Habitat Venice 450/9071 User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Venice - Large Corner TV Unit
Assembly Instructions - Please keep for future reference
ALR3254
450/9071
459/9641
Width - 119.8cm
Depth - 39.19cm
Height - 51.2cm
Issue 1 - 13/10/15

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 25kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: You must secure
this unit to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
strap supplied
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver

Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below When applicable, remove any
protective film before use
2
80% x 3
90% x 1 1
2
Side (DF5748)
(47.7 x 23mm) x 2
Horizontal (DF5751)
(112.4 x 35.2cm) x 2
Plinth (DF5750)
(112.4 x 9.6cm)
Left Drawer Front (DF5752)
(55.9 x 20cm)
Top (DF5746)
(119.8 x 39.1cm)
Top Divider (DF5755)
(18 x 35.1cm)
Lower Divider (DF5753)
(17.1 x 35.1cm)
Back (DF5749)
(47.7 x 58.6cm)
Right Drawer Front (DF5754)
(55.9 x 20cm)
Left Drawer Side (W210-124LH)
(21 x 12.4cm) x 2
Right Drawer Side (W210-124RH)
(21 x 12.4cm) x 2
Drawer Back (W522-124)
(52.2 x 12.4mm) x 2 Drawer Base (T533-207)
(53.3 x 20.7mm) x 2
3
4
5
6
7
8 9
10 11
12
13

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
Metal dowel (F901) x 18
C
D E
Large locking
nut (F900) x 14
F
G
Hollow core
locking nut
(F892) x 4
I
Small locking
nut (F3) x 4
H
Knock-in Peg (F171GY) x 8
Drawer runner (F307) x 4
J K
P
L
M
Wedgefix (F639) x 4
Large wooden dowel (F40) x 2 Wooden dowel (F22) x 6
Small metal dowel (F893) x 4
45mm Screw (F65) x 4 40mm Screw (F910) x 4 19mm Screw (F461) x 4
9mm Screw (F73) x 8 9mm Screw (F74) x 4
NO
Handle (FBARH128) x 2

8 9
Assembly Instructions
4
Step 1
A
B
A
B
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts and .
Note: Tighten the metal
dowels up fully against
the panels.
A
8 9
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
B
10
11
Attach the drawer
sides to the drawer
frontS
Push a left drawer side .
and a right drawer side .
onto the back of each
drawer front and .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
10
11
8 9
B
B
10
11
B
BB
10 11
A
A
10
11
A
A
Note: The right drawer front
has a small identification hole.
8 9
x 2
x 2
x 2

O
F
F
Assembly Instructions
5
Step 4
8 9
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front and .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 7
13
10 11
8 9
12
10 11
13
12
12
F
10 11
F
13
10
11
10
11
13
12
F
I
I
I
Fit the wedgefixes
Turn the 2 drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
I
x 2
x 2
x 2
x 2
L
L
Step 6
Attach the handles
Attach a handle to
each of the drawer fronts
. and using screws
. .
L
8 9
O
8 9

Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 8
A
A
A
A
Prepare the top
Screw 4 metal dowels
into the top .
Screw 4 small metal
dowels into the holes
on the top .
Note: Tighten metal
dowels up fully against
the panels.
E
A
2
E
2
E
E
E
E
2
C
C
C
H10mm
H
Prepare the top divider
Insert 2 large locking
nuts into the
top divider .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the top divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
H
H
Step 9
C
A
Fit the top divider to
the top
Push the top divider
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top divider .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4
2
C
C
4
C
4
4
4
Step 10
4
2

Fit a horizontal
Attach a horizontal to
the top divider using
2 screws .
Assembly Instructions
7
Step 11
Step 12
Step 13
C
C
C
C
Prepare the 2
horizontals
Insert 4 large locking
nuts into each of the
2 horizontals .
C
3
3
4
K
K
3
4
x 2
K
G
G
Fit the 2 large wooden
dowels
Gently tap the 2 large
wooden dowels
through the horizontal
and into the top divider
. until they ‘’bottom
out’’.
G
3
4
3
4
3
Note: Support the
horizontal until the right
side has been fitted.

Assembly Instructions
8
Step 14
Prepare the right side
a: Place a runner
onto one of the sides .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the side .
c: Screw 5 metal
dowels into the side
. .
Push 2 hollow core
locking nuts into the
side , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
D
DD
P
1
M
P
M
a:
b:
c:
B
1
D
1
D
D
1
M
P
M
M
P
D
A
A
A
A
A
D
1
1
1

Assembly Instructions
9
Step 15
3
Fit the right side
Push the right side
onto the top and the
horizontal .
The 2 small metal dowels
. fitted to the top
must slide into the top of
the 2 hollow core locking
nuts fitted to the right
side . .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
1
2
3
E2
D
1
D
1
2
1
C
3
D D