Electrolux EWS 1230 User manual

WASHING MACHINE
TVÄTTMASKIN
PYYKINPESUKONE
STIRALWNAÅ MAfiINA
INSTRUCTION BOOKLET
BRUKSANVISNING
KÄYTTÖOHJE
RUKOVODSTVO PO ÈKSPLUATACII
EWS 1030
132 990 762
EWS 1230
S
FIN
RUS
GB
132990761 copertina 19-04-2004 10:34 Pagina 1

2
Dear customer,
Please read these operating instructions carefully
and pay particular attention to the safety notes
indicated in the first pages. We recommend that you
keep this instruction booklet for future reference and
pass it on to any future owners.
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly
important for your safety or correct functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of
the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
Our contribution to the protection of the
environment: we use environmentally
friendly paper.
Transport damages
When unpacking the appliance, check that it is not
damaged. If in doubt, do not use it and contact the
Service Centre.
Contents
Warnings 3
Disposal 4
Tips for environmental protection 4
Technical specifications 4
Installation 5
Unpacking 5
Positioning 5
Water inlet 5
Water drainage 6
Electrical connection 6
Your new washing machine 7
Description of the appliance 7
Detergent dispenser drawer 7
Use 8
Control panel 8
Controls 8-11
Programme information 12
Washing hints 13-14
Sorting the laundry 13
Temperatures 13
Before loading the laundry 13
Maximum loads 13
Laundry weights 13
Removing stains 13
Detergents and additives 14
Operating sequence 15-16
International wash code symbols 17
Washing programmes 18
Special programmes 19
Maintenance 20
Bodywork 20
Detergent dispenser drawer 20
Drain filter 20
Water inlet filter 21
Emergency emptying out 21
Frost precautions 21
Something not working? 22-23
132990762 GB.qxd 14/12/2004 10.32 Pagina 2

ENGLISH
3
Installation
• All internal packing must be removed before using
the appliance. Serious damage may be caused to
the machine or adjacent furniture if the protective
transit devices are not removed or are not
completely removed. Refer to the relevant
paragraph in the instruction book.
• Any electrical work required to install this appliance
must be carried out by a qualified electrician.
• Any plumbing work required to install this
appliance must be carried out by a qualified
plumber.
• After having installed the machine, check that it is
not standing on its electrical supply cable.
• If the appliance is placed on a carpeted floor,
ensure that air can circulate freely between the
feet and the floor.
Use
• This appliance is designed for domestic use. It
must not be used for purposes other than those for
which it was designed.
• Only wash fabrics which are designed to be
machine washed. Follow the instructions on each
garment label.
• Do not overload the appliance. Follow the
instructions in the instruction book.
• Make sure that all pockets are empty. Objects such
as coins, safety pins, pins and screws can cause
extensive damage.
• Do not machine wash garments saturated with
petroleum, methylated spirits, trichlorethylene, etc.
If such fluids have been used to remove stains
prior to washing, wait until they have completely
evaporated from the fabric before placing
garments in the appliance.
• Place small items such as socks, belts, etc. in a
cloth bag or pillowcase to prevent them getting
trapped between the drum and the tub.
Warnings
• Use only the recommended quantities of fabric
softener. An excessive amount could damage the
laundry.
• Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the door
seal and prevents the formation of musty smells.
• Always check that water has emptied out before
opening the door. If not, drain the water following
the instructions in the instruction book.
• Always unplug the appliance and shut the water
tap after use.
General safety
• Repairs to the machine must be carried out only by
qualified personnel. Repairs carried out by
inexperienced persons could cause serious
danger. Contact your local Service Centre.
• Never pull the power supply cable to remove the
plug from the socket; always take hold of the plug
itself.
• During high temperature wash programmes the
door glass may get hot. Do not touch it!
Child safety
• Children are often not aware of how dangerous
electrical appliances can be. When the machine is
working, children should be carefully supervised
and not be allowed to play with the appliance.
• The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children - danger
of suffocation! Keep them out of children’s reach.
• Keep all detergents in a safe place out of children’s
reach.
• Make sure that children or pets do not climb into
the drum.
• When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with
the remaining cable. Disable the door catch in
order to prevent children from becoming trapped
inside while playing.
The following warnings are provided in the interests of overall safety. You must read them carefully before
installing or using the appliance.
132990762 GB.qxd 14/12/2004 10.32 Pagina 3

