DO NOT REMOVE this label until the refrigerator has been leveled.
Please follow all instructions for leveling your refrigerator.
P/N: 242046601
2
1
6
Doors
Handles are secure and tight
Door seals completely to cabinet on all sides
Fresh food doors are level
Leveling
Refrigerator is level, side to side and tilted
¼ inch (6 mm) front to back
Toe grille is properly attached to refrigerator
Cabinet is sitting solid on all corners
Electrical Power
House power turned on
Refrigerator plugged in
Installation Check List
Preparing For Installation
CAUTION
Room temperatures below
55°F (13°C) or above
110°F (43°C) will impair
cooling ability of your
refrigerator’s compressor.
NOTE
If you need to remove the doors to get your refrigerator into the house, please refer to “Removing Doors”
in the Use & Care Guide. These installation instructions are provided only as a possible customer option.
Electrolux recommends that you use a service or kitchen contracting professional to install your refrigerator.
IMPORTANT
If you are installing your refrigerator
without connecting it to a water
supply, make sure the ice maker’s
power switch is turned Off (see the
Use & Care Guide for more details).
WARNING
To avoid electric shock, which can cause death or severe personal injury, do not connect your
refrigerator to an electrical power source until you have completed Step 2 of these instructions.
Be sure to coordinate site preparation and installation with your kitchen
contractor.
Include these minimum guidelines in your site preparation:
• Chooseaplacenearagroundedelectricaloutlet.
• Donotuseanextensioncordoranadapterplug.
• Avoiddirectsunlightandcloseproximitytoarange,dishwasheror
other heat source.
• Floorshouldbelevelandabletosupportafullyloadedrefrigerator.
• Therefrigerator’sIceDispenserrequires
water supply access.
• Planforeasyaccesstocountertopswhen
removing food.
• Forcompleteaccesstodrawersandfreezer
baskets, doors must be able to fully open.
• Loadrefrigeratorfromsideofcabinetonly.
• Donotrunretainingstrapsoverhandlesnorovertightenstraps.
• Neveruserefrigeratorhandlestomovetherefrigerator.
Allowthefollowingclearancesforeaseofinstallation,properaircirculation,and
plumbing and electrical connections: Sides & Top: 3/8inch / Rear: 1 inch
NOTE
Please call 1-877-435-3287 if
you need assistance with this
installation.
CAUTION
• Shiftingtherefrigeratorfromsidetosidemay
damage flooring.
• Donotblockthetoegrilleonthelowerfrontofyour
refrigerator. Sufficient air circulation is essential
for proper operation.
LevelRefrigerator&AdjustDoors(ifnecessary)
5
Electrolux uses packing foam and tape to secure the internal parts of your refrigerator for
shipping. Once the refrigerator is in position, you can remove this material.
What’s Next?
Congratulations! You are ready to begin enjoying your new Electrolux refrigerator.
• Forimportantsafetyinstructionsandtolearnhowtooperateyourrefrigerator,pleaseread
the entire Use & Care Guide.
• Youmaywanttostartwiththe“NormalOperatingSights&Sounds”sectionoftheGuideto
learn what to expect during typical operation.
• Pleaseregisteryourproduct.Youcanregisteronlineatwww.electroluxappliances.com.or
you can simply send in the Registration Card.
Guidelines for final positioning of your refrigerator
• Allfourcornersofthecabinetmustrestrmlyontheoor.
• Thesidesshouldtilt¼inch(6mm)fromfronttoback
(to ensure that doors close and seal properly).
• Doorsshouldalignwitheachotherandbelevel.
Most of these conditions can be met by raising or lowering
the adjustable front rollers.
To level the cabinet using the front rollers:
1 You can raise or lower each door. Use a 3/8inch socket
wrench to turn the adjustment screws (1 per side).
To raise: turn adjustment screw clockwise.
To lower: turn adjustment screw counterclockwise.
2 Ensure both doors are bind-free with their seals
touching the cabinet on all four sides and that cabinet is
stable.
3 Afterunitisleveled,loweranti-tipleguntilitcontacts
theoor.
To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Placeendofwatersupplylineintosinkorbucket.
TurnONwatersupplyandushsupplylineuntil
waterisclear.TurnOFFwatersupplyatshutoffvalve.
3. Remove plastic cap from water valve inlet and
discard cap.
4. If you use copper tubing - Slide brass compression
nut, then ferrule (sleeve) onto water supply line.
Pushwatersupplylineintowatervalveinletasfar
asitwillgo(¼inch).Slideferrule(sleeve)intovalve
inletandngertightencompressionnutontovalve.
Tightenanotherhalfturnwithawrench;DONOT
overtighten. See Figure 1.
If you use stainless steel tubing - The nut and
ferrule are already assembled on the tubing. Slide
compressionnutontovalveinletandngertighten
compression nut onto valve. Tighten another half turn
withawrench;DONOTovertighten.See Figure 2.
5. With steel clamp and screw, secure water supply line
(copper tubing only) to rear panel of refrigerator as
shown.
6. Coilexcesswatersupplyline(coppertubingonly),
about 2½ turns, behind refrigerator as shown and
arrange coils so they do not vibrate or wear against
any other surface.
7. TurnONwatersupplyatshutoffvalveandtightenany
connections that leak.
8. Reconnect refrigerator to electrical power source.
9. Toturnicemakeron,lowerwiresignalarm(freezer
ice maker) or set the ice maker’s On/Off power switch
tothe“ON”position(freshfoodicemaker).
Before Installing The Water Supply Line, You Will Need:
• BasicTools:adjustablewrench,at-bladescrewdriver,
andPhillipsTM screwdriver
• Accesstoahouseholdcoldwaterlinewithwater
pressure between 30 and 100 psi.
• Awatersupplylinemadeof¼inch(6mm)OD,copper
or stainless steel tubing. To determine the length of
tubing needed, measure the distance from the ice maker
inlet valve at the back of the refrigerator to your cold
water pipe. Then add approximately 7 feet, so the refrigerator can be moved out for cleaning.
• Ashutoffvalvetoconnectthewatersupplylinetoyourhouseholdwatersystem.DONOTuseaself-
piercing type shutoff valve.
• Acompressionnutandferrule(sleeve)forconnectingacopperwatersupplylinetotheicemakerinletvalve.
WARNING
To avoid electric shock, which can
cause death or severe personal in-
jury, disconnect the refrigerator from
electrical power before connecting a
water supply line to the refrigerator.
CAUTION
ToAvoidPropertyDamage:
• CopperorStainlessSteelbraidedtubingisrecommendedforthewatersupplyline.
Water supply tubing made of ¼ inch (6 mm) plastic is not recommended to be used.
Plastic tubing greatly increases the potential for water leaks, and the manufacturer
will not be responsible for any damage if plastic tubing is used for the supply line.
• Donotreusecompressionfittingorreusethreadsealtape.
• DONOTinstallwatersupplytubinginareaswheretemperaturesfallbelowfreezing.
• Chemicalsfromamalfunctioningsoftenercandamagetheicemaker.Iftheicemakeris
connected to soft water, ensure that the softener is maintained and working properly.
NOTE
Check with your local building authority for
recommendations on water lines and associated
materials prior to installing your new refrigerator.
Depending on your local/state building codes, Electrolux
recommends for homes with existing valves its Smart
Choice®waterlinekit5305513409(witha6ft.Stainless
SteelWaterLine)andforhomeswithoutanexisting
valve, Electrolux recommends its Smart Choice water®
linekit5305510264(witha20ft.CopperWaterLine
withself-tappingsaddlevalve).Pleaserefertowww.
electroluxappliances.com for more information.
Copper water line
from household water supply
(Includeenough tubing in loop to allow
moving refrigerator out for cleaning.)
Ferrule
(Sleeve)
Copper
water line
WaterValve
Valve Inlet
Water Valve
Bracket
Steel
Clamp
Plastic Water Tubing
to Ice Maker
Fill Tube Brass
Compression
Nut
Figure 1
Figure 2
*Please refer to your Use & Care Guide for more details.
Connect Water Supply
Ice Maker
House water supply connected to
refrigerator
Nowaterleakspresentatallconnections
IceMakeristurnedON.
Final Checks
Shippingmaterialremoved
Fresh Food and Freezer temperatures set
3
Raise
Lower
Anti-tip
Leg
Door
Door
If you are not satisfied with the installation of your refrigerator, please contact the store where you purchased it or call 1-877-435-3287 for assistance.
NOTE
DONOTremovecenterscrewfromfreezer
drawer. This is a factory adjustment.
Remove Hex
Head Drawer
Screw
Remove Hex
Head Drawer
Screw
Do Not Remove
Other Screws
Remove Hex
Head Drawer
Screw
Remove Hex
Head Drawer
Screw
Do Not Remove
Other Screws
Leveling Freezer Drawer (if necessary)
1. Check gasket seal around top,
bottom, and sides of freezer drawer.
2. If gasket is not sealed, open drawer
and slightly loosen 4 drawer screws
(2 on each side) to allow drawer to
rotate.
3. Close drawer and recheck the seal
on the gasket (A). Open the drawer
grabbing by the sides in the center
(B). Be careful not to rotate the
drawer.
4. Tighten 4 drawer screws.
5. Recheck gasket seal.
6. Install the toe grille by fitting into
place.
Raising/Lowering Door
Remove Screw
Open
Door
90
degrees
Bottom of Door
A
B
Remove Screw
Doors final adjustment using the adjustable lower hinge (select models, if
necessary):
1Open doors to 90 degrees.
2Remove screw.
3Lift the door while adjusting the washer.
To raise the door: rotate washer clockwise.
To lower the door: rotate washer counterclockwise.
4 Replacethescrew,ensuringitisbetweenthespokesofthehingewasher.Screwwillnotbe
tight, just insert until it is flush with the hinge.
NOTE
If after adjusting doors higher the door
makes a popping/clicking sound, remove
screw and replace with the longer one
provided.
Pull Drawer Out
From Both Sides
Grab Drawer
At Center
Then
Push Against
Freezer Drawer
AB
4
Remove Internal Shipping Materials
Installation Instructions* for French Door Bottom Freezer/Refrigerator
