Godox Quicker D II User manual

Professional Studio Flash
专业影室闪光灯
说 明 手 册
Instruction Manual
中英文双语
Chinese English Bilingual
705-QD2000-00 Made In China
地址/Add: 深圳市宝安区福海街道塘尾社区耀川工业区厂房2栋1层至4层、4栋1层至4层
1st to 4th Floor, Building 2/ 1st to 4th Floor, Building 4, Yaochuan Industrial Zone,
Tangwei Community, Fuhai Street, Bao’an District, Shenzhen 518103, China
电话/Tel: [phone](8062) 传真/Fax: [phone]
邮箱/E-mail: http://www.godox.com[email protected]
深圳市神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.

产品参数
型号
闪光能量
闪光指数(m ISO 100)
色温
电源电压
闪光功率调控
造型灯功率
回电时间
闪光触发控制方式
闪光持续时间
保险丝
尺寸
净重
400Ws
65
5600±200k
AC200-240V/50Hz / AC100-120V/60Hz
OFF,5.0~10.0(1/32~1/1)
150W
0.3~1.5秒
Quicker600DII Quicker800DII Quicker1200DII
1200Ws
110
Quicker400DII
同步线插孔，光控感应，试闪按钮，无线控制插座
1/2000~1/800s
5A 8A
灯体直径Φ14cm 含把手高26cm
含保护罩长41cm
约2.66kg 约2.79kg
600Ws
76
800Ws
90
10A
约3.79kg 约4.21kg
含保护罩长51.15cm
维护保养
闪光灯在工作时，如发现异常，应立即关掉电源，查明原因。
灯体应避免震动，平时注意表面除尘。
灯体稍有发热为正常现象，无特别需要时，勿连续引闪。
除灯管与造型灯消耗品允许用户用原厂配置的自行装卸更换外，闪光灯的其他维护
概由本厂指定可供原厂配件之维修部负责。
1年保修，由于灯管与造型灯为消耗品，不在1年保修范围。
擅自检修此闪光灯，经发现将取消闪光灯之一年保修期，维修需要收取相关费用。
如果本品出现故障或者被水淋湿，唯有在专业人员维修后方可继续使用。
在维修和清洁本品时请断开电源。
如有技术更改，恕不另行通知。
FOREWORD
Thanks for choosing Quicker DII series studio flash. It is a durable and high-
performance strobe with complete functions to help professional photographers
create desired lighting effects. This product is suited for wedding, advertisement,
portrait, and fashion photography. The perfect light source and a Must in studios
and photo workshops! The Quicker DII flash offers:
CONTENTS
13 • Slave Trigger Model
14 • Buzz Function
14 • Key Combination
14 • Alarm Display
14 • Memory Function
14 • Wireless Control Function
15 • Tube Replacement
16 Technical Data
16 Maintenance
Bulilt-in Godox 2.4G wireless X system
Precise output displayed on LCD panel, 50 steps from 1/32 to 1/1 (or 5.0-10.0) in 0.1
increments.
High-qualified modeling lamp, 150W output and 5% to 100% manual light adjustment
Outstanding output stability, a tolerance of ≤ 2% under the same output
Anti-preflash function, enabling synchronization with cameras having a one-preflash
firing system
Automatic power discharge when the flash output is adjusted from high to low
Adjusted parameters intelligently remembered after 3s and automatically recovered
after a restart
Wireless control of the flash power ratio, the on-and-off of modeling lamp and buzzer,
as well as flash triggering with Godox X1, XT16 or FT-16 flash trigger.
0 Foreword8
0 For Your Safety9
0 Caution9
Names of Parts10
10 • Body
11 • LCD Panel
11 • Accessories
11 • Separately Sold Accessories
12 Operations
12 • Flash Preparation
12 • Power Connection
12 • Modeling Lamp
13 • Power Output Control
13 • Test Button
13 • Sync Triggering
13 • GR/CH Button
- 07 - - 08 -

