Electrolux washing machine User manual

SSD-P APdV, EB, HD 01/05 I599 34 71-47
SERVICE MANUAL
WASHING
Publication no.
599 34 71-47
ELECTROLUX-ZANUSSI S.p.A.
SPARE & SERVICE DOCUMENTATION
Corso Lino Zanussi,30
I - 33080 PORCIA /PN
ITALY
Fax [phone]
Edition: 2001.05.31
EN/eb
Diagnostics Guide to
EWM2000 Electronic
Control
WASHING MACHINES
&
WASHER DRYERS
Production: ZP Porcia (Italy)

SSD-P APdV, EB, HD 01/05 II 599 34 71-47

SSD-P APdV, EB, HD 01/05 III 599 34 71-47
CONTENTS
Aim of this manual .............................................................................................................. page IV
OPERATING PROCEDURE .............................................................................................. page IV
SUMMARY OF EWM2000 ELECTRONIC CONTROLS .................................................... page V
Table 1: FULL SMD VERSION with on/off button .............................................................. pages 1.1-1.2
Table 2: FULL SMD VERSION with on/off switch on the programme selector.................. pages 2.1-2.2
Table 3: DELTA3 & NEAT VERSION................................................................................. pages 3.1-3.2
Table 4: INPUT VERSION.................................................................................................. pages 4.1-4.2
Table 5: AEG VERSION (with on/off switch on the programme selector).......................... pages 5.1-5.2
DIAGNOSTIC CYCLES Phases......................................................................................... page 6.1
NO ACCESS TO DIAGNOSTICS PROGRAMME ............................................................. page 7.1
ALARM CODES.................................................................................................................. pages 8.1-8.35
HOW TO CHECK COMMUTATOR MOTORS ................................................................... page 9.1
CONFIGURATION CODE .................................................................................................. page 10.1
BASIC CIRCUIT DIAGRAM ............................................................................................... pages 11.1-11.3
MAIN ELECTRONIC BOARD CONNECTORS.................................................................. pages 12.1-12.3
BURNING MARKS ONMAIN ELECTRONIC BOARDS.................................................... pages 13.1-13.2
PICTURES LINKED TO FAULT FINDING ......................................................................... pages 14.1-14.10

SSD-P APdV, EB, HD 01/05 IV 599 34 71-47
INTRODUCTION
Aim of this manual
This manual aims to explain in a clear and simple way the phases a Service Engineer
should follow to solve problems highlighted by the different alarm codes in EWM2000
electronic appliances with electronic control.
Operating procedure
1. Find the type of control involved by checking the summaryat pageV.
2. Every user interface is connected with a summary table of the operations necessary to
read the possible alarms, to access the diagnostic cycle and to configurate the main
electronic board (see column “Diagnostic Table”).
3. Read the memorized alarm and consult the relative information (see “alarm codes”,
from page 8.1).
4. Delete memorized alarm.
5. If you cannot access the diagnostic cycle, consult chapter “No access to diagnostic
cycle” (page 7.1).
6. In case of replacement of main PCB check if there are burn marks (see page 13.1-
13.2)
7. After every replacing of the main electronic board, you need to configurate the module.
You can find further information about the configuration code at page10.1
(”configuration code”).
8. After every operation, check the functioning of the appliance through the diagnostic
cycle. For further information see page 6.1 (diagnostic cycle phases)
9. (Delete memorized alarm).

SUMMARY OF EWM2000 ELECTRONIC CONTROLS (ZP)
SSD-P APdV, EB, HD 01/05 V599 34 71-47
Type Styling Marks User interface Manuals (actual) Note Diagnostics table Examples of control panels
599 34 00-75; 599 33 70-05
599 34 05-08 Alarm Led 1
Alpha 2 Electrolux
A.Martin- Electrolux 599 34 20-83 Obstructed
filter Led 1
599 34 00-75; 599 33 70-05
599 34 05-08 Alarm Led 1
Ellipse
Privileg, Zoppas
Husqvarna,
Rosenlew, AEG,
Marynen, Hansa 599 34 20-83 Obstructed
filter Led 1
Multipanel
(Built-in)
Electrolux
Zanussi, AEG
Privileg
599 34 55-61
With
ON/OFF
button
1
FULL SMD
Sigma Zanker 599 34 37-91
Selector
with
ON/OFF 2
Delta 3 Zanussi, Rex 599 34 27-56 3
DELTA 3
Neat
(Jetsy-
IZ)
Zanussi, Rex, Aeg
Privileg, Electrolux,
Elektro-Helios
599 34 22-16 3
INPUT
Input
Rex
Zanussi
Privileg
599 34 22-87 4
599 34 15-14 Standard 5
AEG
Aeg Aeg
Privileg 599 34 39-45 Far East 5
BIG
SIZE
Multipanel
(first
version)
Zanker
Elektro-Helios 599 33 52-03 1