DIMENSIONS Height 85 cm
Width 60 cm
Depth 42 cm
MAXIMUM LOAD Cotton 4 kg
Synthetics 1.5 kg
Delicates 1.5 kg
Woollens 1 kg
SPIN SPEED 1000 rpm max. (EWS 1030)
1200 rpm max. (EWS 1230)
POWER SUPPLY VOLTAGE/FREQUENCY 220-230 V/50 Hz
TOTAL POWER ABSORBED 2200 W
MINIMUM FUSE PROTECTION 10 A
WATER PRESSURE Minimum 0,05 MPa
Maximum 0,8 MPa
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility.
Technical specifications
4
Disposal
Tips for environmental protection
Packaging materials
The materials marked with the symbol are
recyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
Machine
Use authorised disposal sites for your old appliance.
Help to keep your country tidy!
To save water, energy and to help protect the
environment, we recommend that you follow these
tips:
• Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
• The machine works more economically if it is fully
loaded.
• With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
• Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
132990762 GB.qxd 14/12/2004 10.32 Pagina 4

ENGLISH
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Using a spanner, unscrew and remove the two
rear bottom screws. Slide out the two plastic pins.
2. Lay the machine on its back, taking care not to
squash the hoses. This can be avoided by
placing one of the corner packing pieces between
the machine and the floor.
3. Remove the polystyrene block from the bottom of
the machine and release the two plastic bags.
4. Very carefully slide out the left polythene bag,
removing it towards the right and then
downwards.
5. Very carefully slide out the right polythene bag,
removing it towards the left and then upwards.
6. Set the machine upright and remove the
remaining rear screw. Slide out the relevant pin.
P1127
P1126
P1124
2
3
1
P0001
P1129
7. Plug all the holes with the plugs which you will
find in the envelope containing the instruction
booklet.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that the
machine does not touch the wall or other kitchen
units.
Carefully level by screwing the adjustable feet in or
out. Never place cardboard, wood or similar
materials under the machine to compensate for any
unevenness in the floor.
Water inlet
Connect the water inlet hose to a tap with a 3/4"
thread.
Do not use already employed hoses for water
connection.
Important!
Before connecting up the machine to new pipework
or to pipework that has not been used for some time,
run off a reasonable amount of water to flush out any
debris that may have collected in the pipes.
P1088
P1051
P0002
P1128
Installation
5
132990762 GB.qxd 14/12/2004 10.32 Pagina 5

The other end of the inlet hose which connects to the
machine can be turned in any direction. Simply
loosen the fitting, rotate the hose and retighten the
fitting, making sure there are no water leaks
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially
designed for this type of use.
Water drainage
The end of the drain hose can be positioned in three
ways:
Hooked over the edge of a sink using the plastic
hose guide supplied with the machine. In this
case, make sure the end cannot come unhooked
when the machine is emptying.
This could be done by tying it to the tap with a piece
of string or attaching it to the wall.
In a sink drain pipe branch. This branch must be
above the trap so that the bend is at least 60 cm
above the ground.
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain pipe
must be larger than the outside diameter of the drain
hose.
P0022
P0021
The drain hose must not be kinked.
For a correct functioning of the machine the
drain hose must remain hooked on the proper
support piece situated on the top part of the back
side of the appliance.
Electrical connection
This machine is designed to operate on a 220-230 V,
single-phase, 50 Hz supply.
Check that your domestic electrical installation can
take the maximum load required (2.2 kW), also
taking into account any other appliances in use.
Connect the machine to an earthed socket.
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution.
Should the appliance power supply cable
need to be replaced, this should be carried
out by our Service Centre.
Please ensure that when the appliance is
installed the power supply cable is easily
accessible.
P1118
6
132990762 GB.qxd 14/12/2004 10.32 Pagina 6

ENGLISH
Your new washing machine
7
This new machine meets all modern requirements for effective treatment of laundry with low water, energy and
detergent consumption.
•The automatic cooling of the washing water from 95° to 60°C before draining will prevent old drain pipes
from being deformed.
•The special wool programme with its new delicate wash system treats your woolens with extreme care.
•The unbalance detection device prevents vibration during spinning.
•The ECO valve allows total use of detergent and reduces water consumption so saving energy.
•The programme selector dial combines the function of programme and temperature selection, making it
easier to set the programme.
1 Detergent dispenser drawer and programme chart
2 Control panel
3 Door handle
4 Drain pump
5 Adjustable feet
Detergent dispenser drawer
Prewash
Main wash
Fabric softener, starch
Description of the appliance
4
3
5
12
TIMELINE
1000
900
700
500
EWS 1030
+
P1017
132990762 GB.qxd 14/12/2004 10.32 Pagina 7

