ELICA EPR628SS Datasheet

Installation Instructions Guide
Instructions d’installation Guide
Guía de Instrucciones para Instalación
READ AND SAVE THESE INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION GUIDE
LEA Y GUARDE ESTAS INSTRUCCIONES
Model: EPR628SS
English p. 3
Français p. 14
Español p. 25
Model: EAS428SS
LI31MA

3
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
ɷUse this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
ɷBefore servicing or cleaning the unit, switch power off at
service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When
the service disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag to the
service panel.
ɷInstallation work and electrical wiring must be done by
 TXDOL¿HGSHUVRQVLQDFFRUGDQFHZLWKDOODSSOLFDEOHFRGHV
 DQGVWDQGDUGVLQFOXGLQJ¿UHUDWHGFRQVWUXFWLRQ
ɷ6XI¿FLHQWDLULVQHHGHGIRUSURSHUFRPEXVWLRQDQG
 H[KDXVWLQJRIJDVHVWKURXJKWKHÀXHFKLPQH\RIIXHO
burning equipment to prevent backdrafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire
 3URWHFWLRQ$VVRFLDWLRQ1)3$WKH$PHULFDQ6RFLHW\IRU
Heating, Refrigeration and Air Conditioning Engineers
 $6+5$(DQGWKHORFDOFRGHDXWKRULWLHV
ɷWhen cutting or drilling into wall or ceiling; do not damage
electrical wiring and other utilities.
ɷDucted fans must always be vented outdoors.
CAUTION: For general ventilating use only. Do not use to
exhaust hazardous or explosive materials and vapors.
CAUTION: 7RUHGXFHULVNRI¿UHDQGWRSURSHUO\H[KDXVWDLU
EHVXUHWRGXFWDLURXWVLGHGRQRWYHQWH[KDXVWDLULQWR
spaces within walls or ceilings, attics or into crawl spaces, or
garages.
WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF A RANGE TOP
GREASE FIRE:
ɷNever leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
ɷAlways turn hood ON when cooking at high heat or when
 ÀDPEHLQJIRRGLH&UHSHV6X]HWWH&KHUULHV-XELOHH
 3HSSHUFRUQ%HHI)ODPEp
ɷClean ventilating fans frequently. Grease should not be
 DOORZHGWRDFFXPXODWHRQIDQRU¿OWHU
ɷUse proper pan size. Always use cookware appropriate for
the size of the surface element.
WARNING: 725('8&(7+(5,6.2),1-85<72
PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:a
ɷ6027+(5)/$0(6ZLWKDFORVH¿WWLQJOLGFRRNLHVKHHWRU
metal tray, then turn off the burner. BE CAREFUL TO
 35(9(17%8516,IWKHÀDPHVGRQRWJRRXW
immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
ɷ1(9(53,&.83$)/$0,1*3$1\RXPD\JHWEXUQHG
ɷ'212786(:$7(5LQFOXGLQJZHWGLVKFORWKVRUWRZHOV
a violent steam explosion will result.
ɷUse an extinguisher ONLY if:
<RXNQRZ\RXKDYHDFODVV$%&H[WLQJXLVKHUDQG\RX
already know how to operate it.
 ±7KH¿UHLVVPDOODQGFRQWDLQHGLQWKHDUHDZKHUHLW
started.
 ±7KH¿UHGHSDUWPHQWLVEHLQJFDOOHG
 ±<RXFDQ¿JKWWKH¿UHZLWK\RXUEDFNWRDQH[LW
aBased on “Kitchen Fire Safety Tips” published by NFPA.
WARNING: 7RUHGXFHWKHULVNRI¿UHRUHOHFWULFDOVKRFN
 GRQRWXVHWKLVIDQZLWKDQ\VROLGVWDWHVSHHGFRQWURO
device.
APPROVED FOR RESIDENTIAL APPLIANCES
FOR RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical
Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for
the owner.
OWNER: Please retain these instructions for future
reference.
Safety Warning:Turn off power circuit at service panel and lock
out panel before wiring this appliance.
