Elite Projector MosicGO Sport MGFU-S User manual

www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
Projector
User’s
MosicGO®
Guide
MOVIES MUSIC POWER GO
SINCE 2017
0RGHO 6SRUW0*)86
/LWH0*)8/
M
MosicGO®


1. The ventilation ports prevent overheating. Never block these ports located on the sides and bottom of the projector.
(See page 12) Direct obstruction, confined spaces or placing on a cluttered surface restricts airflow, and ruins the projector.
2. To reduce risk of fire or electric shock, do not expose the projector to any liquids, rain, snow or airborne moisture.
3. Do not insta
4. Do not use the projector in direct sunlight.
5.
6. Do not use the projector in areas susceptible to excessive dust and dirt.
7. Turn off the product before cleaning.
8. Disconnect the power cord if the product is not being used for a long period of time.
9. Ensure that the ambient room temperature is within 0- 40°C (32-104°F).
10. Ensure that relative humidity is 5 - 35°C (41- 95°F), 80% (Max.), non-condensing.
11. Do not drop, throw or try to bend your product.
explosion.
13. Clean only with dry cloth.
14. Only use attachments/accessori
15. Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be (but not limited to):
DUnit has been dropped.
DCharger or plug has been damaged.
DLiquid has been spilled on the projector.
DProjector has been exposed to rain or moisture.
DSomething has fallen into the projector or something is loose inside.
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please contact your
local reseller or service center before you send the unit for repair.
17. Follow all warnings and cautions in this manual and on the projector.
18. The unit should only be repaired by appropriate service personnel.
19. Projector lamps generate a lot of heat. This causes much of the projector's surface area to heat up. If the projector seems to be excessively hot,
turn it off so that it can cool down and then call customer service.
(<(6$)(7<:$51,1*6
,03257$176$)(7<,16758&7,216
To avoid retinal damage, do not stare directly or indirectly into the projector's light beam.
Rather than stand in the projector's light beam to point on the screen, use a laser pointer or pointer stick instead.
Make sure that students and other viewers observe the eye safety warnings and stay out of the direct light beam.
Use window blinds and turn down interior light sources to reduce the washout glare of ambient light.
&23<5,*+7 75$'(0$5.
© Copyright 201.All rights reserved.
The manufacturer reserves the right to make technical changes. The manufacturer assumes no liability for damages incurred directly or indirectly from errors,
omissions, or discrepancies between the device and this documentation.
Other brands or logos are trademarks or registered trademarks of their respective companies.
&$87,21ħ5,6.2)%$77(5<(;3/26,21,),1&255(&77<3(,686('
0$.(685(723523(5/<',6&$5'86('%$77(5,(6$&&25',1*72
/2&$/5(*8/$7,216
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03


'(&/$5$7,212)&21)250,7<
75$'(0$5.6
)&&:$51,1*
$*(1&<$33529$/6
Apple, Macintosh, iPod, iPod nano, and iPhone are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark
2014/30/EU
EN 301489-1
EN 301489-17
EN 55032
EN 55024
Low Voltage Directive : 2014/35/EU
Safety: EN 62368 , EN62133+Annex.M
Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe andAcrobat are trademarks or registered
trademarks ofAdobe Systems Incorporated.
household waste in all EU member states. Please follow the guidance of your local environmental authority or ask the shop where you purchased
the product for collection or recycling options.
(2) this device must accept any interference received, including interference that may cause undesired operation.
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Changes or modifications not expressly approved may void authority to operate the equipment.
FCC, CE, and LVD
Other specific CountryApprovals may apply. Please see product certification label.
Product offerings and specifications may be altered at any time without notice.
6.3
)&&&$87,21
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
)&&5)H[SRVXUHZDUQLQJ
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03

