Electrolux EWFLW65H - 27'' Front-Load Washer Operating manual

Publication #5995523544 Revision B August 2010
Technical Service Manual
Wave-Touch™ & IQ-Touch™
Front-Load Washer
Models
EWFLW65H & EIFLW55H

Basic Information
1-1
Safe Servicing Practices For All Appliances
Avoid personal injury and/or property damage by observing important Safe Servicing Practices.
Following are some limited examples of safe practices:
1. DO NOT attempt a product repair if you have any doubts as to your ability to complete the repair in a safe and
satisfactory manner.
2. Always use the correct Replacement Parts as indicated in the parts documentation. Substitutions may defeat
compliance with Safety Standards Set For Home Appliances. Do not exceed maximum recommended wattage
on light bulb replacements. Doing so could blow fuses and/or damage transformers.
3. Before servicing or moving an appliance:
• Remove power cord from the electrical outlet, trip circuit breaker to the OFF position, or remove fuse.
• Turn off water supply if applicable.
4. Never interfere with the proper operation of any safety device.
5. Use ONLY REPLACEMENT PARTS CATALOGED FOR THIS APPLIANCE. Substitutions may defeat
compliance with Safety Standards Set For Home Appliances.
6. GROUNDING: The standard color coding for safety ground wires is GREEN, or GREEN with YELLOW
STRIPES. Ground leads are not to be used as current carrying conductors. It is EXTREMELY important that
the service technician reestablish all safety grounds prior to completion of service. Failure to do so will create
a hazard.
7. Prior to returning the product to service, ensure that:
• All electrical connections are correct and secure.
• All electrical leads are properly dressed and secured away from sharp edges, high-temperature components,
and moving parts.
• All non-insulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal
parts and panels.
• All safety grounds (both internal and external) are correctly and securely connected.
• All panels are properly and securely reassembled.
• Gas and water supplies are turned ON if shut off prior to service.
© 2010 Electrolux Home Products, Inc.
ATTENTION!!!
This service manual is intended for use by persons having electrical and mechanical training and a level
of knowledge of these subjects generally considered acceptable in the appliance repair trade. Electrolux
Home Products, Inc. cannot be responsible, nor assume any liability, for injury or damage of any kind
arising from the use of this manual.

