Electrolux WB6-90 User manual

Installation manual
Washer-extractors
WB6 70- WB6 90 – WB6 110
original instructions 01201217/EN

Contents
Contents
1 Safety precautions...............................................................................................................................5
1.1 Symbols.................................................................................................................................. 11
1.2 Personal protection equipment..................................................................................................12
1.3 Preliminary instructions ............................................................................................................12
1.4 Data plate explanation..............................................................................................................14
1.5 Warranty terms and exclusions .................................................................................................17
2 Environmental information .................................................................................................................18
3 Locking and tagging procedure...........................................................................................................18
4 Handling...........................................................................................................................................20
4.1 Lifting with a fork-lift truck .........................................................................................................20
4.2 Lifting with handlings straps......................................................................................................20
5 Packing-Weight.................................................................................................................................21
5.1 Packing...................................................................................................................................21
5.2 Weight ....................................................................................................................................22
6 Technical characteristics ....................................................................................................................22
6.1 Explanation of following installation drawings ............................................................................22
6.2 Washer extractor type WB6 70..................................................................................................23
6.3 Connections WB6 70 :..............................................................................................................26
6.4 Washer extractor type WB6 90..................................................................................................29
6.5 Connections WB6 90 :..............................................................................................................32
6.6 Washer extractor type WB6 110 ................................................................................................35
6.7 Connections WB6 110 : ............................................................................................................38
7 Sound levels .....................................................................................................................................40
8 Working place lighting........................................................................................................................40
9 Supplies ...........................................................................................................................................41
10 Barrier partition .................................................................................................................................42
11 Mechanical installation.......................................................................................................................44
11.1 Unpacking...............................................................................................................................44
11.2 Installation...............................................................................................................................44
11.3 Installing the shock absorber runners ........................................................................................44
11.4 Instructions for securing the machine on the ground ...................................................................45
11.5 Setting the bolsters ..................................................................................................................47
12 Remove of the transport locks fitted ....................................................................................................47
13 Drain connection ...............................................................................................................................48
14 Waters connections ...........................................................................................................................49
15 Liquid detergents connection..............................................................................................................51
15.1 Connection scheme of liquid detergents ....................................................................................53
15.2 Electrical liquid detergents' connection ......................................................................................54
16 Steam connection .............................................................................................................................56
17 Air vent connection............................................................................................................................57
18 Note about the A.C. power .................................................................................................................59
19 Feeder cable sections........................................................................................................................59
20 Electricity power supply .....................................................................................................................61
21 Compressed air connection................................................................................................................63
22 Function checks ................................................................................................................................64
23 Explanation of washing symbols.........................................................................................................67
23.1 Washing..................................................................................................................................67
23.2 Bleaching................................................................................................................................67
23.3 Drying.....................................................................................................................................68
23.4 Ironing ....................................................................................................................................68
23.5 Dry or water cleaning ...............................................................................................................68
24 Conversion of measurement units.......................................................................................................70
The manufacturer reserves the right to make changes to design and component specifications.

Installation manual 5
1 Safety precautions
CAUTION
READ THIS ENTIRE MANUAL BEFORE USAGE
This machine should be installed in conformance to the health and safety regulations, and only used in a sufficiently aerated area.
Check the instructions before installing or using the machine.

6Installation manual
CAUTION
Before any use, to retire all the parts needed to install the machine put in the drum ,
please follow these actions
1. connect compressed air.
2. Remove the side housing cabinet.
3. Push on the orange button of the D9/D10 distribution unit in the electric cabinet.
(see drawing below)
4. Open the loading door.
5. Open the drum doors , with precautions, maintain the 2 doors.
6. Get the package and instructions.