Body
NAMES OF PARTS
1. AC Power Socket
2. Sync Cord Jack
3. Power Switch
4. Test Button
5. MOD/OFF Modeling Lamp Button
6. S1/S2 Slave Model Button
7. Group/Channel Button
8. BUZZ Button
9. Wireless Control Port
10. LCD Display
11. Light Sensor
12. Modeling Lamp Indicator
13. Test Indicator
14. Select Dial + SET Button
15. Fuse
16. Mounting Bracket
17. Umbrella Input
18. Direction Adjusting Handle
- 09 - - 10 -
11
10
1
6
9
5
18
14
3
2
7
8
15
16
17
4
13
12
To prevent damage to the product or injury to you or to others, read the
following warnings in their entirety before using this product. Keep these
safety instructions where users can read them for ready reference.
Do not disassemble or modify. Should the product break down, send the
defective back to the authorized service center for inspection and maintenance.
Keep dry. Do not handle with wet hands, immerse in water, or expose to rain.
Keep out of reach of children.
Please put the device in a ventilation environment and keep the parts of lighting
and heat dissipation holes are unobstructed. Do not use in flammable
environment.
As this product adopts make and break device, please keep it easy to be used.
No touching the heating parts of this product.
Please turn off the power and wear insulated gloves before installing and
connecting accessories. When replacing the tube or modeling lamp, please
make sure that the tube is cool and wear insulated gloves to prevent burns.
Do not flash directly towards naked eyes (especially those of babies), otherwise
it may lead to visual impairment.
Disconnect from the power supply when it will not be used for an extended
period.
CAUTION
After 30 continuous flashes at full power, the flash should be cooled down for
about 3 minutes. Overheating will occur if it is used continuously without cooling
down.
Do not keep using the modeling lamp for a long time; otherwise flammable
accessories attaching to flash head, e.g. softbox will get burnt. A 10-minute time
is recommended in this case. After 10 minutes, cool it down for 1 minute.
When using a snoot, do not keep the modeling lamp on for a long time or fire too
frequently (not over six times for one minute). Overheating will result in damages
for strobe housing and/or studio light.
Avoid sudden impacts as this can damage the flash tube and/or modeling lamp.
Warning

Separately sold accessories
The product can be used in combination with the following accessories sold
separately, so as to achieve best photography effects: X1, XT16 or FT-16 remote
control, Power Inverter, Softbox, Photographic Umbrella, Light Stand, Barndoor,
Snoot, etc.
When there is flammable accessory on the flash unit, do not keep the
modeling lamp on for a long time. It is recommended to cool it down
for one minute after 10 minutes' working.
1. Built-in 2.4G Wireless Transmission
2. Built-in Wireless Channel
3. Built-in Wireless Channel Dial
4. Slave Model Indicator
5. Beep
6. Temperature Alarm Display
7. Built-in Wireless Group
8. Flash Output
9. Modeling Lamp is off
10. Modeling Lamp is in the PROP
mode
11. Modeling Lamp shows the power
in percentage
12. Modeling Lamp is off when
triggering the flash
LCD Panel
1. Power Cord
2. Standard Reflector
3. Lamp Cover
4. Glass Protection Cover
5. Modeling Lamp
6. Instruction Manual
Accessories
OPERATIONS
Flash Preparation
Power Connection
1. Take down the lamp cover.
Install the modeling lamp and put
on the glass protection cover and
the standard reflector.
(To uninstall the standard reflector,
press the release button on the
flash head and turn the standard
reflector counter-clockwise to take
it out, as illustrated in the picture.)
2. Attach the flash unit onto an
appropriate light stand. Adjust the
mounting bracket (16) for a good
angle and make sure it is tightened and fixed. Use the direction adjusting handle
(18) to adjust the flash to a desired direction. Umbrella input (17) is for different
photo umbrellas to put in.
Use the power cord to connect the flash to an AC power source and turn on the
power switch (3).
Short press the Modeling Lamp Button (5) to choose the modeling lamp’s mode
(OFF, PROP and percentage); and long press the Modeling Lamp Button (5) to
switch on or off the function that the modeling is off when triggering the flash.
Modeling lamp will be off automatically after lighting for 4 hours, avoiding
overheat due to long-time lighting when the user is not nearby.
OFF: Modeling lamp is off.
PROP: The modeling lamp's power changes with the flash's power. The bigger
power the flash has, the brighter the modeling lamp is.
Percentage: Adjust the modeling lamp's light brightness manually from 5% to
100%.
Modeling Lamp
- 11 - - 12 -
CH
S
%
OFF PROP
1
7
9
8
6
4
11
12
2
3
5
10
5
4
3
21

