Elmwood U-7200C User manual

Royal Elm Designer Table U-7200C
Assembly Instructions
Contents of Carton: Contents of Parts Bag:
[1] Threaded Lever [AA] [1] Large Washer for Lever
[BB]
[1] Female Knob
[CC]
[2] Male Knob [DD] [1] Washer for
Female Knob
[EE]
[2] Female Knobs
with bolt & washer
included [FF]
[2] Large Pin with
hole [EE]
[2] “C” Washers for
Large Pins
[FF]
[12] Long Wood
Screws [GG]
[2] 1-3/4” Bolts
[HH]
[4] Small Wood
Screws [II]
[2] Metal Tilt Adjustment Rods [JJ]
[2] Metal Pin End Caps for Tilt Rods [KK]
[2] Left & Right Legs
for A-Base [B]
[2] A-Base Ends [A]
[2] A-Base Cross Supports [C]
[2] Chanelled Side Supports [D]
[1] Upper Cross ESupport [E]
[2] Drawing Top Braces [G]
[1] Chanelled Cross Member with Threaded Rod [F]
Created July 06 - RPI

STEP 1] Assembling A-Base(s)
Assembly Instructions:
A-Base end [A] Left Leg [B]
Position the Left Leg [B] onto the A-Base, lining up holes.
Secure with [2] Long Wood Screws. Tighten. See below for
proper assembly.
Long Wood
Screws [GG]
Repeat with other side.
Now, you should have [2] complete A-Base Assemblies.
STEP 2] Attaching A-Base Supports
Proper assembly of
A-Base & support.
STEP 3] Attaching Channelled Side
Repeat with other support.
Attach as shown to right.
B
A
D
C
C
C
C
C
STEP 4] Adding Lower Support & Rod
A-Base Cross Supports [C]
A-Base Assembly
After securing with washer [EE] and Female Knob [CC],
turn assembly up onto base as shown below.
C
F
F
C
D
D
Washer [EE]
and Female
Knob [CC]
Created July 06 - RPI
Take one assembled A-Base end and attach [1] support
bar (with Logo reading up in correct position) and place into
notch and secure with [1] long wood screw [GG]. See below
for proper assembly.
With above assembly still laying flat on surface, insert one
end of Channeled Cross Member with Threaded Rod [F]
into Channelled Side Support [D] making sure rod end goes
through other end of A-base assembly. Secure with Washer
[EE] and Female Knob [CC]
Take A-Base end that has the two supports attached and
place on flat surface. Position Channelled Side Support [D]
into middle section of A-Base. Making sure channel is on
bottom end. As shown below.
Take the A-Base end [A] as shown below and the Left Leg
[B] for the A-Base.
Pg. 2

STEP 5] Securing Lower Support & Rod
Assembly Instructions continued:
C
F
D
Close-up photo of
Lever and large
Washer.
STEP 6] Attaching Upper Cross Support
D
FC
E
E
D
D
F
C
After Steps 1 - 6.
Base should look like
photo to right.
STEP 7] Inserting Pin into Side Support
Close-up photo of
1-3/4” Bolt attachment.
STEP 8] Attaching Tilt Adjustment Rods
KK
JJ
STEP 9] Securing Tilt Adjustment Rods
EE
DD
Created July 06 - RPI
Pg. 3
Take Upper Cross Support [E] and insert one end into small
slot in upper portion of the Channelled Side Support [D].
Secure with 1-3/4” Bolt [HH]. Tighten with Phillips
Screwdriver. Insert other end into other side of Channelled
Side Support [D]. Secure with other 1-3/4” Bolt [HH]. PLEASE
NOTE: You may have to loosen Lever to allow Side Support
to pull away enough to allow end of Upper Cross Support
[E] to be inserted into slot. Retighten Lever once completing
Step 6.
Take [1] of the Metal Tilt Adjustment Rods [JJ] and insert it
into the hole in the Pin [EE]. Secure with Metal Pin End Cap
[KK]. Repeat with other side.
Take the [2] Large Pins with Hole [EE] and insert each one
into the hole which is below cross support bolt. Insert pin
through inside of base and through other side as shown be-
low. Secure pin [EE] with “C” Washer by sliding “C” washer
over and onto Pin slot which is located right where Pin and
Side Support meet. PLEASE NOTE: This is difficult to
accomplish. You must use a flat screwdriver to push “C”
washer into slot.
Repeat with other A-Base assembly on other side.
First by sliding Channelled Side Support [D] down into A-Base
assembly, then continue by inserting Lower Support & Rod
[F] into Channel in Side Support [D] making sure threaded
rod goes all the way through A-Base assembly, this time
securing with large washer [BB] and Lever [AA].
See photos below.
Take [1] Male Knob [DD] and attach to Pin end. Screw in to
tighten. Repeat with other Adjustment Rod.

Assembly Instructions continued:
STEP 10] Attaching Top Braces
PLEASE NOTE:
Correct attachment of Drawing Top Braces will have
large holes on Drawing Top Brace facing downward.
STEP 11] Turning Base over
PLEASE NOTE: BEFORE TURNING BASE OVER
ONTO DRAWING BOARD: MAKE SURE DRAWING
BOARD BRACES ARE IN A HORIZONTAL
POSITION AND KNOBS ARE TIGHTENED.
Before securing base of table to Drawing Board top, you must center
the base to the top.
Front Edge of Top
Rear Edge of Top
Center base by measuring 7” in [Measurement Y] from outside
edges of Drawing Board to outside edge of Base Braces and
5-1/8” in from front edge of drawing board to front edge of Base
Brace and 5-1/8” in from rear edge of drawing board to rear edge
of base Brace. See illustration below. Secure using [4] Long
Wood Screws [GG] per Base brace.
Y = 7”
Y = 7”
X = 5-1/8”
X = 5-1/8”
STEP 13] Attaching Tilt Adjustment Rods
to Drawing Board
Use two people with this next step. Lay top on carpeted flat surface.
Carefully turn completed base assembly up and over and place on
top of bottom side of drawing board.
PLEASE NOTE: Both sides of Drawing board can be the bottom
side. Choose best looking for Top Side.
STEP 12] Attaching Base to Drawing Top
Base should look and be positioned to Drawing Board as pictured
below.
Attach to the inside of the Side Support [D] using the [2]
remaining knobs, washers and bolts [F]. Insert bolt through
hole on inside of Drawing top Brace, making sure bolt goes
through side support [D]. Finish by attaching washer and
then female knob.
To make your table top tilt: Loosen the [2] black knobs
(with tilt rods through them), proceed by holding onto
the front edge of the top. Tilt top until desired position is
reached. Tighten [2] black plastic knobs.
STEP 14] Table Top Tilt Adjustments
Attach metal tilting brackets to top using [2] each small wood
screws [II] per bracket as shown above. PLEASE NOTE: Break
Table Top Surface by making a small hole in top surface where
screw will go in with hammer and a nail.
To adjust the height of your table, loosen the lever slightly.
PLEASE NOTE: When loosening the lever, the table
will want to lower because of the weight of the top.
Carefully, loosen lever and support table top with
hands and lower or raise until desired height. Re-
tighten Lever to secure. This adjustment is safest with
another adult helping.
STEP 15] Table Height Adjustment
D
G
F
Attach
Bracket on
Tilt
Adjustment
Rods into
Top
Created July 06 - RPI
Pg. 4
When attaching the [2] Drawing Top Braces [G], position the
drawing board brace in the position shown here: