Endon Laughton BLU User manual

1
The Light pack contains:
Adjustable light fitting and mounting bracket.
Terminal connection block(s).
The following tools may be required:
Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.
INSTRUCTION MANUAL
This product is only suitable for connection to a 240V~50Hz supply in accordance with current IEE
wiring Regulations and should be installed in accordance with local Building Regulations and is for
Domestic indoor ceiling use only and is not suitable for a Bathroom location.
The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp
miniature circuit breaker).
If in doubt we recommend you contact a qualified electrician. Before installing your light fitting
always:
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit
breaker before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.
Never fit bulbs of a higher wattage or of a type other than those specified on the label as this may
cause overheating and damage the fitting.
This product contains glass parts – be careful during handling and maintenance to avoid breakage.
The bulb becomes hot during use so please switch off and allow 10 minutes to cool before replacing
bulbs or cleaning the fitting.
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
If any modification is made it will invalidate the warranty and may render the product unsafe.
Before you start
Please read these instructions carefully before fitting your new light and retain for reference.
Make sure that there are no pipes or cables beneath the mounting surface.
Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly.
Make sure all screws / nuts, including electrical connections etc are fully tightened before use.
This type of Light Fitting may be connected to a Dimmer if a Tungsten incandescent bulb is used. If
a CFL/LED type bulb is fitted then these cannot (generally) be controlled by a dimmer.
Laughton BLU / GR / GRY / YE – Pendant.
Safety Warnings

2
Assembly/ User Instructions
These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.
Endon lighting
LS9 0SE
20150811
R10 48
Diagram A
1. Decide on the position of the light fitting / or remove
existing light fitting. Take a note of the position of the
electrical connections. Ensure there is a solid
mounting surface, preferably a wooden joist or joist
bridge to support the weight of the light fitting.
2. See Diagram A. Remove the fixing bracket, by
undoing the 2 bracket screws (1), retain these for re-
use.
3. Use the fixing bracket (2) as a template to mark the
screw holes, mark the screw holes and secure to the
ceiling with the screws (3) supplied.
4. Diagram B. The height of the pendant may be
reduced by shortening the cable. If you want to
reduce the overall length of the fitting it is essential
that this is done before the fitting is mounted to the
ceiling and / or connected to the mains supply. We
recommend that the minimum length of cable below
the ceiling cup is 100mm. The cable must now be
shortened and the excess cable cut and re-
connected to the terminal block. To do this, firstly
take a note of the position of the cables in the
terminal block, undo the screw in the cable grip (4)
(below the ceiling cup) then feed the cable up
through the ceiling cup entry hole, cut off the excess
cable and re-connect to the terminal block. Tighten
the cable grip screw onto the cable.
5. Support your fitting and connect the house wiring to
the terminal block (5) – see also WIRING DETAILS.
NOTE: This is a Class II fitting and must not be
earthed. If you have any earth cables make sure that
they are connected to each other – to maintain earth
continuity throughout your property – and wrap the
earth terminal and connections in 2 layers of good
quality insulation tape and keep them away from the
terminal connections of the fitting. Open the terminal
block box and take out the long tailed grommet, sliding it
up the house supply cable. Cut and strip the cable and
connect it to the terminal block as shown. Close the box.
The additional single terminal block connector is used for
the “loop” wires of the “Ring Circuit”. There may be more
than one set of cables in the “loop” connections. This
additional connector must be wrapped in 2 layers of good
quality insulation tape to prevent the conductors touching
the main terminal block connections or the metal of the
fitting. If there is a “Ring Circuit” and you do not
understand the connections you must consult an
electrician.
6. Re-position the fitting over the bracket and secure
with the 2 bracket screws, removed in 2 above.
Make sure that all the internal cables and
connections are inside the back plate taking care not
to trap or strain the internal cables.
7. Fit the bulb (6) – not supplied - into the lamp holder.
NOTE: Never fit bulbs of a higher wattage than
those specified on the label (as these may cause
overheating and damage the fitting).
8. Turn on the power and test.
Diagram B
Wiring details