Basic Information
Table of Contents
1-2
Section 1 - Basic Information........................................ 1-1
Safe Servicing Practices For All Appliances ................... 1-1
Table of Contents............................................................. 1-2
Important Safety Instructions............................................ 1-3
Protect Children................................................................ 1-4
Prevent Fire...................................................................... 1-4
Prevent Injury ................................................................... 1-4
Model and Serial Number Breakdown ............................. 1-4
Product Specifications...................................................... 1-5
Prevent Injury and Damage To Washer........................... 1-6
Automatic Temperature Control (ATC) System ............... 1-6
Water Level ...................................................................... 1-6
Installation Cycle .............................................................. 1-6
Component Description.................................................... 1-7
Door Lock Assembly Operation ....................................... 1-7
Electronic Water Level Switch.......................................... 1-7
Mass Damper Operation .................................................. 1-8
Drive Motor Operation...................................................... 1-8
Speed Control .................................................................. 1-8
Automatic Dispenser Operation ....................................... 1-9
Unbalance Sensing .......................................................... 1-10
Oversudsing Detection ..................................................... 1-11
The Language of Laundry ................................................ 1-11
Section 2 - Installation Information .............................. 2-1
Important Safety Instructions............................................ 2-1
Safety Precautions ........................................................... 2-1
Tools and Materials Needed for Installation..................... 2-2
Electrical System Requirements ...................................... 2-3
Grounding Requirements ................................................. 2-3
Water Supply Requirements ............................................ 2-4
Drain System Requirements ............................................ 2-4
Removing Foam Packaging ............................................. 2-4
Clearance Requirements.................................................. 2-5
Installation in a Recess or Closet..................................... 2-5
Installed Washer Dimensions........................................... 2-6
Removing Shipping Hardware.......................................... 2-7
Leveling Washer............................................................... 2-8
Connecting Inlet Water..................................................... 2-8
Connecting Drain and Electrical....................................... 2-9
Wave-Touch™ Installation Cycle ..................................... 2-10
IQ -Touch™ Installation Cycle ......................................... 2-10
Reversing Door ................................................................ 2-11
Preparing to Reverse Door Swing .............................. 2-11
Removing Trim Ring ................................................... 2-11
Removing Door from Hinge ........................................ 2-11
Removing Hinge from Front Panel ............................. 2-12
Removing Door Lock from Front Panel ...................... 2-12
Reattaching Door Lock to Front Panel ....................... 2-13
Reattaching Hinge to Front Panel............................... 2-13
Removing Striker Plate ............................................... 2-14
Removing Latch Indicator ........................................... 2-14
Removing Hole Plug ................................................... 2-15
Reinserting Latch Indicator ......................................... 2-15
Reattaching Striker Plate ............................................ 2-16
Reinserting Hole Plug ................................................. 2-16
Reattaching Door Assembly ....................................... 2-16
Reversing Trim Ring ................................................... 2-17
Reinstalling Trim Ring................................................. 2-17
Reinstalling Trim Plug................................................. 2-17
Accessories ...................................................................... 2-18
Matching Storage Pedestal......................................... 2-18
Dryer Stacking Kit ....................................................... 2-18
Drain Hose Extension Kit............................................ 2-18
Universal Appliance Wrench....................................... 2-18
Dryer Stacking Instructions .............................................. 2-19
Kit Components .......................................................... 2-19
Preparing Dryer for Stacking ...................................... 2-19
Prepare Top Surface of Washer ...................................... 2-20
Stacking Dryer.................................................................. 2-20
Removing Stacked Dryer ................................................. 2-21
Section 3 - Electronic Control....................................... 3-1
Control Panel Wave-Touch™........................................... 3-1
Selecting the Appropriate Cycle and Settings
Overview........................................................................... 3-1
Demo Mode Wave Touch ................................................ 3-1
Wave-Touch™ Washer Cycle Chart ................................ 3-2
Control Panel IQ-Touch™................................................ 3-3
Selecting the Appropriate Cycle and Settings
Overview........................................................................... 3-3
Demo Mode IQ Touch...................................................... 3-3
IQ-Touch™ Washer Cycle Chart ..................................... 3-4
Cycle Selection................................................................. 3-5
Normal......................................................................... 3-5
Colors.......................................................................... 3-5
Whites ......................................................................... 3-5
Heavy Duty ................................................................. 3-5
Deep Clean Sanitize ................................................... 3-6
Casual......................................................................... 3-6
Active Wear................................................................. 3-6
Fast Wash................................................................... 3-6
Delicate ....................................................................... 3-7
Hand Wash ................................................................. 3-7
Spin Only .................................................................... 3-7
My Favorite (IQ Touch™) ........................................... 3-7
My Favorites (Wave Touch)........................................ 3-7
Wave Touch™ Washing/Rinsing Temperature .......... 3-9
Spin Speed ................................................................. 3-10
Soil Level .................................................................... 3-10
IQ Touch™ Washing/Rinsing Temperature................ 3-10
Options ............................................................................. 3-11
Eco Friendly ................................................................ 3-11
Stain Clean ................................................................. 3-11
Extra Rinse ................................................................. 3-11
Auto Temp .................................................................. 3-11
Continuous Wash Mode.............................................. 3-12
Extra Spin ................................................................... 3-12
Prewash ...................................................................... 3-12
Warm Rinse ................................................................ 3-12
Delay Start .................................................................. 3-12
User Interface Features.................................................... 3-13
Save as Favorite......................................................... 3-13
Set Prefs ..................................................................... 3-13
User Guides ................................................................ 3-13
Stain Guides ............................................................... 3-13
Control Lock................................................................ 3-13
Save as Favorite......................................................... 3-14
Setting Preferences.......................................................... 3-15
Custom Mode.............................................................. 3-15
System Clean.............................................................. 3-15
Reset (WaveTouch™) ................................................ 3-16
Reset (IQTouch™)...................................................... 3-16

Basic Information
1-3
Contrast........................................................................ 3-16
Brightness .................................................................... 3-17
Volume......................................................................... 3-17
Language ..................................................................... 3-17
Cycle Description ......................................................... 3-17
Status Display .............................................................. 3-17
Install Cycle (WaveTouch™)............................................. 3-18
Install Cycle (IQ Touch™) ................................................. 3-18
Diagnostics and Error Codes ............................................ 3-19
Reading Error Codes......................................................... 3-19
To Clear Latest Stored Error Code ................................... 3-19
Diagnostic Test.................................................................. 3-20
To Start the Diagnostic Test ........................................ 3-20
Exiting Diagnostic Mode .............................................. 3-20
Error Code Chart............................................................... 3-21
Error Code Test Chart....................................................... 3-22
Section 4- Component Teardown .................................. 4-1
Warnings and Cautions..................................................... 4-1
Door Components ............................................................. 4-2
Door Trim Ring .......................................................... 4-2
Door Assembly ............................................................ 4-2
Striker Plate ................................................................ 4-3
Inner Door Glass.......................................................... 4-3
Latch Indicator ............................................................. 4-3
Outer Door Glass......................................................... 4-4
Door Hinge .................................................................. 4-4
Door Lock Assembly.................................................... 4-5
Bellows .............................................................................. 4-5
Reinstalling or Replacing the Bellows............................... 4-6
Interior Light ...................................................................... 4-7
Top Panel .......................................................................... 4-7
Vibration Dampener .......................................................... 4-7
Detergent Drawer Removal and Breakdown..................... 4-8
Console Panel ................................................................... 4-8
Control Assembly Removal and Breakdown..................... 4-9
Front Panel........................................................................ 4-10
Controller Assembly .......................................................... 4-10
Weight Ring....................................................................... 4-11
Water Inlet / Overflow Vent Tube Grommet...................... 4-11
Overflow /Vent Tube.......................................................... 4-12
Water Inlet Valve Assembly .............................................. 4-12
Water Inlet Screen............................................................. 4-13
Top Rear Brace................................................................. 4-13
External Drain Hose .......................................................... 4-13
Detergent Cavity Assembly............................................... 4-14
Detergent Dispenser Outlet Hose ..................................... 4-14
Power Cord ....................................................................... 4-15
Rear Access Cover ........................................................... 4-15
Suspension Spring ............................................................ 4-15
Top Center Brace.............................................................. 4-16
Electric Water Level Sensor.............................................. 4-16
Drain Pump ....................................................................... 4-16
Drive Belt........................................................................... 4-17
Large Pulley ...................................................................... 4-17
Drive Motor........................................................................ 4-17
Speed Control Board Assembly ........................................ 4-18
Air Bell ............................................................................... 4-18
Heating Element................................................................ 4-19
Air Shock Absorber ........................................................... 4-19
Tub Assembly.................................................................... 4-20
Section 5- Troubleshooting.............................................. 5-1
Troubleshooting Chart......................................................... 5-1
Component Resistance Chart ............................................. 5-5
Section 6- Wiring Diagrams ............................................. 6-1
Wiring Diagram Models
EWFLW65H & EIFLW55H .................................................. 6-1
Important Safety Instructions
Safety Precautions
Do not attempt to install, operate or service the unit until
you have read the safety precautions in this manual.
Safety items throughout this manual are labeled with a
Danger, Warning, or Caution based on the risk type.
Definitions
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible
injury or death.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
Indicates installation, operation, or maintenance
information which is important but not hazard
related.