Power Output Control
select dial (14) decides different power output, satisfying light requirements in
different environment. The power is adjustable freely from 1/32 to 1/1 which will
be accordingly shown on the LCD display (10). "--" on the display indicates that
the flash triggering function is turned off. Press the Test button to discharge
power when the flash output is adjusted from high to low.
Test Button
To fire the flash without taking a picture, press the test button (4). It can also help
adjust the flash brightness when combined with the select dial (14). Press the
SET button and turn on the flash to view its version.
Sync Triggering
The sync cord jack (2) is a Φ6.35mm
plug. Insert a trigger plug here and
the flash will be fired synchronously
with the camera shutter.
GR/CH Button
Short press the GR/CH button can
adjust the built-in wireless group. When the group indicator on the LCD panel is
blinking, turn the select dial to change. And long press the GR/CH button can
adjust the built-in wireless channel. When the channel indicator on the LCD panel
is blinking, turn the select dial to change.
Slave Trigger Model
Three slave triggering models are available and can be set by pressing slave
model button (6).
◆No optical control: S1 or S2 is not displayed on the LCD panel, indicating the
slave triggering function is shut down.
◆One fire model: S1 is displayed on the LCD panel, indicating the flash will fire
synchronously when receiving one external flash. In this model, the flash can
function as an auxiliary lamp, offering various effects of light and shadow.
◆Anti-preflash model: S2 is displayed on the LCD panel, indicating the flash will
receive two external flashes within 2 seconds and will fire synchronously when
receiving the second flash. In this model, the flash can function as an auxiliary
lamp, applicable to TTL system. With this anti-preflash function, the flash can
synchronize with cameras having a one-preflash firing system.
Buzz Function
The sound button (8) is used for deciding whether there is sound reminder for
ready flash after recharging. When the buzz indicator is on the LCD panel, the
buzz function is working; when it is disappear, the buzz function is not working. A
“BI” sound will be heard when it’s fully charged.
Key Combination
Synchronously press the GR/CH button and the S1/S2 button can turn on/off the
built-in wireless transmission. If there are no wireless and channel indicators
displayed on the LCD panel, the built-in wireless transmission is off. On the
contrary, the built-in wireless transmission is on. Synchronously press the S1/S2
button and BUZZ button to recover factory settings.
Alarm Display
E0 The temperature sensor is not connected.
E1 When charging, the capacitance and voltage are not rising within 1 second.
E2 The fastest heating-up component is over the extra temperature.
E3 Discharged capacitance and voltage rating +10%＞
Alarm sounds, BIBI, ringing per 0.5 second. Press SET button to stop alarming.
Memory Function
The device is equipped with memory function for the panel setting. It will help
remember the panel setting 3 seconds after you set it. When starting up the flash
next time, the panel setting will be the same as that before powering it off.
Wireless Control Function
The flash unit has built-in 2.4G wireless transmission, which can be used
together with X1 and XT16 flash trigger.
◆The flash unit is built in with a Wireless Control Port (9) so that you can
wirelessly control the on-and-off of your flash, modeling lamp and buzzer, as well
as adjust the flash output level, etc.
◆To control the flash wirelessly, you need a Godox FT series remote control set
(on-camera and on-flash). Insert its receive end into the Wireless Control Port (9)
on the flash and insert the transmit end into the camera hot shoe. Settings made
on the hotshoe-mounted transmit and receive ends will be wirelessly
communicated to the flash. Then you can press the camera shutter-release
button to trigger the flash.
◆For full instructions on the use of FT series remote control, see its user manual.
- 13 - - 14 -

Tube Replacement
Shut down the power and remove the power cord before replacing the flash tube.
Wear insulated gloves to loosen the iron wire on the tube, keep a balanced hold
on the two feet of the flash tube and pull out the old tube gently. Take down the
feet casing from the old tube and put it on the new one. Hold two feet of the new
tube, and target directly towards the two copper outlets, then push them slightly
in. Twine the iron wire on the stainless steel sheet to fix the flash tube.
Quicker600DII
600Ws
76
Approx.2.79kg
Quicker800DII
800Ws
90
Approx.3.79kg
MAINTENANCE
Shut down the device immediately when it works abnormally and find out the
reason.
Avoid sudden impacts and the lamp should be dedusted regularly.
It is normal for the lamp to be warm when in use. Avoid continuous flashes if
unnecessary.
Maintenance of the flash must be performed by our authorized maintenance
department which can provide original accessories. The flash-tube and the
modeling lamp are user-replaceable. Replacement tubes and lamps can be
obtained from the manufacturer.
This product, except consumables e.g. flash tube and modeling lamp, is
supported with a one-year warranty.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by
professional.
Disconnect the power when cleaning the flash or when changing the flashtube /
modeling lamp.
Changes made to the specifications or designs may not be reflected in this
manual.
TECHNICAL DATA
Model
Max Power (Ws)
Guide Number(m ISO 100)
Color Temperature
Operating Voltage
Power Output Control
Modeling Lamp (W)
Recycle Time
Triggering Method
Flash Duration
Fuse
Dimension
Net Weight
Quicker400DII
400Ws
65
5600±200k
AC200-240V/50Hz or AC100-120V/60Hz
OFF,5.0~8.0(1/32~1/1)
150W
0.3~1.5s
Sync cord, Test button, Slave triggering, Wireless control port
1/2000~1/800s
5A 8A
Flash diameterΦ14cm, height of flash with handle 26cm
length of flash with lamp cover length of flash with lamp cover
41cm 51.15cm
Approx. 2.66kg
Quicker1200DII
1200Ws
110
10A
Approx.4.21kg
- 15 - - 16 -