Elite Products Elite E-Frame User manual

STOP!
Please read the following important information!
For questions on assembly or parts, DO NOT RETURN
product to the store. Contact the experts at Elite Products
by calling TOLL FREE.
1-800-338-8667
(Please keep this for future reference)
E-Frame
Assembly Instructions
Available Mon-Fri (8am-4pm) Pacific Standard Time
By Elite Products
Revision 2/25/2004

Parts List
E-frame Assembly Instructions Sheet
For questions on assembly or parts, DO NOT RETURN this product to the store.
Contact experts at Elite Products by calling TOLL FREE 1-800-338-8667
Please check parts list for correct hardware count. If the futon arms came in a separate box some hardware may
be packed inside. The quantities listed are the minimum required, you may receive extra hardware.
Curved Tube Support Leg x 1 pieces
Horizontal crossbar x 2 pieces
Square Tube Leg x 2 pices
Curved Tube Support Leg x 1pieces
A
B
C
D
ESupport Leg x 2pieces
F
5/16“ x 1 ½” Rounded Allen Bolts x2 pieces
5/16“ x ¾” Flat Allen Bolt x4 pieces
Transmission x2 piece
Insert Allen Nuts x4 piece
1
2
3
4
5
6
7
8
9
10
11
5/16“ x ½” Rounded Allen Bolt x2 pieces
5/16“ Lock Nuts x10 pieces
5/16“ Metal Washer x4 pieces
Allen Key x3 piece
5/16“ x 1 ½” Flat Allen Bolts x4 pieces
5/16“ x 2 ½” Flat Allen Bolts x4 pieces
SofaPostion
Sleeper Postion
½“Allen Wrench x1 piece
Eframe.cdr Style # 37-3504-050
G

Assemble
Step1
Step 2
Step #1
Attach Part A Mattress Frame (Seat, center and back section, Please note the back section
will be the largest sections) to Part B Square Tube Legs in front two channels on each side
using the 2 ½” Flat Allen bolts, metal washers and lock nuts. Use Allen key and Allen wrench to
tighten all bolts.
Step # 2
Attach the Transmission Hinges to the center mattress frame section using 1 ½” Rounded Allen
bolts and lock nuts. The rounded section of the Transmission Hinge must be facing the front with
the angle facing toward the back.
Style # 37-3504-050
E-Frame

Step 3 - 4
Step 5
Step # 5 Attach Part E Back Support Legs to the back section using ¾” male Flat Allen bolts
from the Underside of the frame and 5/16” female Insert bolts from the top of the frame.
To insure proper support and long lasting enjoyment of your futon
periodically retighten bolts. Also, it is recommend that you flip your
mattress periodically to ensure even wear.
Congratulations your futon is now assembled! To operate your new E-frame simply set the back
support legs into the rear channels on the Square tube legs Part #B for sofa position. In order to
make into bed position lift the back support legs from the rear channels (sometimes the back
support legs fit snug into the channels) and pull the back section away from the rest of the frame.
Make sure to swivel the center curved tube support legs Part C & D toward the rear of the frame
for maximum support.
Lay gripper on the top of the seat section to keep the mattress from slipping. The mattress works
best with slip cover if it is double folded on the seat.
Sofa Position
Sofa Position with Slipcover
Step #3
Attach Part C & D the two Curved Supporting Legs tubes together using the small ½” Rounded
Allen Bolts. Do not tighten completely until Step 4 is completed.
Step #4
Attach the Curved Support Legs to the transmission pieces using 1 ½” Rounded Allen Bolts from
the outside and locking nuts on the inside. Do not tighten too snug or firm this section must be
able to swivel. Now tighten Part C & D together. Refer to Step 4
Style # 37-3504-050
Eframe.cdr