1-4
Basic Information
Protect Children
• Do not allow children to play on or in the washer.
Close supervision of children is necessary when the
washer is used near children. As children grow,
teach them the proper, safe use of all appliances.
• Destroy the carton, plastic bag and other packing
materials after the washer is unpacked. Children
might use them for play. Cartons covered with rugs,
bedspreads or plastic sheets can become airtight
chambers.
• Keep laundry products out of children’s reach.
To prevent personal injury, observe all warnings on
product labels.
• Before the washer is removed from service or
discarded, remove the washer door to prevent
accidental entrapment.
• Failure to comply with these warnings could result in
serious personal injuries.
Prevent Fire
• Do not wash items that have been previously
cleaned in, soaked in, or spotted with gasoline,
cleaning solvents, kerosene, cooking oils, waxes,
etc. Do not store these items on or near the washer.
These substances give off vapors or chemical
reactions that could ignite or explode.
• Do not put oily or greasy rags or clothing on top of
the washer. These substances give off vapors that
could ignite the materials.
• Do not add gasoline, cleaning solvents, or other
flammable or explosive substances to the wash
water. These substances give off vapors that could
ignite or explode.
• Under certain conditions, hydrogen gas may
be produced in a hot water system that has not been
used for 2 weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before
using the washer, turn on all hot water faucets and
let the water flow from each for several minutes.
This will release any accumulated hydrogen gas.
Hydrogen gas is flammable; do not smoke or use an
open flame during this time.
• Do not store or use gasoline or other flammable
vapors or liquids in the vicinity of this or any other
appliance.
• Failure to comply with these warnings could result in
fire, explosion, serious bodily injury and/or damage
to the rubber or plastic parts of the washer.
Prevent Injury
• To prevent shock hazard and assure stability during
operation, the washer must be instaled and
electrically grounded by a qualified service person in
accordance with local codes. Installation instructions
are packed in the washer for installer’s reference.
Refer to INSTALLATION INSTRUCTIONS for
detailed grounding procedures. If the washer is
moved to a new location, have it checked and
reinstalled by a qualified service person.
• To prevent personal injury or damage to the washer,
the electrical power cord of the washer must be
plugged into a properly grounded and polarized
3-prong outlet. The third grounding prong must never
be removed. Never ground the washer to a gas pipe.
Do not use an extension cord or an adapter plug.
• Follow package directions when using laundry
products. Incorrect usage can produce poisonous
gas resulting in serious injury or death.
• Do not combine laundry products for use in 1load
unless specified on the label.
• Do not mix chlorine bleach with ammonia or acids
such as vinegar.
Model Number Breakdown
Each model follows the following nomenclature:
E ................. for Electrolux
I .................. for IQ Touch
W ................. for Wave Touch
FLW ............. for Front Load Washer
ED ............... for Electric Dryer
GD ............... for Gas Dryer
MED/MGD .... Steam Electric/Steam Gas Dryer
P ................... for Pedestal
Serial Number Breakdown

