. Do not use
sharp objects when removing packaging material.
This may scratch the surface of trim components.
• Make sure there is a large, clear area of floor
(approx. 10’ by 8’) to assemble the trim kit. Place a
drop cloth over the floor to prevent scratching of the
trim kit and/or floor.
• Use extreme care when handling the metal trim
pieces. Corners are very sharp and easily damaged
if dropped.