Requirement 120 VAC, 60 Hz. 15 or 20 A Branch Circuit
Table of Contents
Important Safety Notice .......................................................... 3
Tools and parts ........................................................................ 4
Location Requirements ...................................................... 4
Product Dimensions ........................................................... 4
Venting Requirements ........................................................ 5
Venting Methods ................................................................ 6
Calculating Vent System Length ........................................ 6
Electrical Requirements...........................................................6
Installation Instructions .......................................................... 7
Prepare Location.................................................................7
Install range hood.....................................................................9
Connect the Vent System....................................................10
Complete Installation...........................................................10
Range Hood Use....................................................................... 11
Range Hood Care......................................................................11
Available Accessories.............................................................. 12
Warranty.....................................................................................13

4
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed (all models)
ŶLevel
ŶDrill
Ŷ ï»8´PPGULOOELW
ŶPencil
ŶPliers
ŶTape measure or ruler
ŶCaulking gun and weatherproof caulking compound
Ŷ )ODWEODGHVFUHZGULYHU
ŶPhillips screwdriver
ŶSaber or keyhole saw
ŶMetal snips
ŶVent clamps
Parts Supplied
Remove parts from packages. Check that all parts are included.
Ŷ ´[´[FPIDFHSDQHO
ŶDamper
Ŷ :LQFDQGHVFHQWODPSVRQO\PRGHO($666
Ŷ :KDORJHQODPSVRQO\PRGHO(3566
Ŷ 0HWDOJUHDVH¿OWHUV
Ŷ 0RXQWLQJEUDFNHWV
Ŷ 0HWDOVSDFHUVIRUXVHZKHQFDELQHWGHSWKLVJUHDWHU
 WKDQ´
ŶHardware package. Includes:
 Installation Instructions and Use and Care Guide
 PHWDOZDVKHUV
 SODVWLFZDVKHUV
 [PPZRRGVFUHZV
 [PPPDFKLQHVFUHZV
 [PPÀDWKHDGVKHHWPHWDOVFUHZV
 [PPVKHHWPHWDOVFUHZV
 [PPVKHHWPHWDOVFUHZV
 T10 TORX®† adapter
Parts needed
Ŷ ´FPURXQGPHWDOYHQWV\VWHP
†®TORX is a registered trademark of Saturn Fasteners, Inc.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
+DYHDTXDOL¿HGWHFKQLFLDQLQVWDOOWKHUDQJHKRRG,WLVWKH
installer’s responsibility to comply with installation clearances
VSHFL¿HGRQWKHPRGHOVHULDOUDWLQJSODWH7KHPRGHOVHULDOUDWLQJ
SODWHLVORFDWHGLQVLGHWKHOLQHUEHKLQGWKH¿OWHURQWKHOHIWZDOORI
the range hood.
Range hood location should be away from strong draft areas,
such as windows, doors, and strong heating vents.Cabinet open
ing dimensions that are shown must be used. Given dimensions
SURYLGHPLQLPXPFOHDUDQFH&RQVXOW\RXUFRRNWRSUDQJHPDQX
facturer installation instructions before making any cutouts.
Grounded electrical outlet is required. See “Electrical Require
ments” section.
The range hood is factory set for vented installations through the
URRIRUZDOO)RUQRQYHQWHGUHFLUFXODWLQJLQVWDOODWLRQVVHH³1RQ
9HQWHGUHFLUFXODWLQJ,QVWDOODWLRQ7KURXJKWKH6RI¿W&DELQHW´LQ
the “Prepare Location” section. Recirculation Kit Part is available
from your dealer or an authorized parts distributor. All openings
in ceiling and wall where range hood will be installed must be
sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
&)53DUWIRUPHUO\WKH)HGHUDO6WDQGDUGIRU0RELOH+RPH
&RQVWUXFWLRQDQG6DIHW\WLWOH+8'3DUWRUZKHQVXFK
standard is not applicable, the standard for Manufactured Home
,QVWDOODWLRQ0DQXIDFWXUHG+RPH6LWHV&RPPXQLWLHVDQG
6HWXSV$16,$1)3$$RUODWHVWHGLWLRQRUZLWKORFDO
codes.
Product Dimensions
I*
I*
,0HWDOOLFVSDFHUV
Spacers has to be installed
and used when cabinet depth
is greater than 12”.
