Elite Progres Plus Series User manual

F
13. Secure Keypad ‘F’ cable in place using Cable Clip ‘N’ and
Cable Clip Screw ‘P’ in the middle right of the Desktop ‘A’.
N&P
A
...Helpline 01405 746 000
www.elite-furniture.co.uk
Please Read This Leaflet
Before Assembly
Range Progress Plus
Desk Style Sit / Stand Single Workstation
Assembly Instructions
2 Person Assembly
Rev. v2 06/2019
Tools Required
5mm Allen Key
or Hex’ Screwdriver
Pozi Screwdriver
Components
A
A
G
Desktop Panel x 1
B
B
Sub-Frame x 1
C
C
E
Leg Column x 2
DLeg Base x 2
E
D
Cable Tray x 1
FA: Standard Keypad
B:
FB: Advanced Keypad
GKeypad Screws (20mm Reisser) x 2
x 1
HAllen Screws (M6x32) x 8
JLeg Base Bolts (M6x20) x 8
KCable Tray Screws (13mm Self Tapper) x 2/3
NCable Clip x 1
PCable Clip Screw (16mm Reisser) x 1
LDesktop Bolts (6x12 Pan Head) x 4
MSub-Frame Rail Bolts (50mm Confirmat) x 2
QCable Ports x 2
13
14. If Cable Ports ‘Q’ are not already attached, insert both
Cable Ports ‘Q’ into Desktop ‘A’ apertures.
The Progress Plus Single Desk is now fully assembled.
Q
A
Q
14
F
A:
F
H MJ L
N P Q
K
Rev v2 06/2019
N P
P

5. With assistance, turn the assembled frame upright and lay
gently on a at surface.
6. Connect the yellow cable ends from Leg Columns ‘C’ to the
power packs ‘Z’.
If the cables are too short, an extension will be supplied.
B
C
7. Insert Keypad ‘F’ Cable through the aperture in Sub-Frame
‘B’ and connect to the power pack.
At this point, plug in the mains power adapter to operate the
height adjustability.
BF
12. Fix Keypad ‘F’ to the right side of Desktop ‘A’ using 2x
Keypad Screws ‘G’ with the controls facing the front edge.
For Standard Keypad ‘FA’, use the inner holes ‘Y’.
For Advanced Keypad ‘FB’, use the outer holes ‘X’.
F
4. Repeat steps 1-4 on the opposite side of Sub-Frame ‘B’.
11. Once xed, insert screws ‘M’ into the Outer Rail of
Sub-Frame ‘B’ securing Desktop ‘A’.
A
1 2
1. Lay Sub-Frame ‘B’ upside-down on a at surface.
Take Leg Column ‘C’ and place it in-between the 2 middle rails.
2. Using 4x Allen Screws ‘H’, x Sub-Frame ‘B’ to
Leg Column ‘C’.
3 4
3. Carefully position Leg Base ‘D’ on top of Leg Column ‘C’
with the adjustable feet facing upwards. Using 4x Leg Base
Bolts ‘J’, x Leg Base ‘D’ to Leg Column ‘C’.
5 6
7 8
8. Insert Cable Tray Screws ‘K’ halfway into the rear rail of
Sub-Frame ‘B’ leaving 5mm protruding.
910
9. Align the holes of Cable Tray ‘E’ to Screws ‘K’.
Using a hooking action, place Cable Tray ‘E’ onto Screws ‘K’,
before tightening Screws ‘K’ fully.
10. With assistance, lift and place Desktop ‘A’ onto the frame
so its cable port holes are along the rear edge.
Fix each corner of the Desktop ‘A’ to the frame, using 4x
Desktop Bolts ‘L’.
11 12
A
L
L
E
D
C
B
C
C
D
D
B
Rear Edge
H
K
JL
G
M
H
B
C
K
M
J
G
X
Z
X
Y
K
B
C