Elo TouchSystems E421325... User manual

© Copyright 2021 Elo Touch Solutions, Inc. 1
E421325 ELO-STA N D -SELF-SERVICE-15-22-FLOOR-TOP4
E797162 ELO-STA N D -SELF-SERVICE-15-22-FLOOR-BASE
ASSEMBLY INSTRUCTIONS, ELO SELF SERVICE STAND
Revision BQIG600185

© Copyright 2021 Elo Touch Solutions, Inc. 2
Contents for Kit: E421325 ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP4
Tie-wrap
Qty. 3
Hardware
Bag AQty.10 SCREW, M4X8, PAN-HEAD,
CROSS-RECESS
Bag BQty.4 SCREW, M4X8, FLAT-HEAD,
CROSS-RECESS
Bag CQty.3 SCREW, M3X8, PAN-HEAD,
CROSS-RECESS
Bag DQty.4 SCREW, 3mm X8L,
THREAD-FORMING, PAN-HEAD
Bag KQty.6 SCREW, M5X10, FLAT-HEAD,
CROSS-RECESS
Bag LQty.4 SCREW, M4X6, PAN-HEAD,
CROSS-RECESS
Bag MQty.4 SCREW, M4X18, PAN-HEAD,
CROSS-RECESS
Bag NQty.4 SCREW, M4X12, PAN-HEAD,
CROSS-RECESS
Bag SQty.3 SCREW, M4X5, PAN-HEAD,
CROSS-RECESS
Bag TQty.4 SCREW, M4X30, FLAT-HEAD,
CROSS-RECESS
Bag UQty.1 DOUBLE-SIDED FOAM TAPE
Floor-Head Assembly
Qty. 1
Display Bracket, Windows
Qty. 1
Display Bracket, Android
Qty. 1
USB Hub
Qty. 1
Straps
Qty. 3
Panel Hardware
Qty.2 SCREW, M6X14, PAN-HEAD, CROSS-RECESS
Qty.2 BACKER BOARD SPACER
Qty.2 THUMB SCREW

© Copyright 2021 Elo Touch Solutions, Inc. 3
Contents for Kit: E797162 ELO-STAND-SELF-SERVICE-15-22-FLOOR-BASE
Floor Base
Qty. 1

© Copyright 2021 Elo Touch Solutions, Inc. 4
X4
Assemble tower to base
plate using (4) screws
from bag “K”.
12
•Remove and save the (4) screws on the left and right of the stand
front cover.
•Pull off the silver cover and set aside.
•Add (2) remaining screws from bag “K” to bottom front of stand.

© Copyright 2021 Elo Touch Solutions, Inc. 5
Remove and save (2) screws on rear of Head, pull out printer tray.
3

© Copyright 2021 Elo Touch Solutions, Inc. 6
(Power strip shown available from McMaster-Carr, item
#7361K43)
•Add power strip brackets (supplied with power strip) using (2)
screws from bag “L”.
•Hook one side of power strip onto brackets then push to snap down.
Add power bricks into tower using provided straps.
54

© Copyright 2021 Elo Touch Solutions, Inc. 7
Remove and save (2) screws, open cover of Display Bracket;
pivot out and fix prop.
Gap
67
Add (2) screws from bag “A”; leave ~3mm (1/8”) gap
(for Display Bracket).
Choose Android or Windows Display Bracket
For 15” or 22” monitor, use Android Display Bracket
Android Display Bracket shown above

© Copyright 2021 Elo Touch Solutions, Inc. 8
•Assemble Display Bracket onto Head.
•Position “A” for 15”, 22” in landscape.
•Position “B” for 15” in portrait
•Position “C” for 22” in portrait
•Add (2) screws from bag “A” at bottom holes.
8
A
B
C
•Assemble USB Hub.
•Add (2) screws from bag “S”; leave ~3mm (1/8”) gap for USB
bracket to slide on; tighten screws.
9
For Android, skip to step 15
For monitors, skip to step 17
For Windows, skip to step 20
For Android Slate, skip to step 10

© Copyright 2021 Elo Touch Solutions, Inc. 9
10
Top Landscape
•Add (2) screws from bag “L” to top 75mm VESA
positions. Leave ~3mm (1/8”) gap for mounting to
display bracket.
•Connect Slate Hub to Slate and attach cable cover
before proceeding.
Add tie-wrap
Route Slate Hub through display bracket and head. Mount Slate, add (2)
screws from bag “L” to bottom 75mm VESA positions. Add tie-wrap as
shown. Tighten VESA screws to 12 in-lb (1.4 N-m).
Android Slate: Landscape
(For Portrait, skip to step 12)
11
Skip to step 14
Note: EMV Cradles are not compatible with Android Slate
in landscape orientation.

© Copyright 2021 Elo Touch Solutions, Inc. 10
12
Top Portrait
Add tie-wrap
•Add (2) screws from bag “L” to top 75mm VESA
positions. Leave ~3mm (1/8”) gap for mounting to
display bracket.
•Attach Slate Hub and cable cover before mounting
displays on stand.
•Route Slate Hub through display bracket and head.
•Mount Slate, add (2) screws from bag “L” to bottom 75mm VESA positions.
Add tie-wrap as shown.
•Tighten VESA screws to 12 in-lb (1.4 N-m).
Android Slate: Portrait
13
If using an EMV Cradle, follow those instructions
before proceeding.