352'8&729(59,(:
Kensington Lock Slot
Ventilation Port
USB POWER OUT
USB
12V Trigger Out
DC IN 19V
Power On/O Switch
USB Type C Display Port
(DP)
HDMI 2
HDMI 1
Earphone Jack
Touch
Focus
Ventilation Port
Tripod Mount Hole
Wireless Speaker
Projector
Wireless Speaker On/O Button
20. ProjectorOn/O Button
Battery / Power Status
3
1
25
7
8
13
12
9
10
11
16 17 18
6
4
14 15
19 20
*Note:
Follow the steps to open I/O cover.
(Battery indicator only for
MGFU-S model)

for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03

1 2
DP
Remote Control
Menu
1. Wireless Speaker On/Off, Audio Source Selection(Note)
2. ProjectorOn/O Brightness Adjustment (Note)
3.
Up (adjust keystone up)
4.
Left
5.
OK/Enter
6.
Right
7.
Down (adjust keystone down)
8.
Home
HDMI1
9. HDMI2
10.DP
Menu
11.Mute
12.Volume down
13.Volume up
14.
15.Video Source Search
16.
1. Up (adjust keystone up)
4. Left
3.
2. Down (adjust keystone down)
OK/Enter5.
Input Source Selection
6.
Home
7.
Right
Mute
8.
9.
Touch Keypad
352'8&729(59,(:
6
1
4
1
3
6
8
11
12
14
7
4
2
5
7
2
5
10
9
13
15
16
3
8
9

*Note:
When projector is off, short press PJ button on remote control to turn on projector.
When projector is ON, short pressing the PJ button on the remote control will cycle through
the following brightness modes: MAX, ECO, and MIN.
When projector is on, long press PJ button on remote control over 1 second , after prompt message
and then short press PJ button again to turn off projector.
When Wireless Speaker is off, short press BT button on remote control to turn on Wireless Speaker.
When Wireless Speaker is on, long press BT button on remote control over 1 second to turns off Wireless Speaker.
When both of projector and wireless speaker are ON, short pressing the BT button will cycle through the source of
speaker between projector and wireless audio source.
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03


Connect the power cord to the
DC input jack.
Insert the plug into power
outlet.
1-A AC Adapt r
1-B Power Cord







3.
HDMI Cable x1
4.
USB Type C Cable
(*Note: only apply for
Sport MGFU-S model)
(*Note: Only Sport MGFU-S model has a battery pack)
4-A Remote Control
4-B Battery (AAAx2)
5.
6. Tripod 7. Carrying bag
User’s Guide (with Warranty Card)
352'8&7$&&(6625,(6/,67
32:(5212))
1-A 1-B
4-B
MGFU-S only
4-A
or
4.Press the Power On/Off Switch. The OK icon on the touch keypad will illuminate.
MosicGO®has an internal battery pack.
Please fully charge the battery before using the projector.
3 .
Projector
User’s
TM
MosicGO
Guide
MOVIESMUSIC POWER GO
SINCE2017
PrintedinTaiwan
www.eliteprojector.com
FBZZ-MG1Z002-01
0RGHO6SRUW0*)86
/LWH0*)8/
Electronicfilelink
www.eliteprojector.com/MGFU/manual
TM
MosicGO
M
MOVIES MUSIC POWER GO
TM
MosicGO
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03

%763($.(5352-(&725212))

%763($.(5352-(&725212))%763($.(5352-(&725212))
*Note:
Press the Wireless Speaker button / PJ button to turn off Wireless Speaker / projector before press power off switch.
Avoid press power off switch directly when projector / Wireless Speaker still on
18
19
7
7
*Note:
An audible tone sounds when the Wireless Speaker powers on/off,
or when the projector connects/disconnects to a device.
PresstheWirelessSpeakerbuttontoactivatethis
feature.It’s blue LED lamp will flash when the
Wireless Speaker is in pairing mode. Check
“MosicGO®” on your device to connect to
MosicGO®Wireless Speaker . When device is
connected successfully, the blue LED lamp will
lightpersistently.ToturnofftheWirelessSpeaker,
press down and hold the BT button for over 1
second.When both projector and Wireless
Speaker are ON, short pressing the Wireless
Speaker button on the remote control will switch
audio source between projector and Wireless
Speaker.
Press the PJ button to turn the projector on and
the status LED indicator will light up. To turn off
the projector, press and hold the PJ button for
over 1 second. After seeing prompt message,
short press PJ button again to confirm. The
MosicGO®logo will show briefly before the device
powers off.The status LED indicator light will be
flashing as the projector powers down.When
projector is ON, short pressing the PJ button on
the remote control will cycle through the following
brightnessmodes: MAX, ECO,andMIN.
1.
2.
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03