Basic Information
1-5
Product Specifications
IQ-Touch™ Washer
White and 1 Premium Color
Smooth Glide on Drawers & Dispenser
Largest Capacity (4.7 cu.ft. IEC)
Push2Open: Door, Dispenser, Pedestal
Inclined Axis with 1200 RPM
Electrolux Blue LEDs
Custom Cycles Including My Favorite
Intelligent and Adaptive LCD Controls
Quiet (52-72 dBA) and Low Vibration
Best in Class Vibration and 2nd Floor Installation Ready
11 cycles with My Favorite and NSF Sanitary
ATC with Heater, 5 Soil Levels, 5 Temps and 5 Spin
Speeds, 14 Hour Delay Start
CEE Tier 3 for Super Efficient Appliances
Fastest Cycle Time
Cycles
NSF Certified Deep Clean Sanitize
Heavy Duty
Whites
Colors
Normal
Casual – Use for Permanent press items
Quick Wash – Fastest cycle in the industry
Delicates – Gentler than any cycle available
Hand Wash
Spin Only
My Favorite – Programmable by consumer
Additional Options
Up to 14 hour delay start – use this to save $ by running
in off peak energy demand hours
Control Lock – to prevent accidental operation by children
5 Temperature Selections
5 Spin Speed Selections
3 Soil Level Selections
ATC – Automatic Temperature Control
Product Specifications
Wave-Touch™ Washer
2 Premium Colors
Enhanced LCD Controls with larger trilingual
display
1350 RPM
Quiet (52-72 dBA)
Multiple User Mode – 3 User Modes with Favorite and
Custom Cycles
11 Standard + 3 Favorite Cycles with custom settings to
reach 42 Total Cycles
Enhanced ATC Control with on/off selection
22 hour delay start
Drum Light with Manual Switch
More efficient with Higher MEF
Fastest Cycle Time
Cycles
NSF Certified Deep Clean Sanitize
Heavy Duty
Whites
Colors
Normal
Active Wear – Use for sports/workout gear
Casual – Use for permanent press items
Quick Wash – Fastest cycle in the industry
Delicates – Gentler than any cycle available
Hand Wash
Spin Only
My Favorites – 3 favorites Programmable by consumer
Additional Options
Up to 22 hour delay start – use this to save $ by running
in off peak energy demand hours
Automatic Control Lock – to prevent accidental operation
by children
5 Temperature Selections
6 Spin Speed Selections
4 Soil Level Selections
ATC – Automatic Temperature Control with additional
heater

1-6
Basic Information
Prevent Injury And Damage To The Washer
• All repairs and servicing must be performed by an authorized servicer unless specifically recommended in the
Use & Care Guide. Use only authorized factory parts.
• Do not tamper with controls.
• Do not install or store the washer where it will be exposed to the weather.
• Do not install on carpet. Install washer on a solid floor. It may be necessary to reinforce the floor to prevent
vibration or movement.
• To reduce the risk of electric shock, disconnect this appliance from the power supply before attempting any user
maintenance. Turning the controls to the OFF position does not disconnect this appliance from the power supply.
• To prevent injury, do not reach into the washer while parts are moving. Before loading, unloading or adding
items, push in the cycle selector knob and allow the drum to coast to a complete stop before reaching inside.
• This washer is equipped with an electrical overload protector. The motor will stop if it becomes overheated.
The washer will automatically restart after a cool down period of up to 30 minutes, if the washer has not been
manually turned off during this time.
• Failure to comply with these warnings could result in serious personal injuries.
Automatic Temperature Control (ATC) System
This method of temperature control uses a thermistor input from the drum water Negative Temperature Coefficient
Thermistor to sense the water temperature in the drum. It also controls the amount of hot water used for a given fill
and temperature selection.
The following are the temperature ranges for the wash/rinse cycles:
Temperature Setting Temperature Range
Sanitize 67°C (152°F) +/- 5°C
Hot 55°C (131°F) +/- 5°C
Eco Hot 45°C (113°F) +/- 5°C
Warm 29°C (84°F) +/- 4°C
Eco Warm 27°C (81°F) +/- 3°C
Warm Rinse 24°C (75°F) +/- 3°C
Cold 15°C (59°F) +/- 5°C
Water Level
The spinner tub vanes must not be in water during this check.
Check is taken at the back and center of the washgroup. Water Pressure must be between 20 and 120 P.S.I.
Installation Cycle
This cycle checks the basic functionality of the unit. It also verifies that the water hoses have been hooked up
properly, hot to hot and cold to cold. To verify that the hoses have been hooked up properly, the unit turns on
the hot water valve until the water reaches 130 mm (5.11 inches) in height. The temperature in the drum has to
increase from ambient to a specified value for the algorithm to recognize the water lines have been properly hooked
up. If the temperature doesn’t increase to the specified value either within the 130 mm fill level or a given amount
of time, the “CHECK HOSES” warning will be displayed, the machine will drop out of the install cycle and drain what
water has accumulated. When this happens verify that the hoses were properly connected and if they have been,
then push the Cancel button (clears the message) and the unit is ready for use.
If water remains in the unit after following the procedure above, move the cycle knob to the Drain Spin Cycle and
drain the rest of the water from the tub. When the drum starts moving, the water has been completely drained and
the cycle can then be cancelled.
Water Height In
Drum
1.75 +/- 0.5 In.
4.45 +/-1.27cm
All Models