8
Use
123 4 567891011
12
13 14
900
700
500
TIMELINE
+
1000
EWS 1030
Control panel
1 Programme chart
A programme chart in English is in the interior part of
the detergent dispenser drawer or together with the
instruction booklet..
2 Mains-on light
This light comes on when the ON/OFF button is
pressed, and goes out when it is pressed again.
3 ON/OFF button
Press this button to switch the machine on. Press it
again to switch the machine off.
4 Programme selector dial
The selector is divided into 4 sections:
• Cotton, linen
• Synthetics
• Delicates, Wool , hand wash
• Special programmes A....D
• Reset programme O
The selector dial can be turned either clockwise or
anticlockwise.
Position Ecorresponds to the ENERGY SAVING
programmes and position to “cold wash”.
95°
60°
E
40°
E
40°
60°
40°
AA
30°
A
B
C
D
40°
60°
30°
30°
40°
40°
30°
30°
60°
At the end of the programme the selector dial
must be turned to position O.
Programme Option buttons
Depending on the programme, different functions
can be combined. These must be selected after
choosing the desired programme and before
depressing the START/PAUSE button.
When these buttons are pressed, the corresponding
pilot lights come on. When they are pressed again,
the pilot lights go out.
If an incorrect option is selected, the corresponding
pilot light flashes for about 2 seconds and message
Err is displayed.
5 Prewash button
Select this option if you wish your laundry to be
prewashed before the main wash (not available for
wool and handwash cycle).
The prewash cycle ends with a short spin at 650 r.p.m.
in programmes for cotton and synthetic fabrics,
whereas in the programme for delicate fabrics the
water is only drained.
6 Spin speed button
Press this button to reduce the maximum speed of the
final spin proposed by the machine for the selected
programme or to select position (no spin).
The light corresponding to the selected option
illuminates.
Maximum speeds are :
• Cotton, linen: 1000 r.p.m. for model EWS 1030
1200 r.p.m. for model EWS 1230
• Synthetic fabrics, wool, and hand wash: 900 r.p.m.
• For delicate fabrics: 700 r.p.m.
132990762 GB.qxd 14/12/2004 10.32 Pagina 8

ENGLISH
By selecting this option the spinning phases are
suppressed. To be selected for all the
programmes. If you select this option with
programmes for cotton and synthetics, the machine
will perform some extra rinses.
7 Rinse hold button
When you choose this option, the machine will not
drain the water of the last rinse, so as not to wrinkle
the laundry. At the end of the programme, the light of
the START/PAUSE button goes off, the pilot lights
and remain lit, the door is blocked to indicate
that the water must be drained. To empty out water
there are 2 possibilities:
• Select programme B (draining): The water is
emptied out without spinning.
• Select programme C (spin) or D (delicate spin).
Select the spin speed by means of the relevant
button and then depress the START/PAUSE button.
The water is emptied out and the laundry is spun at
the selected spin speed.
Attention!
Before choosing the programme B, Cor D
the selector dial has to be positioned on O
(cancelling).
8 Quick wash button
This option can be used for lightly soiled items (not for
wool, hand wash, E60°-E40°-AA40°-60° and 40° )
in order to obtain a good washing program in a short
time. The washing time will be reduced according to
the type of fabric and the selected temperature.
9 Super rinse button
This option can be selected with all programmes,
except the wool programme and handwash. The
machine will add 2 rinses to the selected program.
This option is recommended for people who are
allergic to detergents and in areas where the water is
very soft.
10 SENSITIVE button
Can be used with all cotton and synthetic
programmes. Adds one rinse to rinsing phase and
reduces or eliminates the intermediate spin phases.
11 DELAY START button
The wash programme can be delayed from 30 min –
60 min – 90 min, 2 hours and then by 1 hour up to a
maximum of 23 hours by means of this button.
Selecting the delayed start
• Select the programme and the required options.
• Select the delay start.
• Depress START/PAUSE button: the machine starts
its hourly countdown.
The programme will start after the selected delay
has expired.
Cancelling the delayed start
• Depress START/PAUSE button.
• Depress DELAY START button until the
symbol 0’ is displayed.
• Depress START/PAUSE button again.
Important!
The door will be locked throughout the delay time. If
you need to open the door, you must first set the
washing machine to Pause by pressing the
START/PAUSE button. After you have closed the
door, press the START/PAUSE button again.
12 Display
The display shows the following information:
Cancelling – Duration of the programme –
Delayed start – Incorrect option selection –
Alarm code – End of programme.
If a programme has been cancelled – programme
selector dial on position O– display and all the lights
are off.
After selecting a programme, the duration is
displayed in hours and minutes (for example 2.05).
2.05
Duration of the selected programme
Cancelling
9
No spin
132990762 GB.qxd 14/12/2004 10.32 Pagina 9

