EM E30 User manual

IMPORTANT SAFETY INFORMATION:
Always read this manual rst before aempng to install or use this replace. For your safety, always comply with all warnings and safety instrucons contained in this
manual to prevent personal injury or property damage.
Please note: This product is only suitable for well insulated spaces or occasional use.
E-Series-170420
MODELS: E30 / E32H / E40 / E60 / E70
Installation Manual

When using electrical appliances, basic precauons should always be followed to reduce the risk of re, electric shock, and injury to persons, including the following:
① Read all instrucons before using this electric replace.
② This replace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operaon. DANGER: High tem-
peratures may be generated under certain abnormal condions. Do not parally or fully cover or obstruct the front of this heater.
③ Extreme cauon is necessary when any heater is used by or near children or invalids and whenever the unit is le operang and unaended.
④ Young children should be supervised to ensure that they do not play with the appliance.
⑤ The appliance is not intended for use by young children or inrmed persons without supervision.
⑥ Do not operate the unit aer it malfuncons. Disconnect power at the service panel and have the unit inspected by a reputable electrician before reusing.
⑦ If the supply cord is damaged, it must be replaced by the manufacturer, or its service agent, or a qualied person in order to avoid a hazard.
⑧ Do not use outdoors.
⑨ Never locate replace where it may fall into a bathtub or other water container.
⑩ To disconnect the replace, turn the controls o, and turn o power to heater circuit at main disconnect panel.
⑪ Do not run the cord under carpeng. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from trac area and where it will not be tripped over.
⑫ Do not locate the heater immediately below a xed socket-outlet.
⑬ Do not insert or allow foreign objects to enter any venlaon or exhaust opening as this may cause an electric shock or re, or damage to the heater.
⑭ To prevent a possible re, do not block air intakes or exhaust in any manner.
⑮ All electrical heaters have hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint, or ammable liquids are used or stored.
⑯ Use this replace only as described in this manual. Any other use not recommended by the manufacturer may cause re, electric shock or injury to persons.
⑰ Do not change the plug in any way. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
⑱ Do not burn wood or other materials in the electric replace.
⑲ Do not strike the replace glass.
⑳ Always use a cered electrician should new circuits or outlets be required.
㉑ Always use properly grounded, fused and polarized outlets.
㉒ Disconnect all power supply before performing any cleaning, maintenance or relocaon of the unit.
㉓ When transporng or storing the unit and cord, keep in a dry place, free from excessive vibraon and store so as to avoid damage.
NOTE: Changes or modicaons not expressly approved by the party responsible for compliance could void user's authority to operate the equipment.
IMPORTANT INSTRUCTIONS:

INSTALLATION REQUIREMENTS:
Review and consider all of the following condions before installaon:
Ensure installaon does not allow the electric replace to be in direct contact with building vapor barrier or insulaon and meets all local building code.
A 15 Amp, 120 Volt circuit is required. A dedicated circuit is preferred but not essenal in all cases. A dedicated circuit will be required if, aer installaon, the circuit breaker trips or fuse
blows on a regular basis when the heater is operang. Addional appliances on the same circuit may exceed the current rang of the circuit breaker.
Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of
re, electric shock or injury to persons. Construcon and electrical outlet wiring must comply with local building codes and other applicable regulaons to reduce the risk of re, electric
shock and injury to persons.
WARNING: To reduce the risk of re, do not store or use gasoline or other ammable vapors or liquids in the vicinity of the heater.
1. Select a locaon that is not suscepble to moisture and is away from drapes, furniture and high trac.
2. For ease of electrical hook up you may wish to locate the replace near an exisng outlet (for plug-in convenience).
3. Remove electric replace, front glass and hardware from the box and remove all packaging materials before installaon.
4. Store the replace in a safe, dry and dust free locaon unl you are ready to install the replace.
Grounding Instrucons:
This product must be grounded. If it should malfuncon or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.
This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
DANGER: Improper connecon of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualied electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the product – if it will not t the outlet, have a proper outlet installed by a qualied electrician.
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug in Figure 1. Make sure that the product is connected to an outlet having the same
conguraon as the plug. No adapter should be used with this product.
WARNING: Do not aempt to wire your own new outlets or circuits. To reduce the risk of re, electric shock or injury to persons, always use a licensed electrician.
Figure 1.