1-7
Basic Information
Component Description
Door Lock Assembly Operation
The door lock has a push push mechanism that is either
in the latched position, where the strike is in the cam, or
an unlatched position, where the strike is not in the cam.
When in the locked position, the user can push the Start/
Pause button which activates a solenoid causing the door
to lock. When the Start/ Pause button or Cancel button
is pushed, the solenoid is activated again causing the
door to unlock. The solenoid does not require a constant
current, but only an impulse to lock or unlock. If the door
lock is locked when the power goes out, there is a manual
override switch in the back of the door lock assembly to
unlock the door lock. When the door lock assembly is
mounted in the front panel on the right (when facing the
front panel) the manual override switch lever would need
to be pulled up, and when assembled on the left, the lever
would be pushed down.
There is a child entrapment safety feature that allows a
child to push from the inside of the unit with less than 15
pounds of force and the door will open, but only when the
door is unlocked.
When in the unlatched position, there is one electrical
and two mechanical features that prevent the door lock
from being able to lock.
Electronic Water Level Switch
The electronic water level sensor is mounted to the right
side panel under the top of the washer and controls the
water level in the washer.
The electronic water level sensor is made up of an
electronic board and a bellow inside a sealed chamber.
The chamber is connected by a hose to the air bell
located at the bottom of the washer attached to the
drain boot. The electronic board reads the pressure in
the bellow and converts it into an electronic signal. This
signal is then sent to the control board which governs the
incoming water by connecting or disconnecting a neutral
line to the water solenoids.
Manual Override
Lever For Door Lock
Bottom of
Wash Tub
Electronic Water
Level Sensor
Air Bell
Drain Boot
Hose
Electronic Water Level Sensor Components
Door Lock Manual Override Lever

1-8
Basic Information
Mass Damper Operation
The mass damper is a simple assembly consisting of
a heavy mass supported by gel. This device reduces
cabinet vibration through the dissipation of energy
coming from “gel” deformation. The use of the mass
damper is effective for a wide range of drum speeds and
installation conditions.
Drive Motor Operation
The motor is an induction, three phase AC motor that
varies speeds when the voltage from the speed control
board varies in frequency and amount. The motor has a
tachogenerator that inputs the speed of the motor to the
speed control board.
Speed Control
The speed control board is mounted to the base plate
of the washer in the left rear corner of the washer. The
speed control board controls the following operations:
1. The speed of the drive motor is controlled by
converting input line to neutral single phase 60
Hertz voltage, to a varying frequency, three phase
output voltage from zero to 300 VAC. By varying the
amount, frequency, and polarity of the voltage and
comparing the input from the tachogenerator on the
drive motor, the speed control board can operate the
drive motor at a preprogrammed speed and
direction.
2. The balance of the load in the washer is monitored
during the spin cycle by converting the sine wave
from the tachogenerator to square waves and
comparing the distance between the square waves.
If this distance exceeds a specified parameter, the
wash load is determined to be unbalanced and the
washer responds accordingly.
Concrete
Mass Damper
Mass Damper Mounted on Unit
Mass Damper Cross Section

1-9
Basic Information
Dispenser Flow Pattern
Automatic Dispenser Operation
The automatic dispenser for the detergent, liquid bleach
and fabric softener system is made up of the dispenser
cavity, and a removable drawer with four cavities: one
for pre-wash, one for detergent, one for bleach and one
for fabric softener. A plastic conveyer is snapped to the
bottom of the drawer to direct the outputs from the bleach
and softener chambers to the dispenser housing outlet
channel. This prevents the mixtures from coming out the
front of the drawer.
The 3 outlets of the water inlet valve assembly are
inserted into the rear of the automatic dispenser. During
the fill cycles, water is directed into the top of the cavity
through 3 inlets. The inlet on the right, as viewed from
the front of the washer, is connected to the combination
output of the hot water solenoid and the center cold water
solenoid.
The left and middle inlet, as viewed from the front of the
washer, are connected to the cold water solenoid.
In the fill cycle, water enters into the top of cavity and is
directed across the top of the cavity by 5 channels: the
dispenser advanced rinsing technology channel, the
pre-wash channel (cold water only), the detergent
channel, bleach channel and the fabric softener channel.
The channel that receives the water is determined by
which inlet supplies the water or if both inlets supply the
water.
The dispenser advanced rinsing technology channel
receives water whenever the inlet on the right, as viewed
from the front of the washer, is activated. This path
allows the water to bypass the dispenser drawer and
enter the tub by the advanced rinsing technology hose
connected between the cavity and the bellows.
The pre-wash dispenser channel receives water from the
left-hand input, as viewed from the front of the washer.
The pre-wash channel forms a loop that allows the
water to pass over the pre-wash detergent section of the
drawer.
As the water passes over the pre-wash detergent section,
holes in the cavity allows some of the water to enter and
flush the pre-wash detergent cavity. Since the flow of the
incoming water is more than the holes can dispense, the
excess water backs up into a channel across the rear
of the dispenser. Water in this channel and the mixture
from the detergent drawer flow into the tub through the
large hose at the rear of the dispenser.
The detergent dispenser channel receives water from the
right-hand input, as viewed from the front of the washer.
The detergent channel forms a loop that allows the water
to pass over the detergent section of the drawer. As the
water passes over the detergent section, holes in the
cavity allow some of the water to enter and flush the
detergent cavity. Since the flow of incoming water is
more than the holes can dispense, the excess water
backs up into a channel across the rear of the dispenser.
Water in this channel and the mixture from the detergent
drawer flow into the tub through the large hose at the rear
of the dispenser.
Detergent is dispensed at the start of the cycle, but
bleach and fabric softener are not dispensed until later in
the cycle. The bleach and softener cavities in the drawer
have tubes molded into the bottom of them.
These tubes allow bleach or fabric softener to be added
to their cavity without being dispensed as long as the
liquid is below the top of the tubes. At the proper time
in the cycle when bleach or fabric softener is to be
dispensed, water is added to the cavity. This raises the
mixture above the top of the tube and the bleach or fabric
softener starts flowing into the tub.
Main Wash
Detergent
Channel
Pre-Wash
Detergent
Channel
To ART
Hose
Bleach
Channel
Fabric
Softener
Channel