Installation manual 7
CAUTION
Users must have learnt how the machine operates.
This device must not be installed in places accessible to the public.
The machine is only intended for water-wash use.
Do not allow minors to use the machine.
Do not hose down the machine with water.
Only use detergent intended for water-wash of textiles Never use dry cleaning agents.
It is forbidden to wash textiles soaked with solvents.
The machine's door lock must under no circumstances be bypassed.
If the machine develops a fault, this must be reported to the person in charge as soon
as possible. This is important both for your safety and that of others.
DO NOT MODIFY OR TAMPER WITH THIS APPLIANCE.
Servicing shall be carried out only by authorised personnel by ELECTROLUX
PROFESSIONAL.
Only original spare parts shall be used.
When performing service or replacing parts, the power must be disconnected.
When the power is disconnected, the operator must see that the machine is discon-
nected (that the plug is removed and remains removed) from any point to which he has
access. If this is not possible, due to the construction or installation of the machine, a
disconnection with a locking system in the isolated position shall be provided.
In accordance with the wiring rules : mount a multi-pole switch prior to the machine to
facilitate installation and service operations.
In order to prevent damage to the electronics (and other parts) that may occur as the
result of condensation, the machine should be placed in room temperature for 24 hours
before being used for the first time.
In case of a gas heated machine, do not assemble the machine on premises contain-
ing a dry cleaning machines or other similar machines.
Please wash only items offering appropriate distribution inside the drum.
Do not wash items such as mattresses or shoes.
Call our technical departments before washing nonstandard items. Noncompliance
with these instructions may void the manufacturer's guarantee in case of abuse of the
washer-extractor.
CAUTION
For the following countries : AT, BE, BG, HR, CY, CZ, DK, EE, FI, FR, DE, GR, HU, IS,
IE, IT, LV, LT, LU, MT, NL, NO, PL, PO, PT, RO, SK, SI, ES, SE, CH, TR, UK : This ap-
pliance shall not be installed where the public has access.
For other countries : This appliance is not intended for use by persons (including chil-
dren) with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety and understand the hazards in-
volved. Children should be supervised to ensure that they do not play with the
appliance.

8Installation manual
IMPORTANT
The identification plate is located on the right side near the main switch.
Never use the main switch as an emergency stop. Use it only when the machine does
not work in progress. Instead of that, use the emergency stop buttons in both sides of
the machine.
IMPORTANT
Sound pressure level is found in Technical data.
CAUTION
Your machine is equipped with an automatic weighing system which weighs the laun-
dry during the loading and unloading cycle. For proper operation of this system, you
should not open the tank doors for the all duration of the wash program initiated
even if errors occurs.
IMPORTANT
Never try to open the outer drum door before the complete stop of the cage.
CAUTION
Disconnect all the sources of energy before any intervention on the machine.

Installation manual 9
The machines comply with the European Directive EMC (Electromagnetic Compatibil-
ity). They have been tested in laboratory and approved as such. It is so prohibited to
add wires or nonshielded electric cables in the cabinets, strands or cables' troughs.
Considering that the volume of the outer drum is superior to 150 litres, the standard
kept for the electric part is the IN 60204.
CAUTION
With AIDO(Automatic Inner Door Opening) option, Take care of the disc of the opening
system above your head. Risk of cutting with the edge of the disc!!
Take care also of the locking system on your side; risk of cutting with the edge of the
plate!!
CAUTION
When you put your hands into the drum, take care of the edge of the outer drum doors
on yours sides. Risk of cutting with the edge of the metal plate!!
CAUTION
The machine can work without the protective casing when the electric supply is not cut
off.
Interlock the main isolating switch with a padlock.
Close the steam or gas inlet valves.
IMPORTANT
Ensure that the machine is not loaded beyond its maximum capacity (70 kg (154 lb) for
WB6 70 ; 90 kg (198 lb) for WB6 90 and 110 kg (242 lb) for WB6 110).
An excessive load has consequences for the lifetime of the machine’s organs, as
follows:
• Premature deterioration and failure of the suspension elements (springs, shock
absorbers);
• Excessive fatigue of motorization elements (engine, belt);
• Rapid reduction of lifetime of drum bearings (rolling bearings);
• Opening and destruction of drum doors and tank doors during oil dehydration.
This is particularly important for your safety and that of others.
The consequence is an immediate cancellation of the warranty.

10 Installation manual
THINK OF THE ENVIRONMENT!
The use and handling of chemical products such as detergent, chlorine, acids, desca-
ling agents, etc may create hazards for health and environment ; the following precau-
tions should be taken:
• Do not breathe the dusts or steam;
• Avoid contact with skin or eyes (may cause burns);
• In case of important spillage, wear a protecting mask, gloves, and eye protectors;
• Handle with care;
• Consult the use and first aid advice on the packing;
• Do not dispose pure products in the environment.
WARNING
The use and handling of chemical products such as detergent, chlorine, acids, antilim-
ing agents etc... may create hazards for health and environment ; the following precau-
tions should be taken.
- Do not breathe the dusts or steam.
- Avoid contact with skin or eyes (may cause burns).
- In case of important spillage, wear a protecting mask, gloves, and eye protectors.
- Handle with care.
- Consult the use and first aid advice on the packings.
- Do not dispose pure products in the environment.

