enertik Warm Series User manual

Warm Series Ultra-thin
Fan Coil User Manual

1
CONTENT
I. Product Features.................................................................................................... 2
II. Instruction for use.................................................................................................. 2
1. Safety Warning.................................................................................................2
2. Operation instruction of remote controller...................................................3
III. Installation instructions and technical parameters......................................... 5
1. Technical parameters......................................................................................5
2. Installation guidelines and piping specifications........................................ 6
3. Unit wiring diagram and wireless water pump connection instructions.7
IV. Daily maintenance................................................................................................9
1. Cleaning.......................................................................................................... 9
2. Maintenance.................................................................................................10
3. Fault codes and descriptions.................................................................... 10
Please read this manual carefully before using the unit, otherwise we
will not be responsible for any loss, and please keep it properly for your
reference.
Applicable models：Warm Series BC-FCV-FP500.

2
I. Product Features
1. Support warm air in cold winter
2. Matching the decoration,the appearance is fashionable and exquisite
3. High coefficient and energy-saving.
II. Instruction for use
1. Safety Warning(It may cause injures for people or damages for units if do
not operate as following )
Heat pump fan coil
must be installed by
Professionals.
The installation or
maintenance of the
unit must ensure
that the ground wire
is grounded safely
and reliably, and
live operation is
strictly prohibited.
Must use
220V~50Hz
individual power
supply.
Do not use mobile
socket, damaged
Power cord and
socket.
In case of unit
abnormality, please
cut off the Power
supply immediately
and contact our
personnel for
handling .
Do not put the
inflammable and
explosive material
near the unit.
Do not repair,
maintain, dismantle
or transform the
unit without
permission .
Do not touch the
plug with wet
hands.
Do not put your
hands or anything s
close to the air
outlet and blades.

3
2. Operation instruction of remote controller
2.1.Remote controller diagram
2.2.Names and function of each key of the remote controller
"ON/OFF" key
Press ON/OFF key to start/stop the heat pump fan coil.
"Mode" key
Press mode key to select different modes in order:Cooling mode,dehumidification mode,air supply
mode,heating mode
"Up/Down" key
Press "UP" key to set the temperature to rise by 1℃ every time, and press "Down" key to set the
temperature to fall by 1℃ every time. The range of setting temperature is: 16 ~ 31℃; Press and hold
"UP" key for 1 second, then set the temperature to increase rapidly; Hold down the "Down" key for 1
second, then set the temperature to decrease rapidly;The keys are invalid under dehumidification
mode and air supply mode.
"Fan" key
Under heating and cooling mode(Automatically):Automatic speed/low speed/mid speed/High
speed.
Air supply mode: Low speed/Mid speed/High speed.
Dehumidification mode: Automatic speed
Sleeping mode: Low speed
"Sleep" key
Press "sleep" key once to start the sleep function, and the wind speed is low.

4
Press "sleep" key again to cancel the sleep function.
Press "sleep" key in the air supply mode is invalid.
When you press the "mode" and "Power" keys to exit the sleep function.
"Timer" key
When the heat pump is turned on,press "Timer" key to set a time for shutdown;When the heat
pump is shutdown,press "Timer" key to set a time for starting up.
Set a timer for shutdown when the heat pump is turned on:
Press the “timer” key for the first time, time setting and time shutdown icon flashing once per
second, then press the "up" key and "down" key to adjust the time
Press the
“ timer ” key for the second time to determine the timing time, and the icon will no longer
flash to display the remaining time of the timing
Press the timing for the third “timer” key to cancel the timing
Set a timer for starting up when the heat pump is turned off:
Press the “timer” key for the first time, time setting and timed shutdown icon flashing once per
second, then press the "up" key and "down" key to adjust the time.
Press the “timer” key for the second time to determine the timing time, and the icon will no longer
flash and display the remaining time of the timing.
Press the timing for the third time key to cancel the timing.
When adjusting the setting time, only the time number will not flash, while other timing icons will
flash. If the "Up/Down" key is not pressed within 10 seconds,exit the timer setting.Timer setting
range:0.5h~24h,the default is 6h(When the timing time is less than 10 hours, increase 0.5h for each
press; When the timing time is more than 10 hours, each press an increase of 1h)
"Super" key
Under the cooling mode, press the "Super" key and the wind speed will be high. Press the "Super"
key again and it will automatically turn into the original state after forced operation for 20 minutes.
Under the heating mode, press the "Power" key and the wind speed will be high. Press the "Super"
key again and it will automatically turn into the original state after forced operation for 20 minutes.
In Power mode, press the "Super" key,"ON/OFF" key and "Mode" keys to exit "Super" mode.
"ECO" key
Press "ECO" key to enter into economic mode.
"Swing" key
Press"Swing" key to turn on the swing air function.
Note: the schematic diagram of the remote control is for reference only. The specific functions are
subject to the actual operation.

5
III. Installation instructions and technical parameters
1. Technical parameters
Model
BC-FCV-FP500
Leakage protection
Class Ⅰ
Rated voltage/frequency
220V/50Hz
Rated air volume
350m³/h
Rated cooling capacity
2350W
Rated heating capacity
3150W
Rated input power
30W
Rated input current
0.14A
Net weight
17Kg
Noise
≤37dB(A)
Maximum allowable pressure
of heat exchanger
≤1.6MPa
Note:
Noise data and power consumption are high wind speed test values;
Cooling operating parameters: Air inlet temperature(DB/WB) 27℃ /19.5℃ , inlet water
temperature 7℃, water temperature difference 5℃. Heating operating conditions: Air inlet
temperature(DB) 21℃, Water inlet temperature 60℃, water flow of both heating and cooling
conditions are the same.
Due to product improvement, the above parameters may be changed, subject to the product
nameplate parameters, without prior notice.

