Electrolux W465H User manual

2010.01.26
W475N/S, W485N/S, W4105N/S, W4130N/S 00521/402183-
W4180N/S 00650/107384-
W4250N/S 00725/105494-
W4330N/S 00795/102510-
Installation manual
Washer extractors
W465H, W475H/N/S, W485N/S, W4105H/N/S,
W4130H/N/S, W4180H/N/S, W4240H,
W4250N/S, W4300H, W4330N/S
Type W3...
Compass Control
From machine No.
438 9037-21/EN

3
Contents
Contents
Safety precautions .....................................................................................5
Technical data............................................................................................7
Installation, H-model................................................................................13
Transportation and unpacking, W465H, W475H, W4105H ................13
Transportation and unpacking, W4130H-W4300H .............................14
Siting and floor ....................................................................................15
Mechanical installation ........................................................................16
Installation, S- and N-model ....................................................................17
Siting ...................................................................................................17
Floor ....................................................................................................17
Casting a plinth ...................................................................................18
Installation on an excisting floor or foundation ...................................20
Installation on vinyl floor coverings .....................................................21
Installation, ships, oil-rigs, etc.............................................................22
Welding a foundation ..........................................................................23
Installing the machine .........................................................................24
Water connections ..............................................................................25
Drain connection .................................................................................27
Steam connection ...............................................................................28
Connection of external liquid supplies ................................................29
Functions for I/O-cards .......................................................................32
Machines with type 3 I/O ....................................................................39
Electrical installation............................................................................40
How to convert heating elements from 3AC to 1AC...........................48
Function checks.......................................................................................55
The manufacturer reserves the right to make changes to design and
component specifications.

5
Safety Precautions
All external equipment which is connected to the machine must be CE/EMC-approved
and connected using an approved shielded cable.
Safety Precautions
The machine is only intended for water-wash use.
Do not allow minors to use the machine.
Do not hose down the machine with water.
The machine's door lock must under no circumstances be bypassed.
If the machine develops a fault, this must be reported to the person in charge as soon
as possible. This is important both for your safety and that of others.
The machine is not intended to be used by people (including minors) with reduced
physical or mental capacity or lack of experience and knowledge. Such people must
be instructed in the use of the machine by a person who has responsibility for their
safety. Minors must be supervised to ensure that they do not play with the machine.
In order to prevent damage to the electronics (and other parts) that may occur as the
result of condensation, the machine should be placed in room temperature for 24 hours
before being used for the first time.

7
W465H W475H W4105H W4130H W4180H W4240H W4300H
65 75 105 130 180 240 300
520 520 595 650 725 795 795
49 49 49 49 44 42 42
1100 1100 1025 980 930 890 820
5.4/7.5 5.4/7.5 7.5/10 13 18 23 23
x x x x x x x
x x x x x x x
350 350 350 350 350 350 300
144 159 201 267 350 400 509
64 65 69 70 75 78 76
W465H W475H W4105H W4130H W4180H W4240H W4300H
DN20 DN20 DN20 DN20 DN20 DN20 DN20
3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4"
200-600 200-600 200-600 200-600 200-600 200-600 200-600
50-1000 50-1000 50-1000 50-1000 50-1000 50-1000 50-1000
20 20 20 20 30 60 60
50/75 50/75 50/75 75 75 75 75
170 170 170 170 170 170 170
DN15 DN15 DN15 DN15 DN15 DN15 DN15
1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2"
300-600 300-600 300-600 300-600 300-600 300-600 300-600
50-800 50-800 50-800 50-800 50-800 50-800 50-800
Innerdrum
volume litres
diameter mm
Drum speed
wash
extraction
rpm
Heating
electricity kW
steam
hot water
G-factor
Weight, net kg
Sound pressure level
dB (A)
Connections
Water valves
connection
BSP
Rec. water pressure
kPa
Functioning limits
for water valve
kPa
Capacity
at 300 kPa
l/min
Drain valve
outer Ø mm
Draining capacity
l/min
Steam valve
connection
BSP
Rec. steam pressure
kPa
Functioning limits for
steam valve
kPa
Technical data
Technical data