Installation manual 11
1.1 Symbols
Caution.
Caution, presence of dangerous current.
Read the instructions before using the machine.

12 Installation manual
1.2 Personal protection equipment
Given below is a summary table of the Personal Protection Equipment (PPE) to be used
during the various phases of the machine’s service life.
Phase Protection
garments
Safety
footwear
Gloves Glasses Ear protectors Mask Safety helmet
Transport XO
Handling XO
Unpacking XO
Installation X O
Normal use X X X X
Adjustments OX
Routine
cleaning OX X O
Extraordinary
cleaning OX X O
Maintenance OXO
Dismantling OXO
Scrapping OXO
Legend :X: PPE required ; O: PPE available or to be used if necessary.
Normal use : Safety footwear must be defined for a use on a wet floor. And use glasses
and gloves to manipulate chemical products.
1.3 Preliminary instructions
WARNING
Risk of jamming when opening the lower door for unloading
WARNING
Risk of jamming with trolley and lower door when opening (if trolley height = 900mm)

Installation manual 13
WARNING
Risk of the upper door being raised quickly on loading
WARNING
After the installation, Send back the commissionning form ,signed document, to Elec-
trolux to validate the warrantly of the product.

14 Installation manual
1.4 Data plate explanation
In this chapter, you will find the explanation of the different data input on the data plate of
your product.
• Commercial name : Usual name of your product ( i.e. WPB4700H).
• Type : Type of your product (you have the same on the Declaration of Conformity CE if
delivered with CE certification).
• Model : Model of your product (can be different of commercial name ) (i.e
WSBA6180H17 for commercial name WB6–20) .
• Serial Number : serial number of your product which indicate the week of the produc-
tion of your product (the first 4 digit indicate the year and the week of production)
and the plant where it has been produced (finish by 17)
• Product N°: Product number of your product.
• Date : The date of the end of manufacture of your product
• Capacity : for washer product, the maximum loaded weight of linen for your product (in
kg)(i..e. 70 kg for WPB4700H)
• Some technical data depending of the heating of your product : see list below :
• Some technical data depending of the voltage ordered.
the voltage looks like that 380–415V 3 50–60Hz
under this, you find the protection request for your product (i.e 16 A)
• Different logos are available on your data plate .
They represent the different certification obtained for your product
CE, EAC
ETL intertek for USA and Canada countries
• QR code : when you scan it, you will be able to obtain the full documentation for your
product (Complete installation and user manuals)
• Standardized protection index of your product : IP24D

Installation manual 15
Electrical heating :
• P.Max : maximum power installed of your product
• Power of the motorization in kW and its isolation class (F) .
• Heating power in W .

16 Installation manual
Steam heating :
Left side
• P.Max : maximum power installed of your product
• Power of the motorization in kW and its isolation class (F) .
• Heating power in W .
Right side
• P.Maxi. (kPa) maximum pressure
For additional information, do not hesitate to consult with our quality department.

Installation manual 17
1.5 Warranty terms and exclusions
If the purchase of this product includes warranty coverage, warranty is provided in line
with local regulations and subject to the product being installed and used for the purposes
as designed, and as described within the appropriate equipment documentation.
Warranty will be applicable where the customer has used only genuine spare parts and
has performed maintenance in accordance with Electrolux Professional user and mainte-
nance documentation made available in paper or electronic format.
Electrolux Professional strongly recommends using Electrolux Professional approved
cleaning, rinse and descaling agents to obtain optimal results and maintain product effi-
ciency over time.
The Electrolux Professional warranty does not cover:
• service trips cost to deliver and pick up the product;
• installation;
• training on how to use/operate;
• replacement (and/or supply) of wear and tear parts unless resulting from defects in ma-
terials or workmanship reported within one (1) week from the failure;
• correction of external wiring;
• correction of unauthorized repairs as well as any damages, failures and inefficiencies
caused by and/or resulting from;
– insufficient and/or abnormal capacity of the electrical systems (current/voltage/fre-
quency, including spikes and/or outages);
– inadequate or interrupted water supply, steam, air, gas (including impurities and/or
other that does not comply with the technical requirements for each appliance);
– plumbing parts, components or consumable cleaning products that are not ap-
proved by the manufacturer;
– customer’s negligence, misuse, abuse and/or non-compliance with the use and care
instructions detailed within the appropriate equipment documentation;
– improper or poor: installation, repair, maintenance (including tampering, modifica-
tions and repairs carried out by third parties not authorized third parties) and modifi-
cation of safety systems;
– Use of non-original components (e.g.: consumables, wear and tear, or spare parts);
– environment conditions provoking thermal (e.g. overheating/freezing) or chemical (e.
g. corrosion/oxidation) stress;
– foreign objects placed in- or connected to- the product;
– accidents or force majeure;
– transportation and handling, including scratches, dents, chips, and/or other damage
to the finish of the product, unless such damage results from defects in materials or
workmanship and is reported within one (1) week of delivery unless otherwise
agreed;
• product with original serial numbers that have been removed, altered or cannot be
readily determined;
• replacement of light bulbs, filters or any consumable parts;
• any accessories and software not approved or specified by Electrolux Professional.

