EOB WS360 User manual
433.92 MHZ
CR2032
IP20
UNIVERSAL TRANSMITTER UNDER THE
SWITCH
WS360
WS360
WIRELESS
TRANSMITTER
Designed and manufactured in CZ.
EU DECLARATION OF CONFORMITY
Here is ELEKTROBOCK CZ s.r.o. declares that the WS360
radio equipment complies with Directive 2014/53 / EU. The
full text of the EU Declaration of Conformity is available at
the following Internet address: www.elbock.cz
150m
Description
WS360 serves as a transmitter for wireless bells of the BZ90x
series as well as for remote control of WS3xx receivers, which
can switch various el. appliances (lighting, blinds, electric
locks, direct heaters, etc.).
The transmitter contains 4 inputs (K1 to K4). When any
channel is pressed, a coded signal is sent to the learned
receiver that performs the function.
Each channel can have a dierent function and control several
receivers at once.
Signal transmission is indicated by a red indicator diode.
Notice
Do not place the transmitter near power cables and large
metal objects! It must not be mounted on metal substrates!
Designed for indoor use! In case of improper placement, the
reach of the whole set will be signicantly reduced!
Construction
The transmitter is designed for installation in the KU / KP68
installation box.
a) Remove the rear cover of the transmitter,
b) remove the battery cover paper,
c) reinstall the back cover,
d) connect the transmitter according to the wiring diagram,
e) pair with the receiver.
K1
K2
K3
K4
COM
WS360
TL
Diagram of connection:
Wood / plasterboard Glass
Wall
Reinforced concrete
Metal
The transmitter must not be mounted on or in close proximity
to metal substrates, eg metal door frames. Improper installation
will signicantly reduce the range of the kit or even cause it to
malfunction.
The range between wireless devices is greatly aected by the
distance between the transmitter, receiver, and obstacles on
a straight line between them. The material from which the
walls are made also decides. The reach is least aected by the
weak wall of plasterboard or brick. On the contrary, reinforced
concrete ceilings tend to be the worst. In practice, the range
can be signicantly smaller (up to one-fth) than in the open.
RF signal throughput
Pairing with receivers
1) Put the receiver in learning mode according to the instructions
of the respective receiver.
2) Press the button on the transmitter (WS360) with which you
want to control the receiver.
3) In case of successful pairing, the indicator LED on the receiver
ashes.
Battery replacement
The need to replace the battery is indicated on the receiver (see
WS3xx manual). Always use a 1x 3V CR2032 battery. Dispose
of the used battery in accordance with the regulations for
hazardous waste!
a) Remove the rear cover of the transmitter,
b) Remove the battery from the holder,
c) Insert a new battery and reinstall the back cover.
When inserting the battery, pay special attention to its
polarity.
RF
WS301 Receiver under the switch
Order No.: 3301
WS302 Wall receiver
Order No.: 3302
WS303 Receiver into the socket
Order No.: 3303
The following elements can be controlled using the WS360
transmitter:
Controlled elements
WS305 Receiver for blinds
Order No.: 3305
WS306 Receiver bell-GONG
Order No.: 3306
WS307 Bell-SIREN receiver
Order No.: 3307
WS304-4-5VDC DIN rail receiver
Order No.: 3404
WS304-10 DIN rail receiver
Order No.: 3304
Further details can be found at www.elbock.cz
Wireless transmitter
WS360
WS360
The universal transmitter under the WS360 switch can
be used as a spare button for BZ9xx wireless doorbells,
but also for controlling other wireless products with self-
learning code (WS3xx series) from ELEKTROBOCK CZ.
Advantages:
- installation under the switch
- maintaining the design line of switches in the house
Technical parameters
Power supply battery, CR2032
Transmitting power <10 mW
Frequency 433,92 MHz
Battery life up to 5 years
Degree of protection IP20
Operating temperature 0 up to +40 °C
Operating humidity <95 % RH, non-condensing
Mounting type under the switch, to KU / KP68
Dimensions (HxWxD) 36x49x13 mm
The product is covered by a 2-year
warranty from the date of purchase.
In the case of warranty and post-
warranty service, send the product to
the manufacturer‘s address together
with a copy of the proof of purchase.
ELEKTROBOCK CZ s.r.o.
Blanenská 1763
Kuřim 664 34
Tel.: +420 541 230 216
Technical support (up to 2 pm)
Mobile: +420 724 001 633
+420 725 027 685
www.elbock.cz
Pb
LEAD FREE
RoHS compliant
8 595689 100261
Table of contents