8Technical data
W475N/S W485N/S W4105N/S W4130N/S W4180N/S W4250N/S W4330N/S
75 85 105 130 180 250 330
520 520 595 595 650 725 795
49 49 49 49 44 44 42
587/830 587/830 548/776 548/776 525/742 497/702 474/671
2.0/3.0/ 2.0/3.0/5.6 3.0/6.5/ 3.0/ 4.8/9.3
5.4/5.6/7.5 5.4/7.5 7.5/10 7.5/10 13 18 23
x x x x x x x
x x x x x x x
100/200 100/200 100/200 100/200 100/200 100/200 100/200
129 135 145 175 228 287 330
63/59 63/59 63/64 70/64 64/70 68/73 70
W475N/S W485N/S W4105N/S W4130N/S W4180N/S W4250N/S W4330N/S
DN20 DN20 DN20 DN20 DN20 DN20 DN20
3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4"
200-600 200-600 200-600 200-600 200-600 200-600 200-600
50-1000 50-1000 50-1000 50-1000 50-1000 50-1000 50-1000
20 20 20 20 30 60 60
75 75 75 75 75 75 75
170 170 170 170 170 170 170
DN15 DN15 DN15 DN15 DN15 DN15 DN15
1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2"
300-600 300-600 300-600 300-600 300-600 300-600 300-600
50-800 50-800 50-800 50-800 50-800 50-800 50-800
Innerdrum
volume litres
diameter mm
Drum speed
wash
extraction
rpm
Heating
electricity kW
steam
hot water
G-factor
Weight, net kg
Sound pressure level
dB (A)
Connections
Technical data
Water valves
connection
BSP
Rec. water pressure
kPa
Functioning limits
for water valve
kPa
Capacity
at 300 kPa
l/min
Drain valve
outer Ø mm
Draining capacity
l/min
Steam valve
connection
BSP
Rec. steam pressure
kPa
Functioning limits for
steam valve
kPa

9
K
N
M
R
P
6
F
5
1
O
G
I
L
3
2
7
4
5283 B
Technical data
A B C D E F G H I K L M N O P R S
W465H 720 690 1115 355 720 825 45 1030 220 1010 135 910 830 360 100 240 –
W475H 720 690 1115 355 720 825 45 1030 220 1010 135 910 830 360 100 240 –
W4105H 830 705 1200 365 740 945 45 1115 220 1095 135 995 910 415 100 295 –
W4130H 910 785 1325 435 825 1035 125 1245 215 1225 300 1125 – – 100 305 455
W4180H 970 870 1410 470 910 1120 115 1330 230 1290 315 1205 370 410 100 335 485
W4240H 1020 915 1445 500 955 1155 100 1360 215 1320 300 1240 350 360 100 360 510
W4300H 1020 1060 1445 500 1135 1155 100 1360 215 1320 300 380 – – 100 360 330
A
8
9
10
C
D
5281 B
B
E
6
5282 B
W465H, W475H, W4105H, W4130H
A
9
10
8
D
C
5377 A
5379 A
B
E
6
G
SL
M
I
5
1
F
6
P
R
KH
5378 A
7
3
2
2
W4180H, W4240H, W4300H
Rear side
1 Electrical connection
2 Cold water
3 Hot water
4 Hard water
5 Steam connection
6 Drain
7 Liquid detergent supply
8 Control panel
9 Soap box
10 Door opening, W465H, W475H: ø 310, W4105H: ø 365, W4130H: ø 395, W4180H, W4240H, W4300H: ø 435
Front Right side
Rear side
Front Right side

10 Technical data
A B C D E F G H I K L M N O P R
W475N/S 660 690 1115 355 725 825 45 1030 215 1010 130 830 385 - 100 225
W485N/S 660 730 1115 355 765 825 45 1030 215 1010 130 830 385 - 100 225
W4105N/S 720 705 1200 365 740 910 45 1115 215 1095 130 910 420 - 100 235
W4130N/S 720 790 1200 365 825 910 45 1115 215 1095 130 910 420 - 100 235
W4180N/S 750 880 1333 435 915 1035 45 1245 130 1225 210 1040 325 295 100 225
W4250N/S 830 955 1410 470 990 1120 45 1330 160 1290 245 1125 325 325 100 265
W4330N/S 910 1040 1445 500 1075 1155 45 1365 160 1325 245 1155 280 325 100 210
87
C
D
A
10
5281
B
E
5
5282
N
G
I
F
L
R
P
H
M
K
5
4
1
3
2
6
5283
9
W475N/S-W4130N/S
M
P
F
K
I
L
G
R
H
O
N
4
1
5
3
29
6
5459
W4180N/S-W4330N/S
Rear side
1 Electrical connection
2 Cold water
3 Hot water
4 Steam connection
5 Drain
6 Liquid detergent supply
7 Control panel
8 Soap box
9Water reuse
10 Door opening, W475N/S, W485N/S: ø310, W4105N/S, W4130N/S: ø365, W4180N/S: ø395,
W4250N/S, W4330N/S: ø435
Front Right side
Rear side