The duration is calculated automatically on the basis
of the maximum recommended load for each type of
fabric.
After the programme has started, the time remaining
is updated every minute.
The selected delay (23 hours max) set by means
of the relevant button appears on the display for
3 seconds, then the duration of the previously
selected programme is displayed.
The countdown is updated every hour.
If an option which is not compatible with the set
wash programme is selected, the message Err is
displayed for 2 seconds.
In the event of operating problems, some alarm
codes can be displayed, for example E20 (see
paragraph “Something not working”).
E20
Alarm codes
Incorrect option selection
Delayed start
When the programme has finished a flashing zero is
displayed.
13 START/PAUSE button
This button has two functions:
Start – Pause.
After having selected the required programme,
press this button to start the machine; the
corresponding pilot light stops flashing.
If you have selected the delayed start, the machine
begins its countdown. The duration of the
programme or the delay appears on the display.
To interrupt a programme which is running, depress
the START/PAUSE button: the corresponding pilot
light starts to flash.
To restart the programme from the point at which it
was interrupted, press the START/PAUSE button
again.
Pause
Start
End of programme
10
132990762 GB.qxd 14/12/2004 10.32 Pagina 10

ENGLISH
14 Programme progress display
By selecting the wash programme, the pilot lights
corresponding to the various phases making up the
programme come on.
After the machine has started, only the running
phase pilot light stays on. When the programme has
finished, the End pilot light comes on.
The END pilot light flashes in the event of
operating problems.
At the same time an alarm code appears on the
display.
E10 = the machine does not fill
E20 = the machine does not empty
E40 = the door has not been closed
To eliminate the problem, see paragraph “Something
not working”.
If at the end of the programme the pilot light
flashes this means that the drain filter must be
cleaned.
11
132990762 GB.qxd 14/12/2004 10.32 Pagina 11

Programme information
Washing programme for machine washable wool as
well as for hand washable woolens and delicate
fabrics with the “handwashing” care symbol.
These programmes have to be used for lightly or
normally soiled cotton and synthetic items. The
washing time will be reduced only by few minutes.
Cannot be used with the Quick wash button and
E 60°- E 40°- AA 40°- programmes.
With this programme it is possible to rinse and spin
the garments which have been washed by hand. The
machine performs 3 rinses, followed by a final spin at
the maximum speed.
The spin speed can be reduced by depressing
button .
The final spin is foreseen only for cotton items as in
the spin programme.
For emptying out the water of the last rinse in
programmes with the Rinse hold option.
Turn first the programme selector dial to O, then
select programme Band depress the
START/PAUSE button.
Separate spin at the maximum speed for hand-
washed garments. It has to be used for cotton items.
You can reduce the speed by means of button to
adapt it to the fabrics to be spun.
C = Spin
B = Drain
A = Rinses
60° and 40°
/ Wool/Handwash Separate short spin at the maximum speed 700 rpm
for hand washed garments. It has to be used for
synthetic, delicate, wool/handwashed, silk items. You
can reduce the speed by means of button
to adapt it to the fabrics to be spun.
To reset a programme turn the selector dial to O.
Now can a new programme be selected.
O = Cancelling
D = Delicate spin
12
132990762 GB.qxd 14/12/2004 10.32 Pagina 12

