Electronics IP65T User manual

Product Guide
IP65T
IP65T/24V
today, tomorrow and in the future
mselectronics.co.uk
IP65 Rated Thermostat
energy saving controls

2
Issue 1.0
Product Overview
The IP65T utilises an IP65 rated polycarbonate enclosure with an embedded high accuracy
temperature sensor to control heating or air conditioning. A built-in M20 cable gland maintains the
IP65 rating when used with appropriate electrical cable.
The temperature setpoint is fully adjustable between +12°C and +26°C and the switching
hysteresis (di󰀨erential) can also be adjusted between 0.25°C and 4°C.
Product Wiring
1. IMPORTANT: ensure all electrical connections are isolated before commencing any work on the
unit.
2. Power to the thermostat is provided via the Live and Neutral input terminals labelled “L” and “N”
(230V AC, 50Hz). On the 24 volt product variant (“/24V”) the same terminals are used (24V AC or
DC) and are not polarity sensitive.
3. A voltage-free changeover relay output capable of switching loads of up to 10A, 250V AC (resistive)
is provided by the thermostat at the “NC, COM, NO” terminals. Connect to your application given
the following:
• The Common “COM” terminal is connected to the Normally Closed “NC” terminal when the
sensed temperature is above the selected temperature.
• Conversely, the “COM” terminal is connected to the Normally Open “NO” terminal when
the sensed temperature is below the selected temperature.
Figure 1 Typical wiring example

3Issue 1.0
Installation
1. IMPORTANT: ensure all electrical connections are isolated before commencing any work on the
unit.
2. Unscrew and remove the front of the enclosure which contains the electronics.
3. Mount the rear of the enclosure to the wall using the 4 pre-existing screw points. DO NOT drill
through the back of the enclosure as this will void the product IP rating.
4. Ensure best-practices are used when choosing a location for the thermostat so that optimal
thermostatic control is achieved. Do not mount near drafts, heaters, radiators, air conditioners, in
direct sunlight or any other place where the sensed temperature may be unnaturally inuenced. A
good mounting height is typically between 1m and 2m from the oor.
5. Pass the electrical cable through the cable gland then connect as shown in Figure 1 (or any suitably
appropriate form). Ensure the correct output terminals that are suitable to your application are
chosen.
6. Adjust the internal thumbwheels to suit the desired operational requirements (see below).
7. Screw the front of the enclosure back on then tighten the cable gland to seal against the cable.
Operation
1. IMPORTANT: ensure all electrical connections are isolated before commencing any work on the
unit.
2. Adjust the “Setpoint” dial to the temperature the area is to be regulated to (typically 20ºC).
3. Set the “Di󰀨erential” to the total temperature swing either side of the resulting setpoint that the
temperature is required to keep within (typically 1°C).
4. Example set-up:
Setpoint set to 20ºC, Di󰀨erential set to 1ºC.
The thermostat will maintain the temperature between 19.5ºC and 20.5ºC.
Technical Specication
Power supply: 220V - 240V AC 50Hz (live/neutral)
22V - 24V AC or DC (“/24V” variant only)
Output switch rating: 10A, 250V AC 50Hz (resistive)
Output switch type: Changeover relay (volt-free)
Temperature control: +12°C to +26°C
Temperature di󰀨erential: 0.25°C to 4°C
Sensor accuracy: ±0.2°C
Sensor drift: 0.15°C over 5 years
Guarantee: 5 Years
Weight: 190g
Dimensions: 82mm x 80mm x 55mm

e: [e-mail]
t: 0333 666 1176 f: 0333 666 1436
mselectronics.co.uk
Follow us on twitter: @mselec
MS Electronics reserves the right to alter or change this specification without prior notice.
IMPORTANT INSTALLATION NOTICE
The installation of this product should be carried out in accordance with the latest IEE wiring
regulations and all wiring completed by a qualified electrician.
Technical Support
For further help or information on this and the other products in the MS Electronics range
visit www.mselectronics.co.uk or call 0333 666 1176.
Alternatively, email [e-mail]
Additional copies of this product guide can be downloaded from our website.
Product Warranty
MS Electronics guarantees all their products against manufacturing defects for
5 years from the purchase date. If your product is found to be faulty, MS Electronics will,
at their discretion, repair or replace the product free of charge.
Note
Any modification or damage to the outer casing of the product, as well as any
damage to the product due to abuse or incorrect wiring may invalidate the guarantee.
energy saving controls