Elinchrom ONE User manual

ONE

Table of contents
Introduction 4
ONE characteristics 6
Before you start 8
General user and safety information 8
Display panel - Dashboard Menu 14
Menu Features 15
Flash unit setup 18
Daylight modelling lamp 22
Charging USB C Wall Charger 22
Updating the Firmware & the IOT Bluetooth® Module 24
Replace a Flashtube 26
Troubleshooting 27
Technical Data 27
Disposal and recycling 33
Legal Information 33
Declaration of conformity USA & Canada 36
Credits / Frequency Band 37
ONE
User manual ONE ELINCHROM — 3

Introduction
Dear photographer,
Thank you for buying the Elinchrom ONE battery
compact ash unit. All Elinchrom products are
manufactured using the most advanced technology.
Carefully selected components are used to ensure the
highest quality and the equipment is submitted to
many tests both during and after manufacture. We
trust that it will give you many
years of reliable service.
Please read the instructions carefully before use, for
your safety and to obtain maximum benet from many
features.
Your Elinchrom-Team
4 — ELINCHROM ONE User manual

This manual may show images of products with
accessories, which are not part of sets or single units.
Elinchrom set and single unit congurations may change
without advice and may differ in other countries.
Please nd actual congurations at www.elinchrom.com
For further details, upgrades, news and the latest
information about the Elinchrom System, please regularly
visit the Elinchrom website. The latest user guides
and technical specications can be downloaded in the
“Support” area.
Technical data, features and functions of Elinchrom
products are subject to change without notice. The
listed values can differ due to tolerances in components,
testing environment or measuring instruments.
No guarantee for misprints.
Keep this user manual for later information and
reference.
User manual ONE ELINCHROM — 5

ONE characteristics
The ONE battery compact unit offers Manual and Action
modes and TTL and HSS functionality with the Elinchrom
Transmitter Pro.
• 131 Ws maximum output power in Manual and TTL
modes
• 5 f-stops power range, 7-131 ws
• LED, dimmable with variable colour temperature
2700-6500 K & presets
• Action mode for optimised ash duration
• HSS and TTL is supported with the Transmitter PRO
after a rmware update
• Coloured TFT touchscreen
• USB-C socket for recharging & rmware updates
• Built-in Li-Ion Battery. Capacity: 41.04Wh
• Bluetooth® built-in for Smartphone App (*IOS is
available)
• 4 Groups, 20 Frequency channels
• The dedicated Group colour is visible at the
illuminated Elinchrom side logos.
• Internal WLAN for IOT module update and future
options
• Removeable metal tilt head with umbrella support
• Protective glass dome with diffuser cap
6 — ELINCHROM ONE User manual

• Supports EL Standard accessories and OCF with the
included Elinchrom OCF Adapter
• Lightweight complete unit only 1.5kg / 3.3lbs
• Small Dimensions; 23x16,5x10,5 cm / 9x6.5x4.1 inch
Elinchrom TTL
The TTL (Through the Lens Metering) mode allows you to
access fully automatic exposure setups according to your
digital camera.
If you wish to work in the Manual mode or combine both
modes, the unit enables you to save the TTL exposure
parameters as a starting point when passing to the
manual mode. The unit supports Skyport radio remote
control, TTL and HSS at full power and the fastest ash
durations at low power levels. To operate the unit in the
TTL mode, please use the radio remote Elinchrom Pro
and activate the TTL function.
• 5 f-stop ash power range
• TTL +/- 3 f-stops adjustable in 1/3 steps.
• Compatible with Canon, Nikon, Fujilm, Sony,
Olympus / Panasonic and Pentax
Manual mode
• Compatible with all Skyport Transmitters
• Flash power in 1/10 f-stop steps
• Saves the TTL power as a starting point for the
Manual mode.
User manual ONE ELINCHROM — 7