ENGLISH
13
Washing hints
Sorting the laundry
Follow the wash code symbols on each garment
label and the manufacturer’s washing instructions.
Sort the laundry as follows:
whites, coloureds, synthetics, delicates, woollens.
Temperatures
95° for normally soiled white cottons and linen
(e.g. tea cloths, towels, tablecloths,
sheets...)
60° for normally soiled, colour fast garments
(e.g. shirts, night dresses, pyjamas....) in
linen, cotton or synthetic fibres and for
lightly soiled white cotton (e.g. underwear).
(cold)for delicate items (e.g. net curtains), mixed
30°-40° laundry including synthetic fibres
and woollens.
Before loading the laundry
Never wash whites and coloureds together. Whites
may lose their “whiteness” in the wash.
New coloured items may run in the first wash; they
should therefore be washed separately the first time.
Make sure that no metal objects are left in the
laundry (e.g. hair clips, safety pins, pins).
Button up pillowcases, close zip fasteners, hooks
and poppers. Tie any belts or long tapes.
Remove persistent stains before washing. Rub
particularly soiled areas with a special detergent or
detergent paste.
Treat curtains with special care. Remove hooks or tie
them up in a bag or net.
Maximum loads
Recommended loads are indicated in the
programme charts.
General rules:
Cotton, linen: drum full but not too tightly packed;
Synthetics: drum no more than half full;
Delicate fabrics and woollens: drum no more than
one third full.
Washing a maximum load makes the most efficient
use of water and energy.
For heavily soiled laundry, reduce the load size.
Laundry weights
The following weights are indicative:
bathrobe 1200 g
napkin 100 g
quilt cover 700 g
sheet 500 g
pillow case 200 g
tablecloth 250 g
towelling towel 200 g
tea cloth 100 g
night dress 200 g
ladies’ briefs 100 g
man’s work shirt 600 g
man’s shirt 200 g
man’s pyjamas 500 g
blouse 100 g
men’s underpants 100 g
Removing stains
Stubborn stains may not be removed by just water
and detergent. It is therefore advisable to treat them
prior to washing.
Blood: treat fresh stains with cold water. For dried
stains, soak overnight in water with a special
detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab the
stain; treat several times.
Dried grease stains: moisten with turpentine, lay
the garment on a soft surface and dab the stain with
the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damaged and the
fabric tends to hole.
Mould stains: treat with bleach, rinse well (whites
and fast coloureds only).
Grass: soap lightly and treat with bleach (whites and
fast coloureds only).
Ball point pen and glue: moisten with acetone (*),
lay the garment on a soft cloth and dab the stain.
Lipstick: moisten with acetone as above, then treat
stains with methylated spirits. Remove any residual
marks from white fabrics with bleach.
Red wine: soak in water and detergent, rinse and
treat with acetic or citric acid, then rinse. Treat any
residual marks with bleach.
132990762 GB.qxd 14/12/2004 10.32 Pagina 13

Quantity of detergent to be used
The type and quantity of detergent will depend on
the type of fabric, load size, degree of soiling and
hardness of the water used.
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in
your area can be obtained from the relevant water
supply company, or from your local authority.
Follow the product manufacturers’ instructions on
quantities to use.
Use less detergent if:
– you are washing a small load,
– the laundry is lightly soiled,
– large amounts of foam form during washing.
Ink: depending on the type of ink, moisten the fabric
first with acetone (*), then with acetic acid; treat any
residual marks on white fabrics with bleach and then
rinse thoroughly.
Tar stains: first treat with stain remover, methylated
spirits or benzine, then rub with detergent paste.
(*) do not use acetone on artificial silk.
Detergents and additives
Good washing results also depend on the choice of
detergent and use of the correct quantities to avoid
waste and protect the environment. Although
biodegradable, detergents contain substances
which, in large quantities, can upset the delicate
balance of nature.
The choice of detergent will depend on the type of
fabric (delicates, woollens, cottons, etc.), the colour,
washing temperature and degree of soiling.
All commonly available washing machine detergents
may be used in this appliance:
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (60°C max)
and woollens,
– liquid detergents, preferably for low temperature
wash programmes (60°C max) for all types of
fabric, or special for woollens only.
The detergent and any additives must be placed in
the appropriate compartments of the dispenser
drawer before starting the wash programme.
If using concentrated powder or liquid detergents, a
programme without prewash must be selected.
The washing machine incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked just before starting the
programme.
Any fabric softener or starching additives must be
poured into the compartment marked before
starting the wash programme.
Follow the product manufacturer’s recommendations
on quantities to use and do not exceed the «MAX»
mark in the detergent dispenser drawer.
14
132990762 GB.qxd 14/12/2004 10.32 Pagina 14