EAS428SS / EPR628SS range hood models
Dimension
DIM A 281»4´FP
DIM B ´FP
DIM C ǩ´FP
DIM D ô´FP
DIM E ò´FP
DIM F 5»16´FP
DIM G 14 9»16´FP
DIM H ´FP
DIM I ò´FP

5
Installation Clearances
$´FPPLQXSSHU
cabinet height
%´FP
cabinet opening width*
&´FPPLQ´FP
suggested max. bottom of
cabinet to cooking surface
'´FPFDELQHW
opening depth*
(´FPPLQFOHDUDQFH
upper cabinet to countertop
)´FPEDVHFDELQHW
height
For gas range installation: Mount this hood so that the bottom
HGJHLVDWPLQLPXP´FPDERYHWKHFRRNLQJVXUIDFH
For electric range installation: mount this hood so that the bottom
LVQRWOHVVWKDQ´FP
127(7KLVUDQJHKRRGLVVHWWR´FPFDELQHWZLGWK[
´FPGHHSFDELQHWV
VENTING REQUIREMENTS
ŶVent system must terminate to the outdoors, except for no
 YHQWHGUHFLUFXODWLQJLQVWDOODWLRQV
ŶDo not terminate the vent system in an attic or other enclosed
area.
Ŷ 'RQRWXVHD´FPODXQGU\W\SHZDOOFDS
ŶUse metal vent only. A rigid metal vent is recommended.
Plastic or metal foil vent is not recommended.
ŶThe length of the vent system and number of elbows should
 EHNHSWWRDPLQLPXPWRSURYLGHHI¿FLHQWSHUIRUPDQFH
)RUWKHPRVWHI¿FLHQWDQGTXLHWRSHUDWLRQ
ŶUse no more than three 90° elbows.
Ŷ 0DNHVXUHWKHUHLVDPLQLPXPRI´FPRIVWUDLJKW
vent between the elbows if more than 1 elbow is used.
ŶDo not install 2 elbows together.
ŶThe vent system must have a damper.
ŶUse clamps to seal all joints in the vent system.
ŶUse caulking to seal exterior wall or roof opening around the
cap.
ŶThe size of the vent should be uniform.
Cold weather installations
An additional back draft damper should be installed to minimize
EDFNZDUGFROGDLUÀRZDQGDWKHUPDOEUHDNVKRXOGEHLQVWDOOHGWR
minimize conduction of outside temperatures as part of the vent
system. The damper should be on the cold air side of the thermal
break.
The break should be as close as possible to where the vent
system enters the heated portion of the house.
Makeup air
Local building codes may require the use of makeup air systems
ZKHQXVLQJYHQWLODWLRQV\VWHPVZLWKJUHDWHUWKDQVSHFL¿HG&)0
RIDLUPRYHPHQW7KHVSHFL¿HG&)0YDULHVIURPORFDOHWRORFDOH
&RQVXOW\RXU+9$&SURIHVVLRQDOIRUVSHFL¿FUHTXLUHPHQWVLQ\RXU
area.

6
Venting Methods
This range hood is factory set for venting through the roof or
through the wall. You can apply the recirculating venting method
by purchasing the Recirculation Kit.
The vent system needed for installation is not included.
$´FPURXQGYHQWV\VWHPLVUHFRPPHQGHG
Roof Venting
$´FPYHQW
through the roof
B. Roof cap
Wall Venting
$´FPYHQW
through the wall
B. Wall cap
Recirculating
$´FPYHQW
through the cabinet
B. Round recirculating grid
Calculating Vent System Length
7KHUHFRPPHQGHGYHQWV\VWHPLV´FPURXQGYHQWZLWKD
PD[LPXPOHQJWKRIIWP)RUWKHEHVWSHUIRUPDQFHXVH
no more than three 90° elbows.
To calculate the length of the system, add the equivalent feet
PHWHUVIRUHDFKRIWKHYHQWSLHFHVXVHGLQWKHV\VWHP
Vent Piece 6” (15.2 cm)
45° elbow 2.5 ft
P
90° elbow 5.0 ft
P
Example Vent System
90° elbow Wall cap
IWP
IWP
Maximum Recommended Length = 35 ft (10.7 m)
HOERZ IWP
ZDOOFDS IWP
IWPVWUDLJKW IWP
Length of 6” (15.2 cm) system = 14.0 ft (4.3m)
WARNING
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
GHDWK¿UHRUHOHFWULFDOVKRFN
IMPORTANT: The range hood must be electrically grounded in
accordance with local codes and ordinances, or in the absence
RIORFDOFRGHVZLWKWKH1DWLRQDO(OHFWULFDO&RGH$16,1)3$
ODWHVWHGLWLRQRU&DQDGLDQ(OHFWULFDO&RGH&6$&
1R0ODWHVWHGLWLRQ
If codes permit and a separate ground wire is used, it is
UHFRPPHQGHGWKDWDTXDOL¿HGHOHFWULFDOLQVWDOOHUGHWHUPLQHWKDW
the ground path is adequate.