%$77(5<67$786,1',&$725
%$77(5<)2532:(56285&(

USB Type C power Delivery:
Type C support PD function. Please refer specification section for details.
USB Type A :
Provide 5V/1A max power.
LEDs indicate battery and chargingstatusas following table.
Inbattery mode, MosicGO®will be forced topoweroff if battery
capacityis under 10% Suggest chargingthebattery immediately if
LEDindicator is Red.
*Note:
There is no battery in Lite MGFU-L verion. Power LED is green solid when
DC adapter is inserted.)
*Note:
When projecting video content, USB type C ports automatically switch to a
lower (5V1A) power rail.
Adapter Mode Battery Mode
Geen(100%) Solid Solid
Green (80% ~) Flash Solid
Orange(15%~79%) Flash Solid
Red(~14%) Flash Solid
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03

The projector is equipped with four elevator feet for adjusting the
projected image tilt.
To adjust the tilt:
Turn the elevator feet to adjust the projected image position to the
desired tilt.
$'-867352-(&7,21,0$*(7,/7
Adjust the focus until the image is clear.

&211(&7,13876285&( +'0,RU86%7\SH&'LVSOD\3RUW
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03
1. Connect the device using HDMI or USB type C cable.
or


$'-8677+(352-(&7,21,0$*(6,=(
$
$%
'
'
(
(
&
&
WDEOH
VFUHHQ
*Note:
The tolerance is around 5% .
$%&'(
3URMHFWRU)URQW
(GJH'LVWDQFHWR
6FUHHQ
6FUHHQORZHU
HGJH
WRSURMHFWRUWDEOH
3URMHFWRU6FUHHQ
GLDJRQDO
3URMHFWRU6FUHHQ
ZLGWK
3URMHFWRU6FUHHQ
1RWH
*Note
*Note
KHLJKW
FP FP FP FP FP
    
    
    
   

   

$%&'(
3URMHFWRU)URQW
(GJH'LVWDQFHWR
6FUHHQ
6FUHHQORZHU
HGJH
WRSURMHFWRUWDEOH
3URMHFWRU6FUHHQ
GLDJRQDO
3URMHFWRU6FUHHQ
ZLGWK
3URMHFWRU6FUHHQ
KHLJKW
LQFK LQFK LQFK LQFK LQFK
    
    
    
    
    
1RWH
*Note:
The MosicGO®(Lite MGFU-L & Sport MGFU-S) portable UST (ultra-short throw) projectors are specifically
designed for creating 60-80” imagery in a 16:9 aspect ratio.
Throwing larger (90”-100”) images will have corner distortion and is more recommended for videos than in still
shot / training presentations.
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03


To Earphone Plug
To 12V Trigger Plug
975,**(5
GND HPR HPL
Earphone, 3.5mm Jack Pin assignment
HPL : Left Channel Audio Signal
HPR : Right Channel Audio Signal
GND : Signal Ground
GND 12V
Warning : Don’t plug in earphone to 12V trigger port,
that can cause damage to the earphone.
12V Trigger Port, 3.5mm Jack Pin assignment
12V : 12V trigger signal for screen rolling up/down
GND : Signal Ground
($53+21(
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03


&2
Screw a standard tripod into the screw hole on the projector.
*
Note
:
T
ripod should support loadin
g
above 3K
g
, and mountin
g
screw spec is 1
/
4”
1. Loosen 4 screws metal plate from MosicGO®.
2. Fasten screws to ceiling mount kits.
Screw hole for tripod *Standard Tripod
Mount on ceilingMount on tripod
M4 Screw
( x 4 )
  028177+(352-(&725
M4
( x 4
Note2
Keep enough space from speakers and ventilations (30 cm above)
On table
4 rubber feet are placed on flat surface.
Prevent to block bottom’s ventilations.
Note1
WDEOH
WDEOH
*Note:
Please keep air vents opend for heat ventilation. Otherwise, projector will be turned off if it's over heat.
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03