FIRMWARE UPDATES
The functionality is constantly extended and improved,
always use the latest rmware for the Transmitter Pro
and the ONE ash unit.
Before you start
GENERAL USER SAFETY INFORMATION
• Flash units are powerful light sources. Please be
aware of the danger, or inconvenience, that they may
present to some persons and children.
• Keep ash units out of reach of unauthorised persons
whenever possible.
• Keep ash units away from children!
• According to safety regulations, we draw your
attention to the fact that electronic ash units are
not designed for extreme outdoor use, in damp or
dusty conditions and should not be used after being
exposed to sudden temperature changes causing
condensation.
• The unit protection class conforms to IP20.
• Do not use without permission in restricted areas
(such as hospitals, laboratories, etc.).
• Do not use near ammable / explosive material. Keep
minimum 1m or more distance to any object.
• Never ash into the eyes of a subject without
warning. Close use may affect eyesight.
8 — ELINCHROM ONE User manual

• The ambient temperature whilst the unit is in use:
-20°C (-4°F) up to max. 35°C (95°F).
Storage temperature: -10°C up to 60°C.
Charging temperature: 0°C to 45°C
• There is high voltage and there can be high currents,
so please apply all the usual safety precautions when
handling the unit.
• Do not use ash units without a mounted and
working ashtube due to high voltage at the exposed
terminals!
• Flash systems store electrical energy in capacitors by
applying high voltage.
• The battery unit may retain an internal charge for a
considerable time.
• Internal defective charge capacitors may explode
whilst the unit is in use, so never switch on a ash
unit, once it has been found to be faulty.
• For your safety, never open or disassemble your
ashes. Only an authorised service engineer should
open or attempt to repair this unit.
• Always switch off the ash unit before changing
accessories.
• The unit, the ashtube and accessories may become
very hot during and after use! To avoid injuries,
handle with an insulating cloth or wait until parts
have cooled down. Avoid direct sunlight, which
User manual ONE ELINCHROM — 9

might heat up the ash unit and affect the photocell
efciency. Protect the ash unit when used in humid
conditions but ensure ventilation for cooling!
• On no account should any object be inserted into the
ventilation holes.
• Use only original Elinchrom Accessories. Damaged
cables, glass domes and cases must be immediately
replaced by customer service.
WARNING: PHOTOSENSITIVITY / EPILEPSY / SEIZURES
A very small percentage of individuals may experience
epileptic seizures or blackouts when exposed to certain
light patterns or ashing lights. These conditions may
trigger previously undetected epileptic symptoms or
seizures in persons who have no history of prior seizures
or epilepsy. If you, or anyone in your family, has an
epileptic condition or has had seizures of any kind,
consult your physician before using the EL unit.
IMMEDIATELY DISCONTINUE use and consult your
physician before resuming use of your EL unit if you
or any person experiences any of the following health
problems or symptoms:
• Dizziness
• Eye or muscle twitches
• Disorientation
• Any involuntary movement
10 — ELINCHROM ONE User manual

• Altered vision
• Loss of awareness
• Seizures or convulsion
BATTERY SAFETY AND CHARGING NOTICE
IMPORTANT! FOR YOUR SAFETY do not use the Battery
unit for a purpose other than those specied!
• To recharge the internal battery, use ONLY the
original Elinchrom Li-Ion Battery Charger. If the
recharging operation fails to complete even when a
specied recharging time has elapsed, immediately
stop further recharging and disconnect the charger.
• If the internal battery gives off odors, generates heat,
or is deformed, or in any way appears abnormal
during use, recharging or storage, immediately
remove the Battery Charger and stop using it.
• Recharge the ONE after using. Store the unit only
with a recharged battery!
• If the ONE is not frequently used, recharge the unit
latest after three months to avoid damaging the
Li-Ion cells by deep discharging.
• Do not expose the unit to extreme heat, cold or
humidity to avoid damages.
User manual ONE ELINCHROM — 11

