Emerge SmartSurge User manual

USER'S GUIDE
USER'S GUIDE
Thank you for purchasing this SmartSurge. Smart Power Systems
is dedicated to developing and manufacturing the highest
performance power protection and filtration devices for your
electronic equipment. Proper use of this device will provide the
protection needed for your connected equipment.
PN16001220 Rev.06/22
Dedicated Surge Protector
SmartSurge

DESCRIPTION
Use this user's guide for the following products:
Modem & Data Protection (model dependent)
Protection is extended to your phone and network lines with the addition of RJ11 and RJ45 jacks
on the SmartSurge unit, creating ideal protection for Fax/Internet/Network users. Power
surges can pass to the connected equipment through phones lines and network cables.
CAUTION
CAUTION
CAUTION
CAUTION
• Use only in dry locations indoors.
• Avoid dropping the unit.
• Only plug the SmartSurge into a three pronged grounded outlet. This unit is not to be used
with any type of ground “lift” or pin eliminator.
• Do not open the SmartSurge unit, there are no serviceable parts inside. Opening the unit
will void your warranty.
This device features an internal protection that will disconnect the surge protective component
at the end of its useful life but will maintain power to the load now unprotected. If this situation
is undesirable for the application, follow the manufacturer's instructions for replacing the device.
Do not install this device if there is not at least 10 meters (30 feet) or more of wire between the
electrical outlet and the electrical service panel.
Risk of Electric Shock. Do not plug into another relocatable power tap.
FEATURES
If you have any questions call us at our Tech Support line toll free
1-800-772-7633 or email us at [email protected]
MODEL /
PART NUMBER
120V/15A, one 5-15R outlet
120V/15A, one 5-15R outlet, RJ11
120V/15A, one 5-15R outlet, RJ45
120V/15A, one 5-15R outlet, RJ11 + RJ45
SS15
SS15-T
SS15-N
SS15-TN
(Phone + Network Protection)
(Phone Protection)
(Network Protection)

1.Turn off and un-plug equipment to be protected from wall outlet.
2. Plug the equipment into the SmartSurge unit.
3. Plug the SmartSurge unit into grounded wall outlet.
4. Your equipment is now fully protected. Place the SmartSurge where monitoring lights
can be observed.
Installation of SmartSurge
Installation for Protection for Telephone Line
Installation for Protection for Network Cable
TELEPHONE
1. Unplug the equipment's telephone cable from the wall jack and plug into the RJ11 "OUT"
on the SmartSurge.
2. Plug the provided telephone cable to the RJ11 jack "IN" on the SmartSurge.
3. Plug the other end of the telephone cable into the RJ11 wall jack.
CAUTION: - Never install telephone wiring during a lightning storm.
- Disconnect telephone line at the network interface before installing the secondary
protector.
- Intended for indoor use only.
Telephone Line Protection clamping voltage 250-350 vdc.
Use the Standard CAT 5 Network Patch cord when using the Network protection RJ45 circuit.
Power Cord
Power Cord
IN
IN
OUT
OUT Phone Wall Jack
Network Jack/ HUB
Connected
Equipment with
Network Jack
The green light confirms power exists
at the output receptacle.
GREEN LIGHT
1. Unplug the equipment's network cable from the wall RJ45 network jack and plug into the RJ45
"OUT" on the SmartSurge.
2. Plug the provided CAT5 cable to the RJ45 jack "IN" on the SmartSurge.
3. Plug the other end of the CAT5 cable into the wall RJ45 network jack. Your equipment is now
fully protected. Place the SmartSurge where monitoring lights can be observed.
IMPORTANT: The SmartSurge is designed to be compatible with a GFCI (Ground Fault
Circuit Interrupter), however, during plug in the GFCI might trip. Press the reset button to
restart the circuit.

IMPORTANT
If for any reason you need to return the SmartSurge unit to the manufacturer, you
should obtain an RMA (Return Material Authorization) number before returning the unit.
To request an RMA number please call 1-800-772-7633 or visit the website at
www.smartpowersystems.com/main/rma.htm
7409 Railhead Ln. - Houston, Texas 77086 - Tel:[phone] - Fax:[phone]
E-mail: [email protected] - www.smartpowersystems.com
TBF™ (TRANSFORMER-BASED FILTER) POWER FILTERS
Considered to be one of the most significant developments in the power protection industry.
TBF™ Filters contain innovative technology that combines Surge Suppression and Noise
Isolation which filters the noise on the ground to less than 0.5 Volts (US Patent # 6229682).
Exclusive "POVP" Prolonged Over Voltage Protector (US Patent # 6560086) disconnects the
output power if voltage exceeds 155 volts. Exclusive Smart Technology (US Patent
#5721661) protects microprocessor based equipment against reverse polarity or no ground.
The patented TBF™ filters prevent 90% of the power problems experienced by your POS
system, computer, copier and facsimile machine.
AUTOMATIC VOLTAGE REGULATOR - AVR SERIES
Regulates the voltage to protect equipment against voltage sags and brownouts. Electronic
systems are designed to operate based on a clean and constant supply of AC voltage.
Smart Power Systems' AVR line provides boost & buck capability to eliminate under or over
voltage fluctuations.
UNINTERRUPTIBLE POWER SUPPLIES - UPS SERIES
Smart Power Systems' Uninterruptible Power Supplies (UPS) integrated TBF™ Technology
provide on-line power conditioning.
OTHER POWER PROTECTION PRODUCTS
WARRANTY
Limited Lifetime Warranty
If the Smart Power Systems equipment fails and this failure allows a surge to pass through and
damage the connected equipment, Smart Power Systems will pay for the repair or replacement of
the connected equipment of the original purchaser. Please take the time to register each Smart
Power Systems' product along with the connected equipment devices connected to it within 10
days of date of purchase in order for you to take advantage of this product warranty and connected
equipment protection policy. See our website for more details - www.smartpowersystems.com
$25,000 Connected Equipment Warranty
Smart Power Systems warrants to the original purchaser that the power filters shall be free of defects
in material and workmanship under normal use and service for the lifetime of the original, registered
connected equipment, and Smart Power Systems will repair or replace, at its sole option, any
defective power conditioners free of charge. This warranty is not transferable. See our website for
more details - www.smartpowersystems.com