Electrical Requirements
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
4XLQF\0$
CSA International
8501 East Pleasant Valley Road
&OHYHODQG2KLR
Ŷ $  YROW  +] $& RQO\  RU DPS IXVHG HOHFWULFDO
 FLUFXLW LV UHTXLUHG$ WLPHGHOD\ IXVH RU FLUFXLW EUHDNHU LV DOVR
recommended. It is recommended that a separate circuit
serving only this range hood be provided.
ŶThis range hood is equipped with a power supply cord having
a 3 prong grounding plug.
ŶTo minimize possible shock hazard, the cord must be
 SOXJJHG LQWR D PDWLQJ  SURQJ JURXQGLQJW\SH RXWOHW
grounded in accordance with local codes and ordinances. If a
mating outlet is not available, it is the personal responsibility
and obligation of the customer to have the properly grounded
 RXWOHWLQVWDOOHGE\DTXDOL¿HGHOHFWULFLDQ

7
Installation Instructions
ŶThe grounded 3 prong outlet is to be located inside the
cabinet above the range hood at a maximum distance of
337»16´  FP IURP ZKHUH WKH SRZHU FRUG H[LWV WKH KRRG
The grounded 3 prong outlet must be accessible after
installation of the range hood. See illustration.
33 7»16FP
GROUNDING INSTRUCTIONS
Ŷ )RUDJURXQGHGFRUGFRQQHFWHGUDQJHKRRG
This range hood must be grounded. In the event of an
electrical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current.
This range hood is equipped with a cord having a grounding
wire with a grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded.
WARNING: Improper grounding can result in a risk of electric
shock.
&RQVXOWDTXDOL¿HGHOHFWULFLDQLIWKHJURXQGLQJLQVWUXFWLRQVDUH
not completely understood, or if doubt exists as to whether
the range hood is properly grounded.
Do not use an extension cord. If the power supply cord is too
VKRUWKDYHDTXDOL¿HGHOHFWULFLDQLQVWDOODQRXWOHWQHDUWKH
range hood.
SAVE THESE INSTRUCTIONS
Prepare Location
ŶIt is recommended that the vent system be installed before
the range hood is installed.
ŶBefore making cutouts, make sure there is proper clearance
 ZLWKLQWKHFHLOLQJRUZDOOIRUYHQW¿WWLQJV
ŶMaking the cutout to the bottom of the cabinet may be easier
to do prior to mounting the cabinet to the wall.
1. Disconnect power.
2. Determine which venting method to use: roof, wall, or non
vented.
3. 6HOHFWDÀDWVXUIDFHIRUDVVHPEOLQJWKHUDQJHKRRG3ODFH
covering over that surface.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
range hood.
Failure to do so can result in back or other injury.
4. Using 2 or more people, lift range hood onto covered surface
Range Hood Cabinet Cutout
1. Use a saber saw or keyhole saw to cut out the cabinet
bottom inside the cabinet frame.
NOTE:)UDPHOHVVW\SHFDELQHWVUHTXLUHô´FPIURQWOLS
LQWKHFDELQHWERWWRP$ô´FPWKLFN¿OOHUVWULSQRW
VXSSOLHGPD\EHUHTXLUHGIRUVRPHW\SHVRIFDELQHWV6HH
6WHSLQWKH³,QVWDOO5DQJH+RRG´VHFWLRQ
Cut out dimensions (without spacers)
283»8´FP
107»8”
FP
3»4”
1»2”
A. Bottom of cabinet cutout
2. Complete cabinet preparation following the instructions for
your type of venting. Determine venting cutout locations and
 FXWRXWYHQWRSHQLQJVLQWKHFDELQHWVZDOOVDQGRUVRI¿W

8
Venting Outside Through the Roof
1. Measure and mark the lines as shown. Use a saber saw or
keyhole saw to cut an opening through the top of the cabinet
and the roof for the vent.
A
B* C
D
A. Cutout
%ó´FP
C. 7¾´FPFHQWHUOLQHWRFDELQHWIURQW
D. Centerline
127()RU´FPKLJKFDELQHWVDó´GHHS[´ZLGH
FP[FPUHFWDQJXODURSHQLQJLQWKHFDELQHWWRSLV
required for damper transition clearance.