11
W465H W475H W4105H W4130H W4180H W4240H W4300H
18.3 18.3 17.1 16.3 15.5 14.8 13.7
1.8 ± 0.5 1.9 ± 0.5 2.5 ± 0.5 3.1 ± 0.5 4.2 ± 1.0 5.2 ± 1.0 6.2 ± 1.2
Frequency of the
dynamic force
Hz
Max floor load
at extraction
kN
Technical data
W475N/S W485N/S W4105N/S W4130N/S W4180N/S W4250N/S W4330N/S
Frequency of the
dynamic force
Hz 9.3 9.3/13.8 8.7/12.9 8.7/12.9 8.3/12.3 7.9/11.7 7.5/11.2
Max floor load
at extraction 1.6 ± 2.8/ 1.7 ± 3.1/ 2.1 ± 3.6/ 2.3 ± 4.1/ 2.9 ± 4.7/ 3.7 ± 5.3/ 4.5 ± 5.8/
kN 1.6 ± 2.3 1.7 ± 2.6 2.1 ± 3.0 2.3 ± 3.7 2.9 ± 4.6 3.7 ± 5.8 4.5 ± 6.8

13
Installation
5325
2
5326
3
5327A
1
1
2
3
Installation H-model
Transportation and unpacking,
W465H, W475H, W4105H
The machine is delivered complete with expan-
sion bolts etc. packed inside the machine in the
drum.
The machine is delivered bolted onto the trans-
port pallet and packed in a crate or box.
• Removepackingfromthemachine.
• Removefrontpanel.Removethebolts
between the machine and pallet.
• Mountfrontpanel.
When the machine is lifted off the pallet: Make
sure that the machine does not come down on
the floor with either of the rear corners first. The
side panel of the machine can be damaged.
• Mountthefeet.
• Placethemachineonitsnalposition.
• Levelthemachinewiththefeetofthe
machine.
The machine also comes with transport safety
devices (four plate angles between the support
and the drum).
In order to remove the safety devices:
• Removefrontandrearpanel.
• Removebothfrontmetalangels.
• Removebothrearmetalangels.
• Themachinemaynotbemovedwiththe
transport securities removed. Save the trans-
port securities for future use.

14 Installation
5340
4
6445
5
5341
6
5
1
4
6
Transportation and unpacking,
W4130H, W4180H, W4240H, W4300H
The machine is delivered complete with expan-
sion bolts etc. packed inside the machine in the
drum.
The machine is delivered bolted onto the
transport pallet and packed in a crate or box.
• Removepackingfromthemachine.
• Removefrontandrearpanel.Removethe
bolts between the machine and pallet.
• Mountfrontandrearpanel.
• Mountthefeet.
NOTE!
Regarding W4300H note the positioning of
the two front feet.
• Placethemachineonitsnalposition.
• Levelthemachinewiththefeetofthe
machine.
The machine also comes with transport safety
devices (two plate angles between the support
and the drum).
In order to remove the safety devices:
• Removethetwosidepanels.
• Removethetwotransportsecurities.
• Themachinemaynotbemovedwiththe
transport securities removed. Save the trans-
port securities for future use.

15
Installation
5327
7
7
Siting and floor
Install the machine close to a floor drain or open
drain.
In order to make installation and servicing the
machine easier the following clearances are
recommended:
• Atleast500mmbetweenthemachineand
the wall behind
• andmin.50mmonbothsidesofthemachine
whether installed next to the wall or other
machines.

16 Installation
5358
8
A
C
E
B
D
G
F
H
Front
A B C D E F G H
W465H 495 460 110 130 375 170 40 100
W475H 495 460 110 130 375 170 40 100
W4105H 575 465 130 140 455 185 35 95
W4130H 635 490 135 175 515 195 60 110
W4180H 715 545 125 205 595 185 60 115
W4240H 790 615 115 180 670 175 60 115
W4300H 790 755 60 180 670 175 60 75
8
= position of feet
= drilling points for expander bolts
• Themachineshallbeliftedinthebottom
frame.
• Placethemachineoverthetwodrilledholes.
• Checkthatthemachineisplacedinlevel.
Adjust with the feet.
It is of utmost importance that the machine
is placed in level, from side to side as well
as front to rear. If the machine is not pro-
perly leveled, it may result in out-of-balance
without a real out of balance in the drum.
• Inserttheexpansionboltssuppliedinthe
holes drilled in the floor. Fit the washers and
nuts, and tighten well.
Mechanical installation
• Markanddrill2holes(ø8mm)about40mm
deep (W465-W4105) and ø 10 mm and 50 mm
deep (W4130-W4240) in the positions shown.