ENGLISH
15
Operating sequence
Before the first wash we recommend that you pour 2
litres of water into the main wash compartment
of the detergent drawer in order to activate the
ECO valve. Then run a cotton cycle at 60°C, with the
machine empty, in order to remove any
manufacturing residue from the drum and tub.
Pour half a measure of detergent into the main wash
compartment and start up the machine.
1. Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
Close the door.
2. Measure out the detergent
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent recommended by the
manufacturer in a graduated cup and pour it into the
main wash compartment .
If you wish to carry out the prewash, pour detergent
into the appropriate compartment marked .
3. Measure out the additive
If required, pour fabric softener into the compartment
marked , without exceeding the «MAX» mark.
P1019
P1018
P0004
4. Switch the machine on
To switch the machine on, press the ON/OFF button:
the mains-on light comes on.
If the programme selector dial is on the RESET O
position, three flashing dashes will be displayed. If
the programme selector dial is positioned on a wash
programme, a flashing zero will be displayed.
5. Select the desired programme
Turn the programme selector dial to the desired
position: the lights corresponding to the different
phases making up the selected programme light on.
The duration of the programme appears on the
display.
6. Select the spin speed or option
Depress the spin speed button to choose the
required speed or option : the corresponding light
comes on.
EWS 1030 EWS 1230
900
700
500
1200
900
700
500
1000
95°
60°
E
40°
E
40°
60°
40°
AA
30°
A
B
C
D
40°
60°
30°
30°
40°
40°
30°
30°
60°
---
0
132990762 GB.qxd 14/12/2004 10.32 Pagina 15

10. Changing an option or a programme
during its cycle
It is possible to change any option before the
programme carries it out.
Before you make any change, you must pause the
washing machine by pressing the START/PAUSE
button.
Changing a running programme is possible only by
resetting it.
Turn the programme selector dial to O and then to
the new programme position. The washing water in
the tub will not emptied out. Start the new
programme by depressing the START/PAUSE
button.
11. Interrupting a programme
Depress the START/PAUSE button to interrupt a
programme which is running, the corresponding
light starts to flash. Depress the same button again
to restart the programme.
12. Opening the door after the
programme has started
First set the machine to PAUSE by pressing the
START/PAUSE button.
If the door does not open, this means that the machine
is already heating, that the water level is above the
bottom edge of the door or that the drum is turning.
If you cannot open the door but you need to open it
you have to switch the machine off by depressing the
ON/OFF button. After about 3 minutes the door can
be opened (pay attention to the water level and
temperature!). To restart the programme depress
ON/OFF button again after closing the door.
13. At the end of the programme
The machine stops automatically.
If the Rinse hold has been selected the porthole
remains blocked, the light of the START/PAUSE
button goes off, the pilot lights and remain lit,
to indicate that the water must be emptied out before
opening the door. The display shows a flashing zero.
Turn the programme selector dial to Reset O and
press ON/OFF button to switch the machine off .
Remove the laundry from the drum and carefully
check that the drum is empty so as to avoid any
forgotten items being damaged in a subsequent
wash (e.g. shrinking) or their colour running into a
load of whites.
If you do not intend to carry out another wash, close
the water tap.
Leave the door open to prevent the formation of
mildew and unpleasant smells.
16
7. Select the required options
The light corresponding to the depressed button
illuminates.
8. Select the DELAY START option
To delay starting of a programme, press the DELAY
START button. The figures corresponding to the
selected delay will be displayed for about 3 seconds,
after which the duration of the selected programme
will appear on the display.
During this period it is possible to load other laundry:
• depress START/PAUSE button;
• load the laundry;
• close the door and depress START/PAUSE button
again.
9. Start the programme
To start the selected programme, press the
START/PAUSE button; the corresponding light stops
flashing.
The pilot light corresponding to the wash phase
which is running is on.
The machine starts operating.
If you have selected the delayed start the machine
starts its countdown. The display shows the delay or
the duration of the programme.
+
132990762 GB.qxd 14/12/2004 10.32 Pagina 16