18 Installation manual
Warranty does not include scheduled maintenance activities (including the parts required
for it) or the supply of cleaning agents unless specifically covered within any local agree-
ment, subject to local terms and conditions.
Check on Electrolux Professional website the list of authorized customer care.
2 Environmental information
Concerned by providing the end user with useful and necessary environmental information, we wish to precise:
• Data about energetic consumptions, wastes (atmospheric and liquid) and sound level are indicated in the para-
graph «Technical characteristics».
• Foreseeing its recycling, this machine is fully dismantable.
• This machine is free from any asbestos.
• In conformity with French regulations.
• In the other countries, we recommend that you comply with the legislation in force in the country where the ma-
chine is installed.
• In France, all owners of packing waste producing a weekly volume below 1100 litres can forward these to the local
collection and treatment department. If exceeding this volume, the owners of packing waste will ensure their valu-
ation by reuse, recycling or, any other action aiming at producing reusable materials or energy... or provide them
contractually to a certified intermediate authorised to transport, trade or broke waste.
Therefore, this forbid:
– land filling raw waste;
– open air burning or incineration without energy collection.
• Packaging of our machines are according with the french legislation related to environment requirements.
For additional information, do not hesitate to consult with our environmental department.
Scrapping of machine
When the machine is no longer to be used, it must be submitted to a recycling facility for destruction.
The majority of the components in the machine can be reused, but it also contains other materials that must be
taken care of in the correct way.
Therefore, never mix the machine or its parts with domestic waste as this may lead to health hazards or dam-
age to the environment.
3 Locking and tagging procedure
A red insert at the beginning of this instruction handbook schematically shows the locking and tagging procedure de-
scribed below. If you wish, you can detach this insert and display it close to the machine to remind maintenance per-
sonnel of the safety instructions.
Always respect items 2, 3 and 4 carefully before doing any repair or maintenance work on
the machine.

Installation manual 19
Put the main switch to Off
and lock the handle with a
padlock in one of the
three holes provided for
this purpose.
Close the stop valves for
the other supplies (steam,
gas, thermal fluid, com-
pressed air) to stop and
lock their handle with a
padlock.
Open the fixed protectors
(casings, doors) with the
key provided or a special
tool.
Do the maintenance.
Close and carefully lock the fixed protectors.
Unlock the stop valves and the main switch.

20 Installation manual
4 Handling
Important
It is obligatory that all these operations are undertaken by handling specialists.
Before any handling, check that the four transport locks fitted are still in place and well-tightened.
To do so, remove the side casings and check presence of four locks (B) and the down casings for the four locks (A).
Caution
To handle the machine, you must imperatively reassemble the transport bridles and dis engage the load cells
(proceed in reverse order or “remove of the transport locks fitted” )
4.1 Lifting with a fork-lift truck
Warning
You should never handle the machine in its longitudinal side (any other than shown on the drawing below) with a
fork-lift truck. Important risk of parts deterioration for those fixed under the machine.
This can be carried out from the front or back, and at the centre of the machine using forks with minimum length of
1.50 m (59”)
4.2 Lifting with handlings straps
Lifting in that case can only be done with handling straps (minimum capacity 3000 daN / 6600 lb) which bear weight
of the machine.