EMS FireCell FC-610-001 User manual

1 Pre installation 2 Components
Part no Product description
!
4x lid fixing screws Front lid
3
Back box
5 Input wiring
FC-610-001 Wireless Dual Input/Output Unit
Wireless Input Output Unit
Installation Guide
FC-610-001
DUALI/O UNIT
IDENT REV D ATE
FC-610-001
EN300 200-2
0905 !
20K 4K7
CN/O
20K = Red/Bl
4k7= Yellow
EOLResistor
Conguration
ANTENNA
2
1
3 Remove cable entry points 4 Fix to the wall
Use all four circled
fixing positions to
ensure a firm fixing.
Use suitable fasteners
and fixings.
INPUT 1 INPUT 2
IP- IP+ IP- IP+
20k 4k7
CN/O
Drill the cable entry
points as necessary.
Cable glands should
be used.
DO NOT leave
excess cable in the
device.
ON
INPUT1 INPUT2
EXPAN1 EXPAN2
OUTPUT 2
OUTPUT 1
IP- IP+ IP- IP+
3VDC SET RST
N/O COM N/C
3VDC SET RST
N/O COM N/C
Do Not Use
=
Available
Cable Entry
Points
=
Installation must conform to applicable local installation
codes and
should only be installed by a fully trained
competent person.
Ensure that the device is installed as per the site survey.
The use of a non-metallic spacer should be considered if
mounting the device on to a metal surface.
Do NOT Press the Log On button on a pre-programmed
device, as this will cause communication with the Control
Panel to be lost. Should this happen, delete the device from
the system and add it back on.
This device contains electronics that may be susceptible to
damage from Electrostatic Discharge (ESD). Take appropriate
precautions when handling electronic boards.
123
ANTENNA
KEEP CABLES AWAY FROMTHIS AREA
LOGON
OUTPUT 2OUTPUT 1
3VDC SET RST
INPUT 1 INPUT 2
LED
ENABLE
POWER
INPUT
INPUT
FAULT
CLOSED
0 1
1
64
F-SAFE
N/O COM N/C
IP- IP+ IP- IP+
3VDC SET RST N/O COM N/C
EXPAN1 EXPAN2
RELAY ON RELAY ON
2
4
8
16
32
ON
1 2 3 4 5 6 7 8
012ABC
Fixing position
location within
cavity
6 Output wiring
Two resistor monitored inputs are
available.
Both inputs monitor; closed (alarm),
open and short circuit conditions.
Each input is factory fitted with an
end of line 20 kΩ resistor.
To connect inputs to external
devices, wire as shown below. I.e.
Input 1, using the resistor pack
provided.
If an input is not being used, leave
the 20 kΩ resistor as factory fitted.
EOL
Resistor
Setup
Remote Monitored Device
Note: Max
Cable Length
of 10m
OUTPUT 2OUTPUT 1
N/O COM N/C N/O COM N/C
Two outputs are also available.
Both outputs are voltage
free and rated 2 A at 24 VDC.
WARNING. DO NOT CONNECT TO MAINS.
!
DUALI/O UNIT
FC-610-001
©2021 EMS Ltd. All rights reserved Page 1 of 2 TSD050-99 Iss 15 23/11/2021 AJM

7 Power device
When fitting / replacing batteries; observe correct polarity,
using only specified batteries.
Connect the power jumper across the PIN header.
8 Configuration
Once powered, reassemble the device.
OUTPUT 2OUTPUT 1
3VDC
SET RST
INPUT 1 INPUT 2
LED
ENABLE
PO WER
INPUT 1 INPUT 2
FAULT
CLOSED
0 1
1
64
F-SAFE
N/O COM N/C
IP- IP+ IP- IP+
3VDC SET RST N/O COM N/C
EXPAN1 EXPAN2
RELAY ON RELAY ON
2
4
8
16
32 device
unpowered
(pins unlinked)
device
powered
(both pins linked)
9 LED operation
The device has six indication LEDs. Pressing the LED enable button
enables their illumination for 10 minutes before automatically
timing out.
2x Input Fault: YELLOW LED ON = FAULT
2x Input Closed: RED LED ON = ACTIVE
2x Output: RED LED ON = ACTIVE
CLOSED
FAULT
INPUT 1
INPUT 2
Input 2
LEDs
Input 1
LEDs
Output 1 LED Output 2 LED
Operating
temperature -10 to +55 °C
Storage
temperature 5 to 30 °C
Humidity 0 to 95% non-condensing
Supply 6x AA alkaline (Panasonic LR6AD Powerline / Varta
4006 Industrial)
CAUTION!
Fitting of an incorrect battery type invalidates the product certification and
may result in poor performance.
Output rating 2 A at 24 VDC
IP rating IP65
Operating frequency 868 MHz
Output transmitter
power Auto adjusting 0 to 14 dBm (0 to 25 mW)
Dimensions
(W x H x D) 120 x 240 x 60 mm
Weight 0.95 kg
Location Type A: For indoor use
2012/19/EU (WEEE directive):
Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the
European Union. For recycling, return this product to
your local supplier upon purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see
www.recyclethis.info
Dispose of your batteries in an environmentally
friendly manner according to your local regulations.
European Union
directives EMS declares that this device is in compliance with
Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following
internet address: www.emsgroup.co.uk
Approved to EN54-18:2005. Fire detection and fire alarm
systems. Part 18: Input/output devices.
EN54-25:2008. Incorporating corrigenda
September 2010 and March 2012. Fire detection
and fire alarm systems. Part 25: Components using
radio links.
Certification
Certification body
CPR DoP 0359-CPR-0039
Carrier Manufacturing Polska Sp. Z o.o. Ul. Kolejowa
24. 39-100 Ropczyce, Poland
Manufacturer
Year of
manufacture See devices serial number label
0905
10
Specification Regulatory Information
©2021 EMS Ltd. All rights reserved Page 1 of 2 TSD050-99 Iss 15 23/11/2021 AJM
The device’s loop address is configured within the user interface’s
menu structure.
Refer to the programming manual for full programming details.
Free to download from
www.emsgroup.co.uk
FireCell = MK98
Fusion = TSD062
WZM = TSD143