DO NOT USE A FAULTY, APPARENTLY DAMAGED OR
DEFORMED BATTERY UNIT!
ELECTRICAL, CHEMICAL AND MECHANICAL
HAZARDS
• Do not disassemble, open or modify the Battery unit.
• Do not transport or store the Battery unit together with metal objects such
as necklaces, hairpins, etc.
• Do not pierce the Battery unit with a nail or other sharp objects, strike it
with a hammer, or stand on it.
• Do not strike or throw the Battery unit.
• If the Battery unit leaks and electrolyte gets into the eyes, do not rub them.
Instead, rinse the eyes with clean running water and immediately seek
medical attention. Otherwise, eye injury may result.
• Store the Battery unit in a location where children cannot reach it.
• Do not put the Battery unit into a microwave oven or a pressurized
container.
OUTDOOR USE
CAUTION! PROTECT THE BATTERY PACK AGAINST
HUMIDITY!
This product is designed for dry use and should not come
into contact with water or dust. In humid conditions
cover or otherwise protect the battery unit. Do not
immerse the Battery unit in water / seawater and do not
allow it to get wet. The unit protection class conforms
to IP20.
12 — ELINCHROM ONE User manual

TEMPERATURE PRECAUTIONS
To prevent overheating the product should not be
covered whilst in charge mode or in general use! Do not
use, charge or leave the Battery unit near a heat source
(+60°C or higher) such as an open re, a heater or direct
sunlight. If the Battery unit has been exposed to very
cold conditions, sudden exposure to warm or humid air
may cause condensation and malfunction.
FLASH TUBES AND LED-MODELLING LIGHT SAFETY
NOTICE
• Flashtubes and the LED-Reector dishes may become very hot during
and after use!
• Never touch a ash tube or exchange it before the unit has cooled down
and is disconnected from the pack.
• Do not re ashes from short distances directed towards a person.
• Do not use near ammable / explosive material.
User manual ONE ELINCHROM — 13

DASHBOARD VIEWS
The colour of the Group corresponds to the group
number :
Blue for Group 1
Yellow for Group 2
Red for Group 3
and Green for Group 4.
The Elinchrom logo on the side of the unit illuminates
with the color of the selected group.
1. Group 1-4
2. LED Modelling lamp menu , slide down on the
touchscreen by touching the grey bar
3. Battery status
4. Favorite Function;
default setting is Mod. Lamp on/off
5. Power value
6. Flash duration
1 2 3
4
5
6
14 — ELINCHROM ONE User manual

1
8
35
6
7
2
4
Work Screen
Shows the most important
settings, once the unit
is congured. Displayed
automatically after 45 sec of
inactivity.
Control Panel
1. On / Off Button
Long press: on/off
Short press: switch display to
Lock on / Flash / Modelling Lamp
/ LED colour temperature
2. Screen brighness sensor
3. Scroll Button
Save button: press to validate your choice
CW: +0.1 f-stop / down
CCW: -0.1 f-stop / up
4. Photocell
5. Menu Button
6. Touchscreen
7. Tilt head, removeable
8. USB C
USB-C socket for charge
and rmware update.
User manual ONE ELINCHROM — 15

On / Off Button
• Press 2 sec. to switch the unit on/off
• Short press to toggle between the displays: ash
power, LED light, LED colour temperature,
• Return function: from Menu to power display
Scroll Button
• Press for Test ash
• Long press to display user friendly name
• Left turn to decrease values or scroll functions in the
Menu
• Right turn to increase values or scroll functions in the
Menu
• Short press to conrm settings in the Menu
Menu Button
Press to enter the Menu for individual settings or touch
shortly the screen with two ngers.
Menu Icons For Fast Access To access the menu
short tap on screen
with 2 ngers
17 28 39
410 511 6
16 — ELINCHROM ONE User manual