17
Installation
9
5327
9
Installation S- and N-model
Leave the machine on the transport pallet until it
can be placed in the final, prepared position.
Siting
Install the machine close to a floor drain or open
drain. In order to make installation and servicing
the machine easier the following clearances are
recommended:
 • Atleast500mmbetweenthemachineand
the wall behind.
 • Minimum25mmtonextmachineifmorethan
one machine are installed on a foundation.
Floor
In this type of machine, the drum is attached di-
rectly to the frame. As a result the floor under the
machine must be stable enough to absorb the
dynamic forces generated during spin cycles.
For that reason, the mounting bolts must be cast
into the floor material itself.
When fixing the machine to an existing cement
floor, it must be and at least 100 mm thick.
The floor must be able to withstand the loads in-
dicated in the table.
If it isn’t possible to cast the bolts into the floor,
an alternative might be to use so-called chemical
anchors. Your local dealer can provide the infor-
mation you need.

18 Installation
5462
0899
11
10



150-200 mm
40 mm
10
11
12
Casting a plinth
A plinth should be used where the existing floor
is less than 100 mm thick or in order to ensure
that the machine is above the level of any water
leakages.
The plinth should be approximately 150 - 200
mm in height.
Proceed as follows:
 • Breakuptheexistingoortoadepthofap
prox. 75 mm and check that the sides of the
hole are tapered outward so that the longest
side at the bottom measures 120 mm more
than at the top.
 • Makethemouldfortheplinth.
 • Moistentheholewellandapplycementtothe
sides and bottom.
 • 4boltsmustbesetintotheconcreteofthe
machine base. The bolts need to project 40
mm out of the base. Pour the concrete into
the prepared base mould and make sure that
the surface is level.
 • Theconcreteshouldbelefttosetforatleast
two days before mounting the machine on the
plinth.

19
Installation
A B C D E F G H I
W475N 685 660 495 395 115 635 - - -
W485N 725 660 495 445 115 665 - - -
W4105N 700 720 575 385 120 695 - - -
W4130N 785 720 575 495 120 760 - - -
W4180N 875 750 635 570 120 855 - - -
W4250N 950 830 715 635 125 955 - - -
W4330N 1035 910 790 695 135 1050 810 10 95
W475S 685 660 495 395 115 635 495 0 75
W485S 725 660 495 445 115 665 495 0 75
W4105S 700 720 575 385 120 695 595 10 80
W4130S 785 720 575 495 120 760 595 10 80
W4180S 875 750 635 570 120 855 655 10 85
W4250S 950 830 715 635 125 955 735 10 85
W4330S 1035 910 790 695 135 1050 810 10 95
0948 A
12
 









Models S and W4330N
In these models, two expander bolts must also be fitted to the front sec-
tion of the machine.
• Drilltwoholes(1)ø10mmand40mmdeep.
• Afterthemachinehasbeenplacedovertheotherfourbolts,placethe 
two spacer washers over the two holes. They shall be placed between
the machine and foundation.
• Mounttheexpenderboltsinthedrilledholesandfastenthemachine. 
Don´t forget the washers.

20 Installation
5917
13
5918
14
5919
15
5920
16
5921
17
5922
18
13
14
15
16
17
18
Installation on an excisting floor or foundation
Instead of braking up the excisting floor or foun-
dation, chemical bolts M16 can be used.
Mounting instruction
• Drillø18mm(11/16")toadepthof125mm
(5"). Do not make the hole too deep.
• Cleanthedrilledholes.
• Putdownthechemicalampuleinthehole.
• Rotatetheboltintothehole,sothattheglass
ampule is broken and its contents mixed.
• Rotatethebolttocorrectdepth.
NOTE! Do not rotate the bolt against the con-
crete bottom. Check that the chemicals have
filled the hole completely.
• Removethedrillingmachinewiththemoun-
ting tool. Hold the bolt with one hand. Let the
bolt harden before the machine is mounted.
Time for hardening, due to different concrete
temperatures.
– 10°C 6 hours
– 5°C 2.5 hours
± 0°C 1 hour
5°C 30 minutes
10°C 20 minutes
15°C 15 minutes
20°C 10 minutes