SSD-P APdV, EB, HD 01/05 VI 599 34 71-47

Table 1:FULL SMD with on/off button version
(the programme selector can be on the right or on the left of the module)
SSD-P APdV, EB, HD 01/05 1.1 599 34 71-47
ACCESS TO THE
DIAGNOSTICS
To access the diagnostics system:
→switch off the appliance and turn the programme selector knob
to RESET
→press the START/PAUSE button together with one of the other
buttons and then, holding down both buttons, press the
ON/OFF button to switch on the appliance.
→hold both buttons down until the buzzer (if featured) sounds and
the LEDs begin to flash (about 4 seconds)
DIAGNOSTIC CYCLE
→Correct operation of all the components in the appliance can be
checked by turning the programme selector knob clockwise.
1. Operation of the user interface (step 0, page 6.1)
2. Water fill to wash compartment (step 1, page 6.1)
3. Water fill to pre-wash compartment (step 2, page 6.1)
4. Water fill to conditioner compartment (step 3, page 6.1)
5. Hot water fill or fill to bleach compartment (certain models only)
(step 4, page 6.1)
6. Heating and, in Jetsystem models, recirculation (step 5, page
6.1)
7. Check for leaks from tub (step 6, page 6.1)
8. Drain and spin, check for pressure switch congruency (step 7,
page 6.1)
9. Drying (washer/dryers only) (step 8, page 6.1)
ALARMS
To read the last alarm condition, after accessing the diagnostics
system:
→turn the programme selector knob two positions counter-
clockwise from the RESET position (23 o 11).
Cancelling the last alarm condition
→press START/PAUSE button and no. 6button at the same time
during the course of the diagnostic cycle (2÷9).
→The alarm is cancelled also when a new configuration is given to
the main PCB.
CONFIGURATION OF THE MAIN PCB
To access the machine configuration procedure, first enter the
diagnostics system, and then:
→turn the programme selector one position counter-clockwise; the
display window shows the code relative to the position of the
programme selector and, after two seconds, the code relative to
the first of the 16 digits of the configuration code (position 0).
→when one of the option buttons is pressed (with the exception of
the START/PAUSE button), all the digits which make up the
configuration code are displayed in sequence.
→press the START/PAUSE button to modify the configuration
code (digit by digit).
→when all 16 digits have been entered, check that the code is
correct, then memorize the code by pressing the
START/PAUSE button and one of the option buttons at the
same time; these buttons should be held down until the buzzer
(if featured) sounds.
EXITING THE DIAGNOSTIC
→To exit the diagnostic cycle, switch the appliance off, on, and
then off again.

Table 1:FULL SMD with on/off button version
(the programme selector can be on the right or on the left of the module)
SSD-P APdV, EB, HD 01/05 1.2 599 34 71-47
Closure of selector contacts
(C6 = common)
PROGRAMME SELECTOR 24-position
selector knob
12-position
selector knob
(C1 not present) C1 C2 C3 C4 C5
Display
code
1 - Reset 1 - Reset ●●●● 1 E
22 ●●
0 6
3- ●● 1 4
43 ●● 0 C
5- ●●● 1 C
64 ●● 0 A
7-
●0 1
8-
●●
0 3
9-
●●
0 9
10 5 ●●●
0 E
11 - ●●
1 2
12 - ●●●
0 b
13 - ●● 1 1
14 - ●● 1 8
15 6 ●●●
1 3
16 - ●●● 1 A
17 7 ●●● 1 9
18 8 ● ●●● 1 b
19 - ●● 0 5
20 9 ●● ● 1 6
21 - ●0 2
22 10 ●0 4
23 11 ●0 8
24 12 ●1 0
● closed contact
Table of button codes
BUTTONNo. 012345678
L5 ❍❍❍❍❍❍❍❍●
L6 ❍❍❍❍●●●●❍
L7 ❍❍● ●❍❍●●❍
LED
L8 ❍●❍●❍●❍●❍
❍LED off
●LED lit
BINARY CODES
The table below can be used to convert the binary code shown by the LEDs into the corresponding letter or
decimal number
0123456789101112131415
value AbCdEF
8
❍❍❍❍❍❍❍❍●●●●●●●●
4
❍❍❍❍●●●●❍❍❍❍●●●●
2
❍❍●●❍❍●●❍❍●●❍❍●●
1
❍●❍●❍●❍●❍●❍●❍●❍●
❍LED off
●LED lit