Use the scroll button to select the function or touch directly on
the function with one nger, changing values swipe left / right:
1. Action Icon: Action mode on/off
2. Settings Icon: 15-unit features for individual unit settings
3. Sound Icon: On/off
4. Photocell Icon: On/off
5. Airplane Icon: Flight mode; switch all internal wireles
devices on/off
6. Bluetooth® Icon: On/off (Works with the IOS Elinchrom
App)
7. Group Icon (G): 1-4, Groups with dedicated Group
colours.
8. LED Colour Icon: LED color temperature pre-sets,
6 options
9. Frequency Icon (F): 1-20
10. Display Icon: Black or white background
11. Info-Icon (I) - Unit information; Friendly name, FW
Version, Skyport ID, Lifetime, Power-on count, ash
count
Info
Friendly name Elinchrom ONE by default, can be changed with the
computer or smartphone App.
Firmware rev. *******
Skyport ID *******
Life time In hours (hhhh:mm)
Power-on count How many times the units has been turned on
Flash count Total ash number
User manual ONE ELINCHROM — 17

USB C
The USB C offers the following options:
• Re-charging the built-in Li-Ion Battery with the
EL-mains charger
• Re-charging and operating the unit with the
EL-Power Bank
• Firmware updates with the Elinchrom Updater
software
Flash Unit Settings
ONE Feature ONE Settings
Flash before ready (1) Yes / No
Flash Scale (2) EL-Scale / 10 Scale / Ws
Modlamp VFC (3) On/off
Modlamp Timer Off / 15 / 30 / 60 minutes
Modlamp Scale (4) F-stop / Percent
Favourite function (5) Modlamp / Flash mode /Audio
/ Photocell
Auto stand-by Off / 1-59 minutes
Auto-off Off / 1-60 minutes
EL logo mode (6) Low, High, Off, Low on ready,
High on ready
EL logo color (7) Group color / White
Ready tone 1 , 2, 3
Ready volume Off, Low, Medium, High
18 — ELINCHROM ONE User manual

Keyboard click On / Off
Skyport On / Off
Wireless settings for IOT update (8) SSID / Setup
1. Flash before ready: If ash before ready is
activated, a ash can be released before the
ash unit is 100% recharged, for fast shooting
sequences. Deactivated, the unit will only release
a ash when 100% recharged, for exact exposures
at any power level.
2. Flash Scale: use the power scale you prefer. The
Elinchrom scale compatible with all EL-ash units,
just the 5.8 -10 power scale, -or power in Ws.
3. Modlamp VFC: Visual Flash Control, the LED will
switch off shortly, after a ash was released as
additional ash conrmation.
4. Modlamp Scale: LED power in f-stop, same as the
EL ash scale or in percentage
5. Favourite function: In the display a favourite
function can be programmed for fast access. These
functions are available; Modlamp / Flash mode /
Audio / Photocell.
6. EL logo mode: The EL logos on both sides of the unit
can be dimmed or switched off. Additionally, they
can be used as ash control feature. The side logos
will switch off shortly after releasing a ash, visible
from ash power setting 2.5.
User manual ONE ELINCHROM — 19

7. EL logo colour: The side logos can show the
dedicated Group colour to identify which unit works
in which Group, or just set to white.
Blue for Group 1
Yellow for Group 2
Red for Group 3
and Green for Group 4.
8. Wireless settings: The Wireless connection is
needed to update the “ IOT module functionality”
of the ONE. To proceed with regular Firmware
updates, the UPDATER software is required,
available as a free download on the EL website.
Screen Lock
To activate the touch screen
lock, press the ON button whilst
powering on the unit for 9s. The
lock symbol indicates that the touch
screen is locked.
To unlock switch the unit off and
on again.
20 — ELINCHROM ONE User manual

Unit Lock
This feature prevents that the unit switches on during
transport and may discharge the Li-Ion battery. To
activate this function: switch the unit off and press
shortly and immediately “Menu”. To unlock the on/off
button, press on and immediatley “Menu”.
Reset To Default Settings
Switch the unit on and release the ON button. When
the EL Logo appears press immediately the “ON” and
“Menu” button for 4 seconds until the display shows
“Reload all default parameters”.
Sub-menu Screen
Select feature by scrolling.
Swipe left or right to change
value between the arrowsBack Save Exit
User manual ONE ELINCHROM — 21