Entel HT649 Series User manual

PREPARING YOUR RADIO FOR USE
Attaching / removing the antenna
Attaching / removing the battery pack
1. To attach, carefully align the antenna with the
socket. Screw in the antenna and clockwise
(taking care not to cross the thread) until it
is seated rmly with the accessory cover’s
rubber ring between the antenna and the top
of the radio. (A)
2.To remove, unscrew the antenna
anti-clockwise. (B)
1. To attach, locate the pegs on the bottom of the
battery into the slots on the radio and press
the top of the battery against the radio. Secure
battery by tightening the screw clockwise
by hand. (Do not use any implement or
overtighten). (C)
2.To remove, unscrew the locking screw anti-
clockwise and pull the battery away from the
top of the radio. (D)
A
B
C
D
SWITCHING ON, RECEPTION
AND SWITCHING OFF
1. To switch on, press and hold the on/off control
(1) on the front of the radio.
2.When the radio has passed its diagnostic tests,
it will emit a fanfare tone.
3.The radio will enter standby mode. This is
indicated by the LED Amber ashing once
every 5 seconds, signalling that the radio is
ready for use.
4.Adjust the volume control to select the desired
volume level.
5. Using the channel buttons, ensure you have
the correct channel selected.
6.When receiving a valid signal, the LED will
illuminate steady green and audio will be
emitted from the radio’s speaker or audio
accessory (if attached)
7. When nished using the radio, switch off
by pressing and holding the on/off button
(1) until the radio beeps and the LED/LCD is
extinguished.
TRANSMITTING
1. Perform steps 1 through to 5 of Switching On,
Reception and Switching Off.
2.Before transmitting, monitor the channel and
make sure it is clear.
3.When receiving a signal, wait until the signal
stops before transmitting. The radio cannot
transmit and receive simultaneously.
4.Press the PTT (Push To Talk) button (4) to begin
your transmission. To conrm transmission the
LED illuminates red.
5. For best transmitted speech quality you must
talk directly into the radio’s microphone (10) at
ar ound 4cm be t ween yo ur mout h and the rad io.
6.Please note: if you talk into the top of the
radio or with your mouth fur ther away, you will
transmit poor quality speech
7. When the transmission is nished release the
PTT button.
www.entel.co.uk
EU DECLARATION OF CONFORMITY
We Entel UK Limited of:
320 Centennial Ave, Centennial Park,
Elstree. WD6 3TJ United Kingdom
Tel [phone]
[e-mail]
Declare under our sole responsibility that the
product ranges specied below conform to
the following standards or other nominative
documents.
HT649
EN 300 225: December, 2015 v1.5.1
EN 301 843 -2: June, 2004 v1.2.1
EN 60945: October, 2002, Edition 4
IEC 60945/Corrigendum 1: April, 2008, Edition 4
IMO Resolution A.694 (17): 1991
IMO Resolution A.809 (19): 1995
ITU-R M.489-2: October, 1995
MSC Resolution 147 (77): June, 2003
For Assessment see:
EC Type-examination (Module B) certication
No. 13212002/AA /06 of 21 March 2017
Product quality assessment system (Module D)
Certicate No. P133(issue 7) of 06 June 2017
Product Category: A.1/5.17
Issued by Telecations B.V
Edisonstraat 12A, 6902 PK Zevenaar, The
Netherlands.
This declaration is issued according to the
provisions of European Council Directive 96/98/
EC on marine equipment amended by the
Commission Directive 2010/68/EU
Name: Mike Jamieson
Position: Quality Manager
Date: 8th June 2017
Signed:
HT649
Quick Start User Guide
Designed in the United Kingdom
All Rights Reserved. Copyright Entel UK Ltd.

Quick Start User Guide V2.4
INTRODUCTION
The Entel HT649 is a GMDSS IP68 submersible marine handheld radio that
operates on the VHF marine band and has 19 channels.
To meet your exact requirements the radio may have been customised by
your Entel dealer. These features will be explained in a separate guide
issued by the dealer.
PACKI NG LI ST
PACKAGE 1
HT649 Marine VHF radio
CLB750G Primary battery
CAT40 High efciency antenna
LY600 Lanyard
PACKAGE 2 AS PACKAGE 1 PLUS
CNB750E Rechargeable Li-Ion battery (secondary)
CCAHT Trickle charger pod
CWCHT Mains adaptor
CWCHT12 12v charger lead
ASPACKCAHV3 Bulkhead screw and spacer kit
OPTIONAL ACCESSORIES
Attaching and removing accessories
1.To attach an accessory, remove the accessory
cover by unscrewing the locking screw anti-
clockwise (leave the cover attached or store in
a safe place).
2.Plug the accessory into the socket, then
carefully tighten the locking screw clockwise
until nger tight (do not overtighten or use any
implement)
3. To remove an accessory, unscrew the
locking screw of the accessory by hand in
an anti-clockwise direction. Ensure you re-t
the accessor y socket cover (the radio is not
submersible without the socket covered).
BATTERY I N FORMATI O N
Primary (CLB750G - Yellow) battery use
1. This is a non-rechargeable, single use Lithium battery
2.The battery is supplied with a security seal that must only be removed
immediately before use
3.An expiry date is printed on the batter y. Regularly check the date of your
batteries and replace as required. Immediately, and safely, dispose of any
out-of-date batteries.
Secondary (CNB750E - Black) batter y charging
1. Connect the AC adaptor or 12V charging lead to the charger pod
and plug in
2.Turn the radio of f and insert the battery pack into the charger pod, either
with or without the radio attached. The charger LED status light changes
to red and charging begins
3.When charging is complete, the charger status LED changes from red to
green (a fully discharged battery pack will take approximately 6 hours to
recharge)
CAUTION
BATTERY PACK PRECAUTIONS
• Do not recharge the battery pack if it is already fully charged. Doing so
may reduce the life of the battery pack
• After charging is complete, remove the battery from the charger
• Please ensure that the radio is turned off before placing it in the charger
and never switch a radio on whilst in the charger
• Only use Entel branded battery packs and chargers
• Do not shor t the battery terminals or dispose of the battery in a re
• Do not charge the radio and/or battery pack if they are wet
DANGER
DO NOT DISASSEMBLE OR MODIFY THE BATTERY IN ANY WAY!
Your Entel battery pack incorporates a safety circuit to avoid danger, if the
safety circuit is damaged or bypassed, or the battery cells are damaged
directly, they may generate extreme heat, smoke, rupture and emit ames.
CONTROLS & INDICATORS
7 KEY LCD
1. On/Off button. Press and hold to turn the radio on or off
2.MEM Button: Adds / removes the currently selected channel to / from
the scan list.
SCAN Button: Starts/Stops scanning the channels added to the scan
list.
16 Button: Toggles between the currently selected channel and
channel 16.
MON Button: Latches squelch open
3.Channel up / down buttons
4.Push To Talk (PTT) button. Press to speak and release to listen.
5. Non-programmable button
6.Short press toggles LCD and keypad backlight on/off. Long press
toggles keypad lock on/off
7. Non-programmable button
8. LED Indicator
Red steady - Transmitting
Red ashing slowly - Battery needs recharging
Green steady - Receiving
Amber pulsing – In standby mode
9. Volume Control
10. Microphone
1
2
8
9
5
4
6
10
T
a
l
k
H
e
r
e
3
7