1-10
Basic Information
To allow the cavities to empty, the cover of the detergent
drawer cover has tubes molded into it that fit over the
tubes in the cavities.
These tubes are larger than the tubes in the cavity and
are designed to fit over the tubes, but not touch the
bottom of the cavity when the cover is installed. When
water is added to either the bleach or fabric softener
liquid, the mixture level rises between the tubes above
the tubes in the cavity and flows into the washer tub.
Since the end of the tube on the insert does not touch the
bottom of the cavity, a siphoning action will occur when
the solenoid activates and allows water into the cavity.
The added water creates an “overfill” condition and starts
the siphoning. The cavity will empty itself when the water
is turned off by the solenoid.
The bleach dispenser channel receives water from the
middle input, as viewed from the front of the washer. The
bleach channel forms a path that allows the water to pass
over the bleach cavity section of the cavity.
As the water passes over the bleach section, holes in the
cavity allow some of the water to enter and mix with the
bleach. This raises the mixture level above the tubes in
the drawer bleach cavity allowing the mixture to flow into
the tub.
Like the detergent channel, the flow of the incoming water
is more than the holes can dispense, allowing the excess
water to back up into the channel across the rear of the
dispenser and flow into the tub. For water to enter the
fabric softener channel, both the middle and right inlets
must be activated. As water from the left inlet passes over
the channel, it collides with the water from the right inlet.
This collision changes the water path directing it to the
front of the cavity and into the fabric softener channel.
The fabric softener channel forms a loop that allows the
water to pass over the fabric softener cavity section of the
drawer.
As the water passes over the fabric softener section,
holes in the cavity allow some of the water to enter and
mix with the fabric softener.
This raises the mixture level above the tubes in the
drawer fabric softener cavity allowing the mixture to flow
into the tub. Like the detergent channel, the flow of the
incoming water is more than the holes can dispense
allowing the the excess water to backup into the channel
across the rear of the dispenser and flow into the tub.
Bleach and Fabric Softener Flow Tubes
An available option is for a liquid detergent cup that is
placed within the main wash compartment. This allows
for the liquid detergent to be dispensed at the proper
time, and allows the liquid detergent to be poured and
held during a delay start or held during the pre-wash.
The drawer front has a button that when pushed,
releases a latch that secures the drawer in the unit.
When the latch is released, a spring in the dispenser
housing assembly pushes the drawer partially open. The
drawer can then be pulled open to pour additives into
the drawer. The drawer is then pushed back into place
and the latch on the drawer front assembly latches to the
conso le to keep the dispenser closed.
Unbalance Sensing
This algorithm determines the amount of either static
unbalance (point unbalance) or dynamic unbalance (two
points of unbalance that are equal and opposite each
other in the drum) in the unit. When distributing the load
the unit monitors the point unbalance until it drops below
a set threshold. When this happens the machine speeds
up to 120 RPM and verifies that the load unbalance is
ready to spin. If the point unbalance is low enough to
allow spin, the unit will accelerate to 250 RPM from 120
RPM, during which time it monitors the dynamic
unbalance. If this unbalance is high enough, the spin
will terminate and the algorithm will proceed to try and
rebalance the load.
Cover Tube
Cavity Tube

1-11
Basic Information
Oversudsing Detection
Oversudsing is detected after the wash cycle by two methods.
1. Suds are detected when torque is very high and the pressure can not be drawn down to zero at the drain pump.
The spin cycle is then skipped, and a slower rinse agitation is performed with longer pauses and less time in
agitation, and the fabric softener is moved from the last rinse cycle to the second rinse cycle. If suds are still
detected after the first rinse, or after the wash cycle for a Fast Cycle, up to 3 rinse cycles are added to clear the
suds.
2. Suds are detected when the machine tries to spin and the pressure goes above a given threshold, and when the
drum speed is reduced back down to 120 RPM the pressure does not go back to zero within a given amount of
time. The drum will then stop (0 RPM) and sit for 30 seconds with the drain pump off. The drain pump will then
turn on for one minute and attempt to drain the tub of water and/or suds. If pressure can not be brought to zero
and this happens twice in a given intermediate rinse cycle, then the spin cycle is skipped and if it is the second
intermediate spin (first for the Fast Cycle) then up to 3 rinse cycles will be added to eliminate suds in the tub.
The Language of Laundry
Machine Wash
Instructions
Special
Care
Bleaching
Instructions
Dryer
Instructions
Ironing
Instructions
Dry
Cleaning
Bleach
as Needed
Non-chlorine
Bleach as Needed
DO NOT
Bleach
Hand
Wash
DO NOT
Wring
Normal
Wash
Permanent
Press
Gentle
Cycle
DO NOT
Machine Wash
Cold
(<85ºF)
Warm
(<105ºF)
Hot
(<120ºF)
Hot
(<140ºF)
Low Heat
Med. Heat
High Heat
DO NOT
Steam
DO NOT
Iron
Dry Clean
Dry Clean
w/ Any
Solvent
Dry Clean
w/Petroleum
Solvent
Dry Clean
w/Solvents
Other Than
Trichloroethylene
DO NOT
Dry Clean
DO NOT
Machine Dry
Line Dry
Drip Dry
Dry Flat
Dry in
Shade
Normal
Dry
Permanent
Press
Gentle
Setting
DO NOT
Tumble Dry
No Heat
Low Heat
Normal/
Med. Heat
High
Heat