6
2. Installation guidelines and piping specifications
2.1.Reserved distance of air outlet
2.2.Installation guidelines and notes
The unit shall be professionally installed.
In order to eliminate possible accidents caused by handling, the fan coil should be tested for
leakage(1.0mpa) before installation.
Before the installation, check whether the preliminary preparation work is ready, such as water
pipe, wire interface, etc.
When the unit is installed, the connection between the water pipe and the unit is suggested to be
sealed by flexible connection pipe and raw tape. When the pipe is connected, the force should not
be too strong. The torque should not exceed 205.6 N·m to avoid torsional crack and leakage.
The water filter should be installed on the water inlet pipe of the unit to prevent the dirt from
blocking the coil pipe; The exhaust valve shall be installed at the highest point of the waterway
system. Before commissioning and use, the exhaust valve shall be opened to discharge air from
the system tube.
The water pipe of the unit should be equipped with a valve to adjust the water flow and cut off the
water source during maintenance. Pipes should be pre-insulated so as not to affect the heating
effect.
This product is applicable to the standard power supply conditions in mainland China. Before
installation, confirm whether the grid voltage in the area is consistent with the voltage on the
nameplate of the unit, and whether the carrying capacity of the power supply, wires and sockets is
suitable for the input power requirements of the unit.
The user shall not change the power line without authorization. The wiring work must be done by a
qualified electrician, and the metal part of the unit must be well grounded. The ground wire of the
power supply connected must be reliable and effective, otherwise the risk of electric shock will
occur.

7
When the power supply is connected, it must be equipped with a full-pole disconnection device
matching with the unit and at least 3mm² contact distance from the power supply and a
leakage protection device. If the supply cord is damaged, it must be replaced by the manufacturer,
its maintenance department or a similar professional in order to avoid danger.
In distribution box shall be ground protection, air source heat pump units must add grounding
(grounding), grounding is no less than Φ10 galvanized round steel,embedded depth of not less than
0.6 meters. The ground protection line (PE) shall be no less than 50% of the main line, that is, 1mm²
After the completion of all the wiring work, the power can be connected after careful inspection；
Do not install in the bathroom and other high temperature wet water occasions.
Do not use in places with lampblack (e.g. kitchen).
Please take a breath when using the appliance at the same time.
Do not use the insecticide sprays while units are running; (after the use of pesticides, the indoor air
should be fully circulated, otherwise the unit will accumulate chemical ingredients, which is harmful
to human health).
Do not insert hand or foreign matter into the outlet of the main engine of the hot water unit, which
will cause danger to personnel and equipment.
The water quality used by the unit must meet the national standard of domestic water for residents.
Otherwise, the company will not be responsible for any damage to the unit.
2.3.Special attention for the connection of drainage pipe and water pan in the attachment:
Secure the joint with a sleeve.
The whole section of the drainage pipe is wrapped with insulation pipe, and the pipe should be
made into a sloping shape (tilted outward from the interface of the water plate), and the middle
should not be twisted, raised, undulating and so on.
The outlet should be kept clear of water and not immersed in water.
3. Unit wiring diagram and wireless water pump connection instructions
3.1.Unit wiring diagram (the connection method between the unit and the power supply
and the interconnection method of each independent component shall be subject to
the circuit diagram posted on the unit)
Wiring diagram

8
Waterway system diagram
3.2.Wireless water pump connection instructions
Wireless communication pairing (a pair of water pump plates should be matched with an inner
plate)
When the power is on, the LED3 of the power supply lamp is lit, and the pairing button (SW1) is

9
pressed continuously for 6 times within 10 seconds. The wireless status LED1 flashes at a frequency of
0.5hz to enter the wireless pairing state.
100ms cycle sends the automatically generated synchronization code and address code of the
internal unit (the configured number of internal units plus 1 is the sending address), no reply is received
within 30 seconds, the wireless status light is off, and the pairing fails.
After receiving the reply, the wireless module synchronization code is configured according to the
automatically generated value. After 100MS, the query instruction is sent to the internal unit of the
matching address in a loop. No reply is received within 30 seconds, and the wireless status light is off
and the pairing fails.
After receiving the reply, the pairing is successful, the number of the configured internal unit is
increased by 1, and the negative code is saved, and the wireless status light is lit up.
This cycle pairs multiple internal units, up to 32 internal units.
Reset pairing method：
When the power is on, the LED3 of the power supply lamp is lit up. Press the pairing button (SW1)
for 10 times continuously within 10 seconds to cancel the pairing；
Wireless communication query：
After power on, a pair is detected and the wireless status light is always on. Otherwise, the light
will go out and the module will be in the waiting state
；
When the internal unit requires the pump to be turned on, the pump shall be powered on and the
corresponding indicator LED2 shall be on, otherwise off
；
Internal unit wireless matching (one water pump plate should be matched with one internal unit
plate)
Power on, press the remote control switch button continuously for 6 times within 10 seconds, the
buzzer will sound, and wait for receiving the pairing information. If the pairing fails within 30 seconds,
the pairing failure will be reported, and the digital tube will display "09".
IV. Daily maintenance
1. Cleaning
External cleaning：Cleaning machine must be cut off the power, with a wet cloth dipped in a small
amount of neutral detergent gently wipe. Do not use gasoline or acid solution, alcohol, and dry with
a dry cloth.
Fin heat exchanger cleaning：The evaporator fins can be cleaned with a hard nylon brush. Vacuum
cleaners must be used before scrubbing. If there is compressed air, the fin heat exchanger can be
cleaned with high-pressure air tube.