Elite Industries EL-904 User manual

PLEASE DO NOT RETURN UNIT TO STORE
FOR PARTS & CUSTOMER SERVICE PLEASE CALL 1-800-ELITE-48
CUSTOMER SERVICE HOURS EASTERN TIME 8:45 AM - 4:45 PM M-F
F
4
Plastic Glass
Cushion
G
4
Self-Adhesive
Spacer Disk for
under Glass Top
T2
16
Flat Support
Shelf Pins
I
4
1/2" Screw for
Wire Management
D
1
Hex Key
Tool
E2
20
1-3/16" Bolts for
Top & Bottom
Metal Frames
Hardware for unit assembly
Assembly Instructions
60" HIGH, EXTRA-TALL AUDIO RACK TOWER
OVERALL DIMENSIONS: 60" H x 291/4" W x 241/2"D
EL-904: Wenge Melamine
(A rich, deep brown-black, wood-grain finish)
EL-954: Gray Melamine
291/4"
241/2"
60"
CHROME
CHROME
CHROME
PARTS
1. Glass Top
2. Adjustable Wooden Shelf (5 identical)
3. Top Metal Frame
4. Leg A (2 identical, Front Left, Rear Right)
5. Leg B (2 identical, Front Right, Rear Left)
6. Bottom Metal Frame
7. Wire Management Channel
1
3
2
2
2
2
2
6
4
5
7
5
4
IMPORTANT NOTES &
CAUTIONS/WARNINGS
• Carefully read and follow these instructions for
assembly.
• Please handle parts carefully, some parts may
be heavy and can have sharp edges, we
recommend possibly using cloth protective
gloves for extra protection.
• To protect the unit and your flooring surface we
recommend working on a padded or carpeted area,
you may also use the open box the unit came
in for this purpose.
• For proper construction/assembly integrity & for
equipment loading weight support and safety, all
connections need to be sufficiently tight, however,
do not over-tighten connections to the point of
stripping screw threadings. Parts are designed to fit
together tightly, however, avoid excessive force but
rather align & fit panels together methodically and
with patience.
• For some heavy or large units, it may be
recommended for 2 people to work together on
this assembly.
• Please read additional important safety
information at the end of this instruction manual.
• We urge you to keep this manual with your unit for
future reference.
Thank you for purchasing this Elite product. You will need the following tools:
Phillips Head Screw Driver & enclosed Hex Key Tool

1ATTACH LEGS TO BOTTOM METAL FRAME
5
5
4
4
6
NOTE THE POSITIONS OF THE FOLLOWING:
• Back of Bottom Metal Frame (6) has 2 holes where
Wire Management Channel (7) will be attached.
• Holes for Shelf Pins (T2) should be positioned as
shown in diagram. They should be positioned to
support the side edges of Wooden Shelves (2).
• Top of each Leg (4,5) has a hole for attaching the
Top Metal Frame (3) in Step 2 .
BACK
FRONT
SHELF PIN
HOLES
LEFT SIDE
RIGHT SIDE
SHELF PIN
HOLES
E2
E2
D
D
E2
D
D
E2
5
5
4
4
2ATTACH TOP
METAL FRAME
E2
D
Align holes at corners of
Top Metal Frame (3) with
corresponding holes
on all 4 Legs. Insert 4
Bolts (E2). Using Hex Key (D)
attach Top Metal Frame
to unit’s legs.
TIGHTEN BOLTS
COMPLETELY.
Bolt “E”
goes all
the way
through
Metal
Frame at
corners
3ATTACH WIRE MANAGEMENT CHANNEL
Using a Philips
head screwdriver
and Screws ( I ),
attach Wire
Management
Channel (7) to Top
Frame (3) and
Bottom Frame (6)
at back of unit.
NOTE: Wire
Management
Channel (7) has a
top bracket that is
shorter than the
bottom bracket.
I
I
3
3
6
6
Back of
Bottom Metal Frame
has 2 holes for
attaching Wire
Management
Channel (7)
Back of
Top Metal Frame has
2 holes for
attaching Wire
Management
Channel (7)
Attach each Leg to Bottom Metal Frame (6) using 4 Bolts (E2) and Hex Key Tool (D).
MAKE SURE TO TIGHTEN BOLTS COMPLETELY.