1-12
Basic Information
Notes

2-1
Installation Information
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY WHEN USING A WAVE-TOUCH™
OR IQ-TOUCH™ FRONT-LOAD WASHER, FOLLOW BASIC SAFETY PRECAUTIONS INCLUDING THE
FOLLOWING:
- READ ALL INSTRUCTIONS BEFORE OPERATING THE WASHER.
- BEFORE PERFORMING ANY TYPE OF SERVICE OR INSTALLATION, MAKE SURE THAT ELECTRIC
POWER TO THE WASHER IS DISCONNECTED.
- TO AVOID THE POSSIBILITY OF EXPLOSION OR FIRE, DO NOT STORE OR USE COMBUSTIBLE,
FLAMMABLE, OR EXPLOSIVE LIQUIDS OR VAPORS (SUCH AS GASOLINE) INSIDE OR IN THE
VICINITY OF THIS OR ANY OTHER APPLIANCE.
- THIS APPLIANCE IS EQUIPPED WITH A THREE-PRONG GROUNDING PLUG FOR PROTECTION
AGAINST POSSIBLE ELECTRIC SHOCK HAZARDS. PLUG IT ONLY INTO A DEDICATED,
GROUNDED ELECTRICAL OUTLET. WHEN ONLY A STANDARD TWO-PRONG ELECTRICAL
OUTLET IS AVAILABLE, THE CUSTOMER MUST HAVE IT REPLACED WITH A DEDICATED,
PROPERLY GROUNDED THREE-PRONG ELECTRICAL OUTLET BEFORE USING THIS APPLIANCE.
DO NOT UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM
THE POWER CORD. DO NOT USE AN ADAPTER PLUG. DO NOT USE AN EXTENSION CORD. DO
NOT USE A POWER CORD THAT IS FRAYED OR DAMAGED. THE USE OF A GROUND FAULT
INTERRUPTER (GFI) IS NOT RECOMMENDED.
- DO NOT INSTALL OR USE A DAMAGED APPLIANCE. IF YOU RECEIVE A DAMAGED APPLIANCE,
IMMEDIATELY CONTACT YOUR DEALER OR BUILDER.
- DO NOT USE THE WASHER UNTIL IT HAS BEEN PROPERLY INSTALLED BY A QUALIFIED
INSTALLER ACCORDING TO THESE INSTALLATION INSTRUCTIONS. THE INSTALLER MUST
SHOW THE CUSTOMER THE LOCATION OF THE POWER PLUG SO THAT THEY KNOW WHERE
AND HOW TO DISCONNECT POWER TO THE WASHER.
- DO NOT INSTALL, REPAIR, OR REPLACE ANY PART OF THE WASHER UNLESS SPECIFICALLY
RECOMMENDED IN THE LITERATURE ACCOMPANYING IT. A QUALIFIED SERVICE TECHNICIAN
SHOULD PERFORM ALL OTHER SERVICE.
Electrolux Home Products Inc. cannot be held responsible for damage to property or injury to persons
caused by failure to comply with the installation, maintenance and safety instructions contained in this
Service Manual.
Recognize safety symbols, words and labels:
Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type as described
below:
This symbol alerts you to situations that may cause serious body harm, death or
property damage.
This symbol alerts you to situations that may cause bodily injury or property damage.
Safety Precautions
Do not attempt to install or operate this appliance until you read the safety precautions in this guide. Safety items
throughout this guide are labeled with a Warning or Caution based on the risk type.

