Epcom EYH003FAP User manual

Hidden CCD Camera
Instruction Manual
R040525A/4-SYS

Thank you very much for purchasing our product. Before operating this
product, please readthis instruction manual carefullyto ensure proper use.
1. Safety Precautious
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN!
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NOUSER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Disposal of Old Electrical & Electronic Equipment (Applicable in
the European Union and other European countries with separate
collectionsystems).
Please do not directly touch the sensor element. If necessary, use
a soft cloth moistened with alcohol to wipe off any dust.
Please be extra careful not to shake the camera.
Please avoid places where there is direct sunlight or reflected sun
light as PIR alarm features are affected by environmental changes.
2. Description
The camera employs digital signal processor (DSP) chip-set for image
control, and all integrated state circuitry which provide extremely long
life and high reliability. This camera offers excellent image quality with
low lag and high burn resistance, and is not subject to distortions from
magnetic fields.
Highly resistance to shock and vibration, easy to install, this
camera is a very good choice for your color CCTV system.

2
3. Feature
Employs Digital Signal Processor (DSP) chip-set for image control.
Pixel number: NTSC=480K/ PAL=570K for ultra high resolution and
NTSC=380K/ PAL=440Kforhigh resolution.
High sensitivity, low smear, high anti-blooming and high S/N ratio.
Powerful functions: Auto Electronic Shutter (AES), Auto Iris (AI),
Auto Gain Control (AGC), Auto White Balance (AWB), Back Light
Compensation (BLC), and Noise Reduction (NR function depends
on model type).
4. Contents
Item
Name of Part
Quantity
1
Camera
1
2
Instruction Manual
1
3
Mounting Bracket Bag
1
A
Base plate (optional)
1
B
Supporting Arm
1
C
Mounting Bracket
1
4
Appurtenance Bag
1
A
Screws
3
B
Anchor
3
C
4Pin or 6Pin Cable (optional)
1

3
5. Installation
(1) Use the 3 screws provided to attach the mounting bracket to the
surface or wall, assemble all spare parts to the base plate and
tighten the camera wingnut .
(2) Screw the mounting bracket into the camera mounting post; then
adjust the camera to approximate location and tighten the
camera wingnut.
C A
D
C A
D
B
Figure 1
E
E

4
6. WIRING
1. Connect the video input connector on the video monitor to the
video output connector of the camera with 75-ohm coaxial cable.
2. Insert the AC plug into the AC power socket and the DC plug to the
DC Jack.
Note: AC adapter is sold separately.
7. DETECTOR BOARD (NOT AVALIABLE FOR EYH003FAP)

5
Options
Description
1.LED Selector:
(3PINS: Top, Center, Bottom)
A. Top + Center w/black cap: Upon Walk-testing: Light
blinking (Disadvantages: Easy to identify as a security
system.)
B. Center + Low w/black cap: No light blinking while
detecting. (Advantages: less obvious)
2.Sensitivity Adjustment:
A. To raise sensitivity: Turn clockwise to detect longer distance
and wider pattern.
B. To lower sensitivity: Turn counter clockwise for detection in
narrow areas.
3.Dwell Time Adjustment:
Adjustable from 2 to 40 sec.
For closure period of N.C/N.O relay connected to an alarm
panel, light control or recording control of time lapse VCR, etc.
A. Max. time: Turn counter clockwise.
B. Min. time: Turn clockwise.
Top + Center pins of “J4” must be selected to adjust the time
setting.
4.Alarm control, Light
control or Recording
control
(N.O or N.C)
(3PINS: Top, Center, Bottom)
A. Top + Center w/black cap: Operate with “VR2” to adjust
time. (To set the relay output of the Light control or
Recording control, the time is selected by individual
preference or application.
B. Center + Bottom w/black jumper: Relay output can be set for
Security control panel for only 2 seconds.
Note: N.C./N.O. relay output current: 1A125 VAC, 2A30 VDC.
5.Pulse Control:
Once or twice
4PINS:2PAIRS w/jumperconnector
Position 1: Set to “ONCE” for instant reaction when PIR
detects someone: and either the “alarm or Security
control panel” or “Recording control” will be
triggered immediately.
Position 2: Set to “Twice” when PIR detects someone 2 times
within 15 seconds.
6.Output Terminals:
24 Hour/Anti-Tamper
N.C.: Normally Closed
A. For connection to: Security panel or Light control CCTV
…etc.
B. With anti-tamper function for 24 hours.
N.O.: Normally Open Contacts
※P.S.: Relay output current: 1A 125VAC, 2A 24VDC
0.5A 230VAC, 2A 24VDC
7.Power: 12V DC
Standby Current: 3mA,
Working Current: 28mA
Caution:
The PIR is triggered by body movement, excluding fixed
objects, however, do not place in direct sunlight or reflected
sunlight.
J1
“VR1”
High
Low
“VR2”
Min.
Max.
J2
1
2
JP2
N.C.
N.O.
+
-
J4

6
Wide angle lens up to 100°, coverage areas to 30x30 feet.
Provide 64 beans in 3 layers.
10 20 30
100¢X TOP VIEW
302010
SIDE VIEW
feet
feet

7
8. Specification
According to the camera purchased, select and refer to the appropriate specification below:
Model no.
EYH003FAP
Image Device
1/3” Color CCD Super HAD II (Sony Chipset)
Picture
Elements
NTSC: 976 x 494
PAL: 976 x 582
Resolution
650TVL
Min Illumination
0.02Lux/ F1.2
S/N Ratio
More than 48dB
Electronic
Shutter
NTSC: 1/60S~1/100,000S; PAL: 1/50S~1/100,000S
Gamma
0.45
Lens Furnished
Cone Lens 3.7mm
White Balance
Auto
Gain Control
Auto
Sync. System
Internal
Video Output
1Vp-p/ 75 Ohms
Power Supply
DC 12V±10％
Power
Consumption
90mAmax
Note: Design and specifications are subject to change without prior notice.