5ADD GLASS CUSHIONS
AND SPACER DISKS
4ADD SHELF PINS AND POSITION ADJUSTABLE SHELVES
2
T2
T2
Insert 4 Metal Shelf
Pins (T2) at desired
height for each
Adjustable Shelf (2).
NOTE: Bottom Shelf is not adjustable,
but rests in a fixed position on top of
Bottom Metal Frame (6).
Angle Adjustable
Shelf (2) and
carefully slide into
unit from the front
and rest it on
Shelf Pins (T2).
2
2
2
2
1
T2
T2
6ADD GLASS TOP
Place unit where
desired and care-
fully lay Glass Top
(1) on unit,
centering it on
Glass Cushions,
and resting on
Spacer Disks (G).
Make sure Glass
Top is centered
on Glass
Cushions with
equal overhang
at all four
corners.
Insert 4 Glass Cushions (F) into Top Metal Frame Holes
at corners as shown.
Attach 4 self-adhesive Spacer Disks (G) to top edges of
Top Metal Frame (3) as shown.
F
F
G
SIDE
BACK

Congratulations and enjoy your new ELITE product!
To clean your unit, apply window cleaner with soft tissue. This will also eliminate slight surface abrasions or
scratches that may have occurred in shipping or handling.
Distributed by: Elite Industries, 77 Gould Street • Bayonne, NJ 07002, Tel.: [phone] • Fax: [phone]
Elite Industries ensures complete satisfaction with this product. In the event of missing or damaged parts call toll free,
Customer service hours: 8:45-4:45, Monday-Friday, EST., 1-800-ELITE-48
IMPORTANT SAFETY PRECAUTIONS
Please carefully read & follow these important safety information notes for proper use of the furniture you have just assem-
bled. They are designed to avoid unsafe conditions that can result in property damage, bodily injury or death. We therefore
urge strict adherence to the following basic principals:
• Install this unit on a flat & level surface only.
• Avoid placing unit in direct sunlight or near heating source. We recommend not placing unit directly against wall but
rather leaving a narrow space between unit and wall for proper ventilation of your A/V equipment.
• Do not exceed the above recommended weight loading limits as this can result in sagging or structural failure of the sup-
porting panel leading to unsafe conditions.
• TV screen sizes are measured diagonally, therefore, base foot-print size for specific TV’s can not be determined by
screen size as they vary from manufacturer to manufacturer. Rather you will need to measure the TV’s base foot print and
compare it to the glass top panel surface size of your furniture as listed in this manual.
• Make sure to place TV within the surface area of the top panel, a bit inward from the front edge and centered. Never
use with a TV that is too large.
The TV base foot print surface must be able to sit completely on the top panel surface.
• When choosing locations for stacking A/V components on shelves, make sure to place the heaviest A/V equipment on
the lowest possible shelves/bottom panels first.
• Children should never be allowed to climb on or play with this furniture or/and the TV. This can result in an unsafe
situation which may lead to the TV and/or the furniture itself to become unsteady, slip, tip or fall over. Avoid using higher
shelves or the top surface of the TV for objects that may tempt children to reach and climb. Such items can include toys,
food, as well as remote controls, etc. Proper supervision and common sense is always required.
• Glass surfaces and doors are “Tempered.” This is a special process for achieving strength and safety. Although durable
& solid we recommend avoiding bumping into glass with force or dropping or chipping edges etc. Special caution should
be given to glass corners, both, for protection of glass as well as most importantly to avoid the possibility of injuries
resulting from strong impacts against corners especially with children. Doors should be opened & closed gently.
(Tempered glass is designed to shatter upon very strong impact and rather than producing sharp knife-like dangerous
edges, it turns instead into small pebble-like pieces.)
• Moving the unit: Do not drag unit when moving, especially not on a carpeted surface or on a rug. It is always recom-
mended instead to lift unit from both ends with a friend’s help. For the sake of safety and to avoid damages, we recom-
mend you remove the TV and all A/V components prior to moving this stand. It is a good idea to remove the glass panel
surfaces as well. If this is not possible please use much caution and good judgment and seek help to ensure stability and
safety as the stand is being moved. Make sure afterwards to properly re-adjust glass top and all equipment, centered
and stable as originally instructed above.
IMPORTANT NOTICE
The glass top panel surface, Part#1 is designed to be used for A/V equipment
NOT weighing more than 110 lbs. The loading weight needs to be evenly distributed across top panel
and for optimum stability choose a center position on glass top, not unbalanced to the side
against edge for example. It is primarily designed to house A/V components or for other
decorative items of choice. If, however, a TV set is being placed on the glass top panel for a
60" tall extra-high viewing angle, we strongly recommend exercising extreme caution
to ensure adequate stability and safety due to height. In any case DO NOT exceed the above weight-limit,
also, note dimensions for glass top panel surface as listed at the beginning of this manual
and read the following “Important Safety Precautions”.
Part #2, Adjustable Wooden Shelves, are designed to be used with A/V components
NOT weighing more than 66 lbs. per shelf.
The lowest wooden shelf level or bottom position:
This is not an adjustable level but the shelf rather sits firmly on the fixed bottom metal frame.
This level is designed to be used with A/V components NOT weighing more than 88 lbs.
However, for the total unit loading capacity, DO NOT exceed a total of 330 lbs.