26'
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03
PICTURE
Contrast
MENU
Sharpness
Pattern Test
RGB
OK
Contrast:adjust color contrast.
Sharpness:adjust picture sharpness.
PatternTest: present patternpictureto verifyfocus
andcolor situation ofdisplay.Press “OK”willreturn
tocurrent video port.
PictureTest: circularly presentred,green, blue,and
whitescreen to verifypicturecolor. Press“OK”will
returnto current videoport.
*Note:
1.Contrast and Sharpness can be configured only when video signal is ready.
2.Reset to default setting by selecting 'Menu'->'Other'->'Reset
DISPLAY
Auto PowerOff Off
MENU
H Position
V Position
RGB
［ ［
OK
AutoPowerOff: Configure thetimebefore poweroffif there
isno signal toprojector.
H/ V Position:Adjustthe displayposition
*Note:
1.H Position and V Position can be configured only when video signal is ready.
2.Reset to default setting by selecting 'Menu'->'Other'->'Reset'
Picture Test
MosicGO®
MosicGO®


26'
COLOR
Gamma Off
Off
Standard
RGB
MENU
Color Temp
Color Effect
Color Format
HUE
Saturation
RGB
［
［
［
［
［
［
［
［
OK
Configurecolor properties.
*Note:
1.All COLOR Menu can be configured only when video signal is ready.
2.Some features might not be supported in current model.
3.Reset to default setting by selecting 'Menu'->'Other'->'Reset'
ADVANCE
Aspect Ratio Full
FrontTable
Off
MENU
Orientation
Ultra Vivid
RGB
［
［
［
［
［
［
OK
Setother configuration.
AspectRatio: configure ratioofdisplay area.
Orientation:according to yourprojectorinstallation,
configurethe orientation ofdisplay.
Ultravivid: enable/disable supportingvividcolor.
*Note:
1.Aspect Ratio and Ultra Vivid can be configured only when video signal is ready
2.Some features might not be supported in current model.
3.Reset to default setting by selecting 'Menu'->'Other'->'Reset'
MosicGO®
MosicGO®
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03


26'
OTHER
12V Trigger Off
Off
On
MENU
Keystone
Transparency
S.P.M(SPORT)
RGB
［
［
［
［
［
［
Reset No
［ ［
OK
12VTrigger: Enable/disable theoutputof 12VTriggerOut.
Keystone:adjust the rectangleshapeof display.
Transparency:configure the transparencyof
OSD(on-screendisplay).
S.P.M:enable/disable Smart ProjectorMode.If
enable,MosicGO®willautomatically adjust
brightnessaccording current batteryand
powersituation.
Buzzer:enable/disable “beep” alertsound.
Rest:reset to defaultsetting.
INFORMATION
MENU
RGB
OK
Presentcurrent video signalinformation.
Buzzer On
［ ［
20190729 V59
Press menu key to turn on/off menu
HDMI
1080p
H: 67.5K Hz V: 60.0Hz
PCLK: 148.4MHz
HDCP Disabled
*Note:
1.Brightness cyclic MAX/ECO/MIN will be disabled when S.P.M is ON.
2.If Keystone is enabled , the projector will automatically adjust the image
display within 2-3 seconds. Press up/down key to adjust slightly also.
3.Reset to default setting by selecting 'Menu'->'Other'->'Reset'
MosicGO®
MosicGO®
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03