Installation Information
2-2
DESTROY CARTON, PLASTIC BAGS, AND ANY EXTERIOR WRAPPING MATERIAL IMMEDIATELY
AFTER THE DRYER IS UNPACKED. CHILDREN SHOULD NEVER USE THESE ITEMS FOR PLAY.
CARTONS COVERED WITH RUGS, BEDSPREADS, PLASTIC SHEETS OR STRETCH WRAP MAY
BECOME AIR TIGHT CHAMBERS AND CAN QUICKLY CAUSE SUFFOCATION.
KEEP LAUNDRY PRODUCTS OUT OF CHILDREN’S REACH. TO PREVENT PERSONAL INJURY,
OBSERVE ALL WARNINGS ON PRODUCT LABELS.
CUT HAZARD. TO PREVENT SERIOUS INJURY FROM SHARP EDGES, WEAR WORK GLOVES
WHEN HANDLING, UNPACKING OR DISASSEMBLING UNIT.
EXCESSIVE WEIGHT HAZARD
To avoid back or other injury, have more than one person move or lift the dryer.
The electrical service to the dryer must conform with local codes and ordinances and the latest
edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical code
C22.1 part 1.
Pre-installation Requirements
Tools and materials needed for installation:

Installation Information
2-3
Electrical Requirements
Circuit - Individual, properly polarized and grounded 15
amp. branch circuit fused with 15 amp. time delay fuse
or circuit breaker.
Power Supply - 2 wire, with ground, 120 volt single
phase, 60 Hz alternating current.
Outlet Receptacle - Properly grounded 3-prong
receptacle to be located so the power supply cord is
accessible when the washer is in an installed position.
Grounding Requirements
1. The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electrical shock by a path of least resistance
for electrical current.
2. Since your washer is equipped with a power supply
cord having an equipment-grounding conductor
and a grounding plug, the plug MUST be plugged
into an appropriate, copper wired receptacle that is
properly installed and grounded in accordance with
all local codes and ordinances or in the absence of
local codes, with the National Electrical Codes,
ANSI/NFPA 70 (latest edition). If in doubt, call a
licensed electrician. DO NOT cut off or alter the
grounding prong on the power supply cord. In
situations where a two-slot receptacle is present,
it is the owner’s responsibility to have a licensed
electrician replace it with a properly grounded three
prong grounding type receptacle.
Grounding Type
Wall Receptacle
Power Cord with
3- Prong Grounded Plug
DO NOT, under any
circumstances, cut,
remove, or bypass the
grounding plug.
Figure 2-1
Because of potentially inconsistent voltage
capabilities, the use of this washer with power
created by gas powered generators, solar powered
generators, wind powered generators or any other
generator other than the local utility company is
not recommended.
GFI (Ground Fault Interrupter) receptacle is not
required.
IMPROPER CONNECTION OF THE EQUIPMENT
GROUNDING CONDUCTOR CAN RESULT IN A
RISK OF ELECTRICAL SHOCK. CHECK WITH A
LICENSED ELECTRICIAN IF YOU ARE IN DOUBT
AS TO WHETHER THE APPLIANCE IS PROPERLY
GROUNDED.

Installation Information
2-4
Water Supply Requirements
Hot and cold water faucets MUST be installed within 42
inches (107 cm) of the washer’s water inlet. The faucets
MUST be 3/4 inch (1.9 cm) with threading for laundry
hose connection. Water pressure MUST be between 30
and 120 psi. Pressure difference between hot and cold
cannot be more than 10 psi. The local water department
can advise the customer of the line water pressure.
Drain System Requirements
1. Drain capable of eliminating 17 gals (64.3 L)
per minute.
2. A standpipe diameter of 1-1/4 in. (3.18 cm)
minimum.
3. The standpipe height above the floor should be:
Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244 cm)
Removing Foam Packaging
1. Temporarily remove door tape.
2. Open washer door and remove everything from the
drum.
3. Close door and reapply door tape.
4. Using a rug, blanket or piece of cardboard to protect
the floor, carefully lay washer on it’s back.
5. Remove styrofoam base and shipping plug and set
them aside.
6. Carefully return washer to an upright position.
7. Carefully move the washer to within 4 feet (1m) of its
final location.
Figure 2-2. Standpipe Dimensions
Figure 2-3. Unpacking Unit
Drain hose attached to the washer can reach a 79
in. (201 cm) high standpipe. For higher standpipe,
use hose P/N 137098000.
EXCESSIVE WEIGHT HAZARD
To avoid back or other injury, have more than one
person move or lift the washer.
Save styrofoam base and shipping plug for use
to help prevent washer damage during any future
moves.

Installation Information
2-5
Clearance Requirements
Installation in a Recess or Closet
If washer and dryer are installed in the same closet,
door ventilation is required: A minimum of 120 square
inches (774.2 cm²) of opening, equally divided at the top
and bottom of the door, is required. Louvered openings
should be located 3 inches (7.6 cm) from bottom and top
of door. Air openings are required to be unobstructed
when a door is installed. A louvered door with equivalent
air openings for the full length of door is acceptable.
Figure 2-4. Closet Installation
Figure 2-5. Clearances
DO NOT INSTALL THE WASHER:
1. In an area exposed to dripping water or outside
weather conditions. The ambient temperature
should never be below 60°F (15.6° C) to
maximize detergent effectiveness.
2. In an area (garage or garage-type building)
where gasoline or other flammables (including
automobiles) are kept or stored.
3. Floor MUST be solid with a maximum slope
of 1 inch (2.54 cm). To minimize vibration or
movement, reinforcement of the floor may be
necessary.

Installation Information
2-6
Installed Washer Dimensions