Venting Outside Through the Wall
1. ,QVWDOOWKH´FPYHQWWUDQVLWLRQWRWKHWRSRIWKHUDQJH
hood liner using two 3.5 x 9.5 mm screws. Assemble the vent
 GXFWWKDW\RXZLOOXVHRYHUWKH´FPYHQWWUDQVLWLRQ
2. Measure from the bottom of the range hood liner to the
 KRUL]RQWDOFHQWHUOLQHRIWKHYHQWRSHQLQJ$
A
B
C
A. Measurement A
B. Horizontal centerline of vent opening
C. Range hood liner
3. Remove the vent duct from the range hood liner.
Transfer measurement A to the cabinet back wall. Measure
from the underside of the cabinet.
4. Mark the cutout as shown. Use a saber saw or keyhole saw to
cut a round opening through the back of the cabinet and the
exterior wall for the vent. Go to Step 3.
A
B
C
A. Measurement A
B. Centerline
&ó´FPURXQG
cutout
Non-Vented (recirculating) Installation Through the
6RI¿W&DELQHW
E
A
B
G
D
F
H
I
A
B
G
F
C
D
E
A. Ceiling
B. Vent cover
C. Soffit
'´FPYHQW
E. Range hood
F. Cabinet
G.Wall
+´FPPLQFDELQHWKHLJKW
,´FPPLQYHQWFRYHUKHLJKW
1. 0HDVXUHDQGPDUNWKHFHQWHUOLQHRIWKHFDELQHWWRWKHVRI¿W
above.
2. Measure from the bottom of the cabinet to the centerline of
 WKHZKHUHWKHYHQWZLOOFRPHWKURXJKWKHVRI¿W0DUNWKH
location and use a saber saw or keyhole saw to cut a 5¾”
 FPKROHIRUWKHYHQWFRYHU
AB
A. Vent cover
B. Centerline
127()RU´FPKLJKFDELQHWVDó´GHHS[´ZLGH
FP[FPUHFWDQJXODURSHQLQJLQWKHFDELQHWWRSLV
required for damper transition clearance.
Measure and mark the centerline location for the cutout in the
cabinet top. Use a saber saw or keyhole saw to cut an
opening for the vent.

9
ABC
D
A. Cutout
B. See chart below
C. 7¾´FPFHQWHU
line to cabinet front
D. Centerline
Cabinet Height Hole Shape and Size
´FP $ó´GHHS[´ZLGHFP[FP
rectangular opening in the cabinet top is
required for damper transition clearance.
Complete Preparation
 ,IQRW\HWDWWDFKHGLQVWDOOWKH´FPYHQWWUDQVLWLRQWKH
top of the range hood liner using two 3.5 x 9.5 mm screws.
 /RFDWHVLGHPRXQWLQJEUDFNHWÀXVKFPWRWKHERWWRPRIWKH
cabinet side and against the inside of the front cabinet face.
Orient the bracket depending on the width of your cabinet as
 GHSLFWHGLQWKHGLDJUDPVEHORZ'ULOOǩ´PPSLORWKROHVLQ
6 places, attach a bracket using three 4.5 x 13 mm screws to
each side of the cabinet, and tighten. Additional washers in
hardware package are supplied as spacers for cabinet walls
 WKLQQHUWKDQò´PP
%UDFNHW2ULHQWDWLRQIRU´FP&DELQHW
A
B
C
D
$´FPFDELQHW
%6FUHZV[PP
&:DVKHUVRSWLRQDO
'0RXQWLQJEUDFNHWSRVLWLRQIRU´>FP@FDELQHW
Move the bracket 6»16´FPIURPWKHERWWRP
side of the cabinet
3. Install the vent system according to the method needed.
Use caulking to seal the exterior wall or roof opening.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
range hood.
Failure to do so can result in back or other injury.
1. Using 2 or more people, lift the hood liner into its mounted
location. Attach with four 4.2 x 19 mm screws into the slotted
openings. Do not tighten screws.
A
B
C
A.Cabinet
B.Hood liner canopy assembly
&6FUHZV[PP
2. Center the canopy in the cabinet. Align the bottom of the
canopy with the bottom of the cabinet. Install four 4.2 x 19 mm
screws into the round mounting plate openings and tighten all
 PRXQWLQJVFUHZV
3. 5HPRYHWKHPHWDOJUHDVH¿OWHUVIURPWKHIDFHSDQHO6HHWKH
“Range Hood Care” section.