This product has been designed to be installed into a plaster board, drywalled, or exisng masonry chimney breast.
Please note that any GF2 models from the e-series range are not suitable to be installed into a exisng chimney breast.
Please seek advice from a professional, with reference to the structural integrity of the installaon site.
if the products is to be installed into a open chimney or ue, it is important that the chimney/ue is blocked o to prevent any up/down draughts and falling debris which could restrict
and alter the airow to the product.
It is also important to ensure that the product has a minimum internal clearance directly above and below the product of 50mm, this is to ensure that the product can circulate the re-
quired airow for the heater unit.
The product should never be sealed into a opening with the use of silicones or adhesives as this can also alter the airow and hinder any further servicing of the product.
INSTALLATION METHOD:
Installing Product:
Each E-Series product is supplied complete with one or more wall mounng brackets. (Dependent on Model)
Establish the desired nished height from oor level to the boom of the plaster kit of the product.
Fix the wall bracket to the wall ensuring to use the correct hardware xings given the wall construcon, dry wall or Solid Wall.
Li and hook the product onto the wall bracket and secure using the wall brace brackets.
Once the product is secured to the wall and connected to the power supply, the false construcon such as plaster board wall or chimney breast can be formed around it.
It is important to allow for the nished face board when seng the depth of the frame construcon.
It is essenal to include header/Lintel at the required height to ensure the appliance does not support the weight of the nished wall.
Prepare the Cut-Out in the Plaster-board or Finishing Board, and install ensuring that the plaster kit edges are ng to the inside of the Cut-out of the board.

MODEL: WDH
E30 745MM 185MM 475MM
E32h 835MM 305MM 790MM
E40 1065MM 305MM 560MM
E60 1565MM 305MM 560MM
E70 1785MM 305MM 615MM
The below table contains the minimum opening sizes required to house the product.
The below table contains the nal nished opening sizes once the product has been installed.
MODEL: WDH
E30 745MM 185MM 475MM
E32h 835MM 305MM 790MM
E40 1065MM 305MM 560MM
E60 1565MM 305MM 560MM
E70 1785MM 305MM 615MM
Please refer to technical specicaon table for further informaon, with reference aperture measurements.
Please see Figure 1: as a example of a installaon.
Figure 1:

The Appliance is operated using the E-Touch App Control.
The App Control can be used on either OS or Android operang systems.
To obtain the App please visit either the OS App Store Or Google Play and follow the on screen instrucons.
Screen shot taken from Apple App Store. Home Screen shot taken from E-Touch App

Product Operaon:
The appliance is operated by the e-touch App, the main standby power switch to the e-series product is located to the right of the heater outlet, which is marked with a light bulb image, to
acvate the product, this switch must be switch to the “ON” posion.
The rst me the e-series product is acvated both the illuminaon and heater will funcon, to switch the heater “O” simply reduce the Room Temperature down to 10 degrees on the
App control.
(Heater unit cut-out) (This is a safety feature, to safe guard against further damage to the product).
If the airflow is restricted the heater will automatically turn off. This is can occur due to incorrect installation or obstruction.
To reset the heater function:
Please note that both the eect fan and heater fan omit a low decibel noise, both of which are normal operang characteriscs.
•isolate from the mains power supply.
•Leave product to cool.
•Aer a suitable cooling down period, remove the obstrucon if obstructed, and check installaon.
•Aer 10 minutes the thermo switch (cut-out) in the heater will reset.

LOG LENGTH
A260MM
B370MM
C230MM
D185MM
E190MM
F390MM
E40—LOG LAYOUT
E60 & E70—LOG LAYOUT
LOG SET
Please Note: The images shown are suggested Log layouts, the log sets can
be arranged to personal preference.

European Home
30 Log Bridge Road
Bldg 300, Unit 303
Middleton
MA 01949
United States
European Home Warranty
Electric Modern Family of Products
European Home warrants all Electric Modern electric fireplaces against defects in materials and workmanship for a period of TWO (2) YEARS from the date of original retail purchase.
If a defect exists, European Home will, at its option, either (1) repair the product at no charge, using new or refurbished re-placement parts or (2) exchange the product with one which
is new or which has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product. A replacement product/part assumes the
remaining warranty of the original product or ninety (90) days from the date of replacement or repair, whichever provides longer coverage for you. When a product or part is
exchanged, any replacement item becomes your property and the replaced item becomes the property of European Home. Nothing in the above shall be deemed to imply that this
warranty shall apply to work which has been abused or neglected or shows evidence of changes or modifications by others with or with-out permit, damages caused by the acts of
God, building settlement or moving, fire or vandalism. In addition, installation of this product that varies from the requirements stated in the
European Home is a division of Europa Ja, Inc.