Element P42K User manual

PA2K User Manual I Page 1of 104
2D Barcode Reader User Guide

PA2K User Manual I Page 2of 104
Table of Contents
1 Getting Started
1.1 About This Guide..........................................................................................................................................4
1.2 Barcode Scanning .........................................................................................................................................4
1.3 Factory Defaults............................................................................................................................................4
1.4 Firmware Version Number .........................................................................................................................4
2.1 RS-232 Interface ...........................................................................................................................................5
2.2 Baud Rate.....................................................................................................................................................6
2.3 Data Bit & Parity Check & Stop Bit................................................................................................................8
2.4 XON/XOFF ...................................................................................................................................................8
2.5 Accepting RS-232 Commands ......................................................................................................................9
2.6 USB HID-KB.............................................................................................................................................10
2.7 USB Country Keyboard Types .....................................................................................................................11
2.8 Convert Case ..........................................................................................................................................17
2.9 Transmission speed.....................................................................................................................................17
2.10 Function Code Transmit ............................................................................................................................18
2.11 USB COM Port Emulation.........................................................................................................................18
3.1 Trigger Mode..............................................................................................................................................19
3.2 Presentation Mode .....................................................................................................................................20
3.3 Read Mode .................................................................................................................................................20
3.4 Illumination Lights.......................................................................................................................................21
3.5 Illumination-Presentation ............................................................................................................................22
3.6 Idle Illumination-Presentation .....................................................................................................................22
3.7 LED Idle State-Presentation ........................................................................................................................23
3.8 Continue-Scan Presentation Mode .............................................................................................................24
3.9 Power-Up Beeper........................................................................................................................................24
3.10 Good Read Beeper ...................................................................................................................................25
3.11 Good Read Beeper Volume.......................................................................................................................26
3.12 Good Read Beeper Duration.....................................................................................................................26
3.13 Good Read Beeper Tone...........................................................................................................................27
3.9 Good-read Delay ........................................................................................................................................28
3.10 Reread Delay.............................................................................................................................................30

PA2K User Manual I Page 3of 104
4.1 General Configuration................................................................................................................................31
4.2 Add Prefix ..................................................................................................................................................33
4.3 Add Suffix ...............................................................................................................................................34
4.4 Clear All Prefix and Suffix ...........................................................................................................................34
5.1 General Setting...........................................................................................................................................35
5.2 1D Symbologies..........................................................................................................................................35
5.2.2 EAN-8...................................................................................................................................................37
5.2.3 EAN-13.................................................................................................................................................42
5.2.4 UPC-E...................................................................................................................................................46
5.2.5 UPC-A ..................................................................................................................................................51
5.2.10 Coda Bar ............................................................................................................................................66
5.2.12 GS1-128..........................................................................................................................................71
5.2.13 MSI..................................................................................................................................................73
5.2.15 Telepen...............................................................................................................................................77
5.3 2D Symbologies..........................................................................................................................................79
5.3.2 QR Code ..............................................................................................................................................82
5.3.3 QR Code URL Link................................................................................................................................84
5.3.4 Data Matrix...........................................................................................................................................85
5.3.5 Maxi code.............................................................................................................................................87
5.3.6 Aztec ....................................................................................................................................................89
5.3.7 Hanxin...............................................................................................................................................91
6.1 Appendix 1: AIM ID Table...........................................................................................................................93
6.2 Appendix 2: ASCII Table .............................................................................................................................97
6.3 Appendix 3: Digit Barcodes......................................................................................................................104

PA2K User Manual I Page 4of 104
1.1 About This Guide
This guide provides programming instructions for the Element 2D Barcoder Reader. Users can
configure the 2D Barcoder Reader by scanning the programming barcodes included in this manual.
1.2 Barcode Scanning
Powered by area-imaging technology and 2D Barcoder Reader patented “Hercules” technology, the
2D Barcoder Reader features fast scanning and decoding accuracy. Barcodes rotated at any angle can still be
read with ease. When scanning a barcode, simply center the aiming beam or pattern projected by the 2D
Barcoder Reader over the barcode.
1.3 Factory Defaults
Scanning the following barcode can restore the engine to the factory defaults.
Note: Use this feature with discretion.
Restore All Factory Defaults
1.4 Firmware Version Number
Scanning the barcode below can display the firmware version number.
Display The Firmware Version Number

PA2K User Manual I Page 5of 104
The 2D Barcoder Reader provides a RS-232 interface and a USB interface to communicate with the host device.
The host device can receive scanned data and send commands to control the engine or to access/alter the
configuration information of the engine via the RS-232 or USB interface.
2.1 RS-232 Interface
Serial communication interface is usually used when connecting the engine to a host device (like PC, POS).
However, to ensure smooth communication and accuracy of data, you need to set communication
parameters (including baud rate, parity check, data bit and stop bit) to match the host device.
The serial communication interface provided by the engine is based on RS-level signals.
Default serial communication parameters are listed below. Make sure all parameters match the host
requirements.
Parameter
Factory Default
Serial Communication
Standard RS-232
Baud Rate
115200
Parity Check
None
Data Bits
8
Stop Bits
1
Hardware Flow Control
None
Note: scanners support Auto-Cable functionwhich can be switched 232 interface automatically
when connecting with 232cable.
2 Communication Interfaces

PA2K User Manual I Page 6of 104
2.2 Baud Rate
Baud rate is the number of bits of data transmitted per second. Set the baud rate to match the Host
requirements.
2400
9600
38400
*115200

PA2K User Manual I Page 7of 104
4800
19200
57600

PA2K User Manual I Page 8of 104
2.3 Data Bit &Parity Check &Stop Bit
*None Parity /8 Data Bits/1 Stop Bit
Even Parity /7 Data Bits/1 Stop Bit
Odd Parity /7 Data Bits/1 Stop Bit
2.4 XON/XOFF
The scanner stops sending data when the host sends the XOFF character (hex 13) to it. To
resume transmission, the host sends the XON character (hex 11)
*XON/XOFF Disable
XON/XOFF Enable

PA2K User Manual I Page 9of 104
2.5 Accepting RS-232 Commands
*Disable
Enable
Commands
ASCII
HEX
Disable Scanner
D
0x44
Enable Scanner
E
0x45
For the scanner, it can accept serial host commands. If you wish to enable/disable scanner by using
commands, scan the enable barcode. Host commands for other interfaces are also available.

PA2K User Manual I Page 10 of 104
2.6 USB HID-KB
When you connect the engine to the Host via aUSB connection, you can enable the USB HID-KB feature
by scanning the barcode below. Then engine’s transmission will be simulated as USB keyboard input. The
Host receives keystrokes on the virtual keyboard. It works on a Plug and Play basis and no driver is required.
USB HID-KB