ENGLISH
17
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Energetic wash
Delicate wash
Max. wash
temperature
95°C
Max. wash
temperature
60°C
Max. wash
temperature
40°C
Max. wash
temperature
30°C
Hand wash Do not
wash
at all
Bleaching Bleach in cold water Do not bleach
Ironing Hot iron
max 200°C
Warm iron
max 150°C
Lukewarm iron
max 110°C
Do not iron
Dry cleaning Dry cleaning
in all solvents
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
pure alcohol
and R 113
Do not
dry clean
Drying Flat On the line On clothes
hanger
Tumble dry
high
temperature
low
temperature
Do not
tumble dry
95
60
60
40
40
40
30
30
132990762 GB.qxd 14/12/2004 10.32 Pagina 17

18
Programme chart
Washing programmes
* The consumption data shown on this chart is to be considered purely indicative, as it may vary depending
on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. It refers
to the highest temperature for each wash programme.
** In compliance with EC directive 92/75 the consumption figures indicated on the Energy label refer to this
programme at E60°C with a load of 4 kg of cotton items.
*** Fabrics washed with this programme have a washing efficiencyresult of AA.
60°- 95°
E60°**
30°- 60°
60° - 40°
E40°
40°AA***
-30°-60°
40°
30°-40°
-30°-40°
30°
Temp. Type of fabric Additional
functions
4 kg
4 kg
4 kg
4 kg
4 kg
4 kg
1.5 kg
1.5 kg
1.5 kg
1 kg
1 kg
Max.
load
1.8
0.76
1.0
1.0
0.76
0.76
0.7
0.4
0.5
0.35
0.25
47
44
44
44
44
44
42
42
50
48
48
145
130
110
100
150
150
89
93
60
55
51
Consumption*
Energy
kWh
Water
lt.
Time
min.
White
cotton
White cotton
economy
Coloureds
Whites and
Coloureds
Coloureds
economy
Cottons 40°AA
Synthetics
Synthetics
easy iron
Delicates
Wool
Handwash
Programme
description
Wash at 60°- 95°C
3 rinses
Normal spin
Wash at 60°C
3 rinses
Normal spin
Wash at 30°-60°C
3 rinses
Normal spin
Wash at 40°-60°C
3 rinses
Normal spin
Wash at 40°
3 rinses
Normal spin
Wash at 45°
3 rinses
Normal spin
Wash at 30°-60°C
or cold wash
3 rinses
Delicate spin
Wash at 40°C
4 rinses
Delicate spin
Wash at 30°-40°C
3 rinses
Delicate spin
Wash at 30°-40°C
or cold wash
3 rinses
Delicate spin
Wash at 30°C
3 rinses
Delicate spin
132990762 GB.qxd 14/12/2004 10.33 Pagina 18

ENGLISH
19
Programme chart
Special programmes
* The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on
the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.
A
B
C
D
O
Selector dial
position
Programme Additional
functions
4 kg
/
4 kg
1.5 kg
Max.
load
0.05
-
-
-
-
42
-
-
-
-
45
3
10
6
-
Consumption*
Energy
kWh
Water
lt.
Time
min.
Rinses
Drain
Spin
Delicate
spin
Cancelling
Programme
description
3 rinses with liquid
additives if required
Long spin
For emptying out
the last rinse of the
programmes with
option
Drain and long spin
Drain and delicate
spin
For cancelling the
wash programme
which is running
132990762 GB.qxd 14/12/2004 10.33 Pagina 19

20
Maintenance
Bodywork
Clean the outside of the machine with soap and
water only. Rinse with clean water and dry with a
soft cloth.
Important: do not use methylated spirits, solvents
or similar products to clean the bodywork.
Door seal
Check from time to time the door seal and eliminate
eventual possible objects that could be trapped in
the fold.
Detergent dispenser drawer
After a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it
under a running tap. To remove the drawer from the
machine, press the button in the rear left-hand
corner.
To facilitate cleaning, the top part of the additive
compartments can be removed.
P1021
P1020
P1050
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the
drawer after cleaning.
Drain pump
The pump should be inspected if
• the machine does not empty and/or spin
• the machine makes an unusual noise during
draining due to objects such as safety pins, coins
etc. blocking the pump.
Proceed as follows:
• Disconnect the appliance.
• If necessary wait until the water has cooled down.
• Open the pump door.
• Place a container close to the pump to collect any
spillage.
• Release the emergency emptying hose, place it in
the container and remove its cap.
• When no more water comes out, unscrew the
pump cover and remove the pump. Always keep a
rag nearby to dry up spillage of water when
removing the pump.
P1115
P1114
P0038
132990762 GB.qxd 14/12/2004 10.33 Pagina 20