Attach the face plate to the hood insert.
NOTE: If cabinet depth is greater than 12”, it is recommended
 WKDWWKHWZR´PHWDOVSDFHUVDUHLQVWDOOHG
Install to front and rear sides of the face plate with 3.5 x 9.5
mm screws as shown in drawing.
C
A
C
B
A.Face Panel
B.Front and rear spacer
&6FUHZV[PP
Install Range Hood

10
B
C
D
A
$6FUHZV[PPIODWKHDG
%)DFHSODWH´[´>FP[FP@VKRZQ
&&DELQHW´[´>FP[FP@VKRZQ
'6FUHZV[PPWUXVVKHDG
For cabinet size - 30” x 12” (76.2 cm x 30.5 cm)
Attach the 281»4” x 10 ¾”FP[FPIDFHSDQHOVXSSOLHG
ZLWKUDQJHKRRGWRWKHKRRGOLQHUXVLQJIRXU[PP
ÀDWKHDGVFUHZVDQGWZR[PPWUXVVKHDGVFUHZV
Tighten to secure.
Connect the lamp electrical connector.
Connect the Vent System
Vented Installations
1. Connect the vent system to the range hood vent opening.
Seal the connection with clamps.
Non-Vented (recirculating) Installations
1. Connect the vent system to the range hood vent opening.
Seal the connection with clamps.
2. ,QVWDOOFKDUFRDO¿OWHUV6HHWKH³$YDLODEOHDFFHVRULHV´VHFWLRQ
Complete Installation
1. 5HSODFHJUHDVH¿OWHUV6HHWKH³5DQJH+RRG&DUH´VHFWLRQ
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
GHDWK¿UHRUHOHFWULFDOVKRFN
2. 3OXJSURQJSRZHUFRUGLQWRDJURXQGHGSURQJRXWOHW
located inside the cabinet above the range hood.
3. Check the operation of the range hood fan and light. See
“Range Hood Use” section.
If range hood does not operate, check to see whether a
circuit breaker has tripped or a household fuse has blown.
Disconnect power and check wiring connections.
NOTE:7RJHWWKHPRVWHI¿FLHQWXVHIURP\RXUQHZUDQJHKRRG
read the “Range Hood Use” section.

11
Range Hood Use
The range hood is designed to remove smoke, cooking vapors
and odors from the cooktop area. For best results, start the hood
before cooking and allow it to operate several minutes after the
cooking is complete to clear all smoke and odors from the
kitchen.
The hood controls are located on the center of the front of the
range hood liner.
D
C
A
B
A. Blower and light controls
B. Grease filter
C. Grease filter handle
'+DORJHQRU,QFDQGHVFHQWODPSVGHSHQGLQJRIKRRGPRGHO
Range Hood Controls
A B C D
$2Q2IIOLJKWEXWWRQ
B. Blower off and speed minimum button
C. Blower speed medium button
D. Blower speed maximum button
Operating the Light
7KH2Q2IIOLJKWEXWWRQFRQWUROVDOOOLJKWV3UHVVRQFHIRU2QDQG
again for Off.
Operating the Blower
The BLOWER SPEED buttons turn the blower on and control the
blower speed and sound level for quiet operation. The speed can
be changed anytime during fan operation by pressing the desired
blower speed button.
Press the BLOWER OFF button a second time to turn off the
blower.
Range Hood Care
Range Hood Controls
,03257$17&OHDQWKHKRRGDQGJUHDVH¿OWHUVIUHTXHQWO\
DFFRUGLQJWRWKHIROORZLQJLQVWUXFWLRQV5HSODFHJUHDVH¿OWHUV
before operating hood.
Exterior Surfaces:
To avoid damage to the exterior surface, do not use steel wool or
VRDS¿OOHGVFRXULQJSDGV
Always wipe dry to avoid water marks.
Cleaning Method:
Ŷ /LTXLGGHWHUJHQWVRDSDQGZDWHURUDOOSXUSRVHFOHDQVHU
ŶWipe with damp soft cloth or nonabrasive sponge, then rinse
with clean water and wipe dry.
Metal Grease Filter
7KH¿OWHUVVKRXOGEHZDVKHGIUHTXHQWO\3ODFHPHWDO¿OWHUVLQ
dishwasher or hot detergent solution to clean.