If you experience a problem with your projector, please refer to the following
information. If a problem persists, please contact your local retailer or service
center.
No image appears on screen
Image is out of focus
Make sure the projection distance is in valid range (refer to page 10).
Ensure the cable is fine.
Image is too small or too large
No sound
Supported HDMI input video signal:
s   on the remote control .
* If an invalid signal is input into the projector, it will not be displayed properly on the screen or a
message such as 'not support' will be displayed.
* To provide the best picture quality, 1920 x 1080 (1080p) resolution is recommended.
Item Description
Imager DLP
Native
Resolution 1x 1080
Projection
Distance 0. -0. m (1' " - 2'2") (from screen to lens)
Projection
Focus Manual
Throw Ratio 0. (80"@0.5m)
Keystone Vertical keystone
Projection Modes Front Table, Rear Table, Front Ceiling, Rear
Ceiling
Standard Input
Up to (1920 x 1080)
SDTV/EDTV/
HDTV 480i, 480p, 576i, 576p, 720p, 1080p
Horizontal
Frequency 30.5 - 91.1kHz
Vertical
Frequency 50 - 85Hz
Operating
Temperature 0 - 40°C
Dimensions
(WxHxD) (back) / 127(front)mm
AC adapter
Power Input 100 - 240V, 50 - 60Hz
19V DC, 6.3A
Power
Consumption
Lamp RGB LED
Lamp Life 20,000 Hours
Speakers 8W x 2 music power
Battery Capacity 37200mAH (135 Watt-Hours)
(only for MGFU-S model)
Input/Output
Ports
Alt-DP (USB type C connector) x 1
HDMI 1.4 x 2 Resolution
640 x 350
720 x 400
640 x 480
800 x 600
1024 x 768
1152 x 864
1360 x 768
1280 x 1024
1920 x 1080
Horizontal Frequency (kHz) Vertical Frequency (Hz)
31.468
31.469
31.469
37.879
48.363
54.348
47.712
63.981
67.5
70.09
70.08
59.94
60.31
60.00
60.053
60.015
60.020
60
Earphone out
USB type A poewr charging port (5V1A) x 2
12V Trigger Out (0.1A output max.)
Wireless Speaker audio in x 1
Security Kensington Slot
Waterproof IPX2
1.52-2.54 m ( " - 100")
Less than 120W
USB type C PD power source port x 2 (Note)
63(&,),&$7,216 7528%/(6+227,1*
Lens with dust or water drops
• Projecting test pattern (“Menu” -> “Picture” ,press ”OK”-> “Pattern Test”
,press ”OK”)
• Adjust the focus ring, make the line pattern on four corners and center
clear.Exit “Pattern”by press “OK”again.
• Use a hairdryer on a low heat setting to clear away dust, water or other
particles. To Prevent Damaging the Surface Coating, DO-NOT Touch,
Wipe or Clean the Lens.If the projection surface is heavily soiled, contact
the manufacturer for further assistance.
Size
*Note:
Power Delivery (PD): maximum 5V/3A,9V/3A,15V/3A,20V/4.35A for port USB type-C port
maximum 5V/3A,9V/3A,15V/2A,20V/1.5A for port USB type-C port
3
8
*Note:
MGFU-S/MGFU-L is splash resistant and was tested under controlled laboratory
conditions with a rating of IPX2 under IEC standard 60529. Splash resistance are
not permanent conditions and resistance might decrease as a result of normal wear.
Do not attempt to charge a wet MGFU-S/MGFU-L; Liquid damage not covered
under warranty. “To Prevent Damaging the Surface Coating, DO-NOT Touch, Wipe
or Clean the Lens.*Consult the manufacturer for special cleaning instructions.”
*Note:
When the projector’s temperature is too high, the projector automatically shuts down
due to the built-in temperature protection. This is not a malfunction. Let the projector
cool down before switching it on again.
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03


7528%/(6+227,1*
3 continuous beep sound
You may hear 3 continuous beep sound accompany following icon on the screen
Fan error: projector is turned off immediately. If the problem still
occurs, please check your vendor.
Over heat: projector is turned off immediately. Suggest to let
projector be off for a while before it is turned on again.
Low battery: projector is turned off immediately. Please plug
power adapter to charge the battery. You can turn on the
projector during charging.
Battery fail: if the power adapter is plugged. You can turn on and
use projector. If you pull out the power adapter, the projector may
be turned off without any warning. If the problem still occurs,
please check your vendor.
*Note:
Projector may be over heat and turned off immediately. Suggest to let
projector be off for a while before it is turned on again.
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03


48,&.6(783)2502'(/206+
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03
aąFP aąFP
aąFP


0RQWKV:DUUDQW\&DUG
(OLWH6FUHHQV9LVXDO6RXQG&R/WG
＊Toensureyourright, pleaseaskthe Dealertofill intheinformation
above,andhaveDealer’s stamponthis card.
＊Ifdateofpurchase cannotbeprovided withdealer’sstamp, themanufacture
dateasrecordedwill bedeemedto bethestart oftheWarranty Period.
Customer’s name:
Phone number:
Email:
Date of purchase: (M) (D) (Y)
Address:
Model No:
S/N:
Dealer’s Stamp:
MOVIES MUSIC POWER GO
MosicGO®
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03

www.eliteprojector.com
Printed in Taiwan
FBZZ-MG1Z002-03
MOVIES MUSIC POWER GO
for more update user manual:
Electronic file link
www.eliteprojector.com/MGFU/manual
MosicGO®