© Copyright 2021 Elo Touch Solutions, Inc. 11
Apply double-sided foam tape from bag “U” to back of Slate Hub and attach to back of tower approximately
where shown. Route LAN cable through tower base. Connect LAN and power supply to Slate Hub.
14
Skip to step 28

© Copyright 2021 Elo Touch Solutions, Inc. 12
15
Top Landscape
Cable
direction
•Add (2) screws from bag “L” to top 100mm VESA
positions. Leave ~3mm (1/8”) gap for mounting to
display bracket.
•Remove cable cover(s) before mounting displays on
stand.
•Mount I-Series, add (2) screws from bag “L” to bottom 100mm VESA positions.
•Route power, LAN cables through bottom of stand head. Route USB Hub
cable or other USB if used. Tighten VESA screws to 12 in-lb (1.4 N-m).
Add tie-wrap
Android or 15”/22” Monitor: Landscape
(For Portrait, skip to step 17)
16
Skip to step 28
If using an EMV Cradle, follow those instructions
before proceeding.
Note: EMV Cradles are not compatible with
monitors in landscape orientation.

© Copyright 2021 Elo Touch Solutions, Inc. 13
17
Top Portrait
Cable
direction
Add tie-wrap
For 22” Monitor,it is recommended to use centering plate
(P/N E698263) to center monitor on stand. A ttach centering
plate to 22” monitor before proceeding.
•Add (2) screws from bag “L” to top VESA positions.
Leave ~3mm (1/8”) gap for mounting to display bracket.
•Remove cable cover(s) before mounting displays
on stand.
Mount i-Series, add (2) screws from bag “L” to bottom VESA positions.
Route power, LAN cables through bottom of stand head. Route USB Hub
cable or other USB if used.
Android or 15”/22” Monitor: Portrait
18
For monitor, continue to step 19
For Android skip to step 28
If using an EMV Cradle, follow those instructions
before proceeding.

© Copyright 2021 Elo Touch Solutions, Inc. 14
Optional: Mount Backpack 4.0 to tower bracket as shown using
(4) screws from bag “T”. To improve Wi-Fi signal use antenna
extension cables (Amphenol RF P/N 095-902-538-024,
available from Digikey or Mouser).
Remove antennas from Backpack, attach (2) extension cables to
Backpack antenna connectors. Attach male end of extension
cables to holes in tower rear, then attach antennas to cable
connectors.
19
Skip to step 28

© Copyright 2021 Elo Touch Solutions, Inc. 15
20
Windows Landscape
(For Portrait, skip to step 24)
15” Landscape
15”: add (2) screws from bag “M” to top 75mm VESA positions.
22”: add (2) screws from bag “N” to top 75mm VESA positions.
Leave ~3mm (1/8”) gap for mounting to display bracket.
22” Landscape
21
Route power cable from I-Series through bottom of stand,
through openings in the mount bracket as shown.
If using an EMV Cradle, follow those instructions before proceeding.

© Copyright 2021 Elo Touch Solutions, Inc. 16
Skip to step 28
22
Place I-Series on surface near stand head, within reach of
cable. Remove cable door (A), plug in power cable (B)
and replace cable door (C) as shown.
A
C
B
Add tie-wrap
Mount I-Series, then add bottom VESA screws:
Route, LAN cable through bottom of stand head. Route USB
Hub cable or other USB if used.
23
Add (2) screws from bag “M” (15”) or bag “N” (22”) to bottom
75mm VESA positions.

© Copyright 2021 Elo Touch Solutions, Inc. 17
22” Portrait
15” Portrait
15”: add (2) screws from bag “M” to top 75mm VESA positions.
22”: add (2) screws from bag “N” to top 100mm VESA positions.
Leave ~3mm (1/8”) gap for mounting to display bracket.
24 25
Windows Portrait
Route power cable from I-series through bottom of
stand, through openings in the mount bracket as shown.
If using an EMV Cradle, follow those instructions before proceeding.

© Copyright 2021 Elo Touch Solutions, Inc. 18
26 27
A
C
B
Place I-Series on surface near stand head, within reach of
cable. Remove cable door (A), plug in power cable (B)
and replace cable door (C) as shown.
Add tie-wrap
Route, LAN cable through bottom of stand
head. Route USB Hub cable or other USB
if used.
Mount I-Series, then add bottom VESA screws:
15”: add (2) screws from bag “M” to bottom
75mm VESA positions.
22”: add (2) screws from bag “N” to bottom
100mm VESA positions.

© Copyright 2021 Elo Touch Solutions, Inc. 19
Add (2) screws from bag “C” to printer tray; use Star printer
bracket to set depth of screws than remove Star bracket.
Continue to step 29 for Star printers.
For Epson TM-T88, skip to step 32.
28 29
If using printer, remove cover to add printer.
If no printer, skip to step 33.

© Copyright 2021 Elo Touch Solutions, Inc. 20
Add (4) screws from bag “D” to attach printer to the tray.
32
Add Star printer bracket to printer; refer to Star instructions.
Add Star printer with bracket to printer tray. Secure
printer to printer tray using third screw from bag “C”.
31
30
Epson TM-T88
Skip to step 33