/HW¿OWHUGU\WKRURXJKO\EHIRUHUHSODFLQJLW
Turn off fan and lights. Allow lamps to cool.
1. 5HPRYHHDFK¿OWHUE\SXOOLQJWKHVSULQJUHOHDVHKDQGOHDQG
 WKHQSXOOLQJGRZQWKH¿OWHU
A
A. EPR628SS model spring release handle
A
A. EAS428SS model Spring release handle
2. :DVKPHWDO¿OWHUVDVQHHGHGLQGLVKZDVKHURUKRWGHWHUJHQW
solution.
3. 5HLQVWDOOWKH¿OWHUE\PDNLQJVXUHWKHVSULQJUHOHDVHKDQGOHV
 DUHWRZDUGWKHIURQW,QVHUWPHWDOJUHDVH¿OWHULQWRXSSHU
track.
4. Pull the spring release handle down.
5. 3XVKXSRQPHWDO¿OWHUDQGUHOHDVHKDQGOHWRODWFKLQWRSODFH
6. 5HSHDWVWHSVIRUWKHRWKHU¿OWHU

12
Replacing the halogen lamp (EPR628SS models)
CAUTION: Before replacing the lamps, disconnect power off
to prevent from being switched on accidentally.
7XUQRIIWKHUDQJHKRRGDQGDOORZWKHKDORJHQLQFDQGHVFHQW
lamp to cool. To avoid damage or decreasing the life of the new
EXOEGRQRWWRXFKEXOEZLWKEDUH¿QJHUV5HSODFHEXOEXVLQJ
tissue or wearing cotton gloves to handle bulb.
If new lamps do not operate, make sure the lamps are inserted
correctly before calling service.
1. Disconnect power.
2. 8VHDÀDWEODGHVFUHZGULYHUDQGJHQWO\SU\WKHOLJKWFRYHU
loose.
3. 5HPRYHWKHODPSDQGUHSODFHZLWKDYROWZDWW
 PD[LPXPKDORJHQODPSPDGHIRUD*EDVH
4. Replace the light cover.
5. Reconnect power.
Replacing the incandescent lamps (EAS428SS models)
1. Disconnect power.
2. Use a Phillips # 2 screw driver to remove the lamp cover.
Remove it carefully from its housing.
3. 5HPRYHWKHGDPDJHGODPSEXOEWXUQFRXQWHUFORFNZLVHDQG
replace it with a new bulb. E12 Philips Lamp 120V, 40W.
Reconnect power.
Available Accessories
Recirculating Kit
If it is not possible to vent cooking fumes and vapors to the
RXWVLGHWKHUDQJHKRRGFDQEHXVHGLQWKHQRQYHQWHG
UHFLUFXODWLQJYHUVLRQXVLQJDFKDUFRDO¿OWHU5HFLUFXODWLRQ.LW
model number EXXRCK10 is available from the dealer or an
authorized parts distributor.
E
A
B
G
D
F
H
I
A
B
G
F
C
D
E
A. Ceiling
B. Vent cover
C. Soffit
'´FPYHQW
E. Range hood
F. Cabinet
G.Wall
+´FPPLQFDELQHWKHLJKW
,´FPPLQYHQWFRYHUKHLJKW
NOTE:´FPKLJKFDELQHWVZLWKRXWDVRI¿WPD\DOORZWKH
6” vent and vent cover to be seen.
1. Cover the grill that protects the suction motor with the carbon
 ¿OWHUVRWKDWWKHVORWVRQWKH¿OWHUFRUUHVSRQGWRWKHSLQVRQ
the sides of the motor protection grill.
2. 7XUQWKHFDUERQ¿OWHUFORFNZLVHWREORFNWKHPED\RQHW¿[LQJ
NOTE:7KHFKDUFRDO¿OWHUVFDQQRWEHFOHDQHG,WVKRXOGEH
UHSODFHGHYHU\PRQWKVGHSHQGLQJRQKRRGXVDJH
Extension Liner Kit
 30” wide x 17” or 20” deep liner is available for both EAS428SS
and EPR628SS which provides complete protection of the
cabinets PRGHOQXPEHU(;;+'/
 36” wide x 17” or 20” deep liner is available for both EAS428SS
and EPR628SS which provides complete protection of the
 FDELQHWVPRGHOQXPEHU(;;+'/
See Liner installation instructions for more detail.