Table 2:FULL SMD version with on/off switch on the programme selector
(the programme selector can be on the right or on the left of the module)
SSD-P APdV, EB, HD 01/05 2.1 599 34 71-47
ACCESS TO THE
DIAGNOSTICS
To access the diagnostics system:
→switch off the appliance
→press the START/PAUSE button (8) together with one of the
other buttons and then, holding down both buttons, switch on
the appliance by turning the programme selector one position
clockwise.
→hold both buttons down until the buzzer (if featured) sounds and
the LEDs begin to flash (about 4 seconds).
DIAGNOSTIC CYCLE
→Correct operation of all the components in the appliance can be
checked by turning the programme selector knob clockwise.
2. Operation of the user interface (step 0, page 6.1)
3. Water fill to wash compartment (step 1, page 6.1)
4. Water fill to pre-wash compartment (step 2, page 6.1)
5. Water fill to conditioner compartment (step 3, page 6.1)
6. Hot water fill or fill to bleach compartment (certain models only)
(step 4, page 6.1)
7. Heating and, in Jetsystem models, recirculation (step 5, page
6.1)
8. Check for leaks from tub (step 6, page 6.1)
9. Drain and spin, check for pressure switch congruency (step 7,
page 6.1)
10. Drying (washer/dryers only) (step 8, page 6.1)
ALARMS
To read the last alarm condition, after accessing the diagnostics
system:
→turn the programme selector knob to the last position but one
(23 or 11).
To cancel the last memorised alarm condition:
→press START/PAUSE button (8) and no. 4 button at the same
time during one of the 8 phases of the diagnostic cycle and not
in the alarm or configuration reading positions.
→The alarm is cancelled also when a new configuration is given to
the main PCB.
CONFIGURATION OF THE MAIN PCB
To access the machine configuration procedure, first enter the
diagnostics system, and then:
→turn the programme selector clockwise to the last position (24
or 12); the code relative to the programme selector is displayed
and after 2 seconds the code relative to the first of the 16 digits
of the configuration code (position 0) is displayed
→when one of the option buttons is pressed (with the exception of
the START/PAUSE button), all the digits, which make up the
configuration code, are displayed in sequence.
→press the START/PAUSE button (8) to modify the configuration
code (digit by digit).
→when all 16 digits have been entered, check that the code is
correct, then memorize the code by pressing the
START/PAUSE button and one of the option buttons at the
same time; these buttons should be held down for at least 4
seconds (i.e. the buzzer sounds).
EXITING
→To exit the diagnostic cycle, switch the appliance off, on, and
then off again.

Table 2:FULL SMD version with on/off button on the programme selector
(the programme selector can be on the right or on the left of the module)
SSD-P APdV, EB, HD 01/05 2.2 599 34 71-47
Closure of selector contacts
(C6 = common)
PROGRAMME SELECTOR 24-position
selector knob
12-position
selector knob
(C1 not present) C1 C2 C3 C4 C5
Display
code
1 - Reset 1 - Reset ●●●● 1 E
22 ●●
0 6
3- ●● 1 4
43 ●● 0 C
5- ●●● 1 C
64 ●● 0 A
7-
●0 1
8-
●●
0 3
9-
●●
0 9
10 5 ●●●
0 E
11 - ●●
1 2
12 - ●●●
0 b
13 - ●● 1 1
14 - ●● 1 8
15 6 ●●●
1 3
16 - ●●● 1 A
17 7 ●●● 1 9
18 8 ● ●●● 1 b
19 - ●● 0 5
20 9 ●● ● 1 6
21 - ●0 2
22 10 ●0 4
23 11 ●0 8
24 12 ●1 0
● closed contact
Table of button codes
BUTTONNo. 012345678
L20 ❍❍❍❍❍❍❍❍●
L21 ❍❍❍❍●●●●❍
L22 ❍❍●●❍❍● ●❍
LED
L23 ❍●❍●❍●❍●❍
❍LED off
●LED lit
BINARY CODES
The table below can be used to convert the binary code shown by the LEDs into the corresponding letter or
decimal number
0123456789101112131415
Value
AbCdEF
8
❍❍❍❍❍❍❍❍●●●●●●●●
4
❍❍❍❍●●●●❍❍❍❍●●●●
2
❍❍●●❍❍●●❍❍●●❍❍●●
1
❍●❍●❍●❍●❍●❍●❍●❍●
❍LED off
●LED lit