13
WARRANTY
ELICA North America TWO-YEAR LIMITED WARRANTY
TO OBTAIN SERVICE UNDER WARRANTY
2ZQHUPXVWSUHVHQWSURRIRIRULJLQDOSXUFKDVHGDWH3OHDVHNHHSDFRS\RI\RXUGDWHGSURRIRISXUFKDVHVDOHVVOLSLQRUGHUWR
obtain service under warranty.
PARTS AND SERVICE WARRANTY
)RUWKHSHULRGRIWZR\HDUIURPWKHGDWHRIWKHRULJLQDOSXUFKDVH(OLFDZLOOSURYLGHIUHHRIFKDUJHQRQFRQVXPDEOHSDUWVRU
FRPSRQHQWVWKDWIDLOHGGXHWRPDQXIDFWXULQJGHIHFWV'XULQJWKHVHWZR\HDUOLPLWHGZDUUDQW\(OLFDZLOODOVRSURYLGHIUHHRI
FKDUJHDOOODERUDQGLQKRPHVHUYLFHWRUHSODFHDQ\GHIHFWLYHSDUWV
WHAT IS NOT COVERED
 'DPDJHRUIDLOXUHWRWKHSURGXFWFDXVHGE\DFFLGHQWRUDFWRI*RGVXFKDVÀRRG¿UHRUHDUWKTXDNH
 'DPDJHRUIDLOXUHFDXVHGE\PRGL¿FDWLRQRIWKHSURGXFWRUXVHRIQRQJHQXLQHSDUWV
 Damage or failure to the product caused during delivery, handling or installation.
 Damage or failure to the product caused by operator abuse.
 Damage or failure to the product caused by dwelling fuse replacement or resetting of circuit breakers.
 Damage or failure caused by use of product in a commercial application.
 Service trips to dwelling to provide use or installation guidance.
 /LJKWEXOEVPHWDORUFDUERQ¿OWHUVDQGDQ\RWKHUFRQVXPDEOHSDUW
 1RUPDOZHDURI¿QLVK
 :HDUWR¿QLVKGXHWRRSHUDWRUDEXVHLPSURSHUPDLQWHQDQFHXVHRIFRUURVLYHRUDEUDVLYHFOHDQLQJSURGXFWVSDGVDQGRYHQ
cleaner products.
WHO IS COVERED
7KLVZDUUDQW\LVH[WHQGHGWRWKHRULJLQDOSXUFKDVHUIRUSURGXFWVSXUFKDVHGIRURUGLQDU\UHVLGHQWLDOXVHLQ1RUWK$PHULFD,QFOXGLQJ
WKH8QLWHG6WDWHV*XDP3XHUWR5LFR869LUJLQ,VODQGV&DQDGD
7KLVZDUUDQW\LVQRQWUDQVIHUDEOHDQGDSSOLHVRQO\WRWKHRULJLQDOSXUFKDVHUDQGGRHVQRWH[WHQGWRVXEVHTXHQWRZQHUVRIWKH
product. This warranty is made expressly in lieu of all other warranties, expressed or implied, including, but not limited to any
LPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\RU¿WQHVVIRUDSDUWLFXODUSXUSRVHDQGDOORWKHUREOLJDWLRQVRQWKHSDUWRI(OLFD1RUWK$PHULFD
provided, however, that if the disclaimer of implied warranties is ineffective under applicable law, the duration of any implied
ZDUUDQW\DULVLQJE\RSHUDWLRQRIODZVKDOOEHOLPLWHGWRWZR\HDUIURPWKHGDWHRIRULJLQDOSXUFKDVHDWUHWDLORUVXFKORQJHUSH
riod as may be required by applicable law.
7KLVZDUUDQW\GRHVQRWFRYHUDQ\VSHFLDOLQFLGHQWDODQGRUFRQVHTXHQWLDOGDPDJHVQRUORVVRISUR¿WVVXIIHUHGE\WKHRULJLQDO
SXUFKDVHULWVFXVWRPHUVDQGRUWKHXVHUVRIWKH3URGXFWV
WHO TO CONTACT
To obtain Service under Warranty or for any Service Related Question
Please Call:
 (OLFD1RUWK$PHULFD$XWKRUL]HG6HUYLFHDW      
Or by Writing To:
 Elica North America, Attention Customer Service,
6658 156th Avenue SE,
Bellevue